Ciclo HAC 5 Manual

Ciclo Pulsmåler HAC 5

Læs gratis den danske manual til Ciclo HAC 5 (4 sider) i kategorien Pulsmåler. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Ciclo HAC 5, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

ATTENTION! To save energy, the 5 turns off automatically at night, meaning the dis-HAC

play turns off at 12 p.m. and only lights up again after pressing any button.

All functions active at the time of shut-off keep going internally despite the display tur-

ned down.

Operational Setup

2.1 Attaching the HAC5 to the wrist band and the handlebar bracket

To take the HAC5 out of the wrist band or the handlebar holder, turn it 90° to the left, then re-

move.

To insert into the wrist band or handlebar bracket, insert at a 90° angle to the left, then turn to

right until it engages.

Inserting the batteries

• Inserting the battery into the HAC5:

Open the battery cap on the back of the HAC5with the aid of a coin

(turn counter clockwise). Insert battery type CR2032 with plus pole fa-

cing up, please make sure that the battery is inserted at a angle from

the side (from right to left), so that the contacts lie on the battery. Then

close the battery cap. The display of the shortly shows all seg-HAC5

ments, then returns to the normal display.

• Inserting the battery into transmitter belt, speed- and cadence transmitter:

Open the battery cap with the aid of a coin (turn to left). Insert battery type CR2032 with the

plus pole facing up and close the cap again.

Setup / Initialization

Because of the new digital transmission technique, all transmitters have to be initialized prior to

first use. We therefore recommend that you first conduct all necessary initializations (and, if re-

quired, enter all required data) before attaching the parts to the bike. On page 3 (examples)

you will find a step-by-step setup as well for the initializations as for setup of time and date.

Installing

• Installing the handlebar bracket:

The handlebar mounting can also be installed on a stem. To do this the

top section of the handlebar mounting must be removed from the bot-

tom section. To make it easier to remove the top section carefully push

the sides of the bottom section upwards slightly.

Then turn both parts through 90° and assemble them

again until the snap-on mounting engages.

Remove the backing foil from the underside of the

handlebar mounting, place the handlebar mounting in

the required position on the handlebar (or on the stem)

and press it down slightly. Secure it with the O ring or

with the cable ties

“First steps” with the

handlebar

bracket

HAC5 Anl. 125x250 engl 25.07.2006 15:41 Uhr Seite 1

• Installing the speed transmitter:

Attach the speed transmitter at the fork or the rear construction

with the aid of the cable ties (the printed side of the transmitter

with the marking must point to the spokes).

Mount the magnet to a spoke directly opposite the marking on

the transmitter.

Do not over tighten the fixing screw on the magnet. Adjust transmitter in such a way that the

distance between transmitter and magnet does not exceed 3 millimetres.

• Installing the cadence transmitter:

Attach the cadence transmitter to a strut opposite the pedal crank with

the aid of the cable ties (the printed side of the transmitter with the mar-

king must point to the crank).

Mount the magnet on the pedal crank directly opposite the transmitter

with the help of the cable tie, so that the magnet points exactly to the

marking on the transmitter. Adjust transmitter in such a way that the

distance between transmitter and magnet does not exceed 3 millimetres.

Putting on the breast belt

Hang the transmitter belt in the elastic breast belt and then put the breast belt

around your (naked) upper torso. The transmitter (plastic part with inscription)

should be placed above the middle of your upper stomach region, slightly be-

low the breast and the inscription on the transmitter (when seen from the front)

must be legible (pictured).

Pacemaker wearers should consult their doctor before using any heart rate measuring

device!

If your skin is too cold or too dry, the electrical contact between the skin and the electrodes can

be so minimal that an accurate measurement is not possible. It often helps to wet the electrodes

and the skin where they are to be attached with your finger (do not wet the transmitter but only

the rubber parts on the left and on the right). If this doesn’t help, one should train until they start

sweating. You will get the best contact by means of a special electrode-gel (available at your lo-

cal pharmacy).

Using the buttons

The display of the HAC5is separated into 3 areas: an upper, a and a middle lower. Each

area displays one function, so that there are three functions displayed simultaneously at all

times. This means that the possible functions can be combined to personal taste.

The buttons are termed as follows in the manual:

U Lpper eft button: UL-button

U M UMpper iddle button: -button

U Rpper ight button: -buttonUR

M Riddle ight button: -buttonMR

L Lower eft button: LL-button

L Rower ight button: LR-button

The following applies:

The buttons on the right side main functionsaccess the

(UR-, MR- and LR-buttons).

The sub-functions of the functions in the upper and lower display are accessed through the

depending button on the left side (UL- and LL-buttons).

The stopwatch and the countdown are started, stopped and paused by shortly pressing the

UM-button and reset by pressing the -button for three seconds (this also deletes all split-UM

and lap times).

Every press of the button makes a short sound, this sound can be turned off in the advanced

settings.

Transmitter search – digital system

In order for the HAC5to display speed or heart rate or similar, the according transmitter has to

be found first.

The search begins automatically when a recording is started ( - and UL LL-buttons pressed si-

multaneously for three seconds), and manually by pressing the LL-button for three seconds (in

both cases, the active profile is shown for 10 seconds).

During this display all transmitters are searched for which are active in this profile. Should no or

not all transmitters be found during this time, then this is displayed when selected, for example:

➔

Mark

Electrodes

Transmitter

HAC5 Anl. 125x250 engl 25.07.2006 15:41 Uhr Seite 2

Produkt Specifikationer

Mærke:	Ciclo
Kategori:	Pulsmåler
Model:	HAC 5

Har du brug for hjælp?

Hvis du har brug for hjælp til Ciclo HAC 5 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Pulsmåler Ciclo Manualer

Ciclo HAC 5 Manual

27 August 2024

Ciclo HAC 4000 Manual

27 August 2024

Pulsmåler Manualer

Nyeste Pulsmåler Manualer

Wahoo Tickr Fit Manual

1 August 2025

Dexford HR 400BT Manual

22 Juli 2025

Teesa TSA8071 Manual

6 Juni 2025

Crane AF5-CDBT-5 Manual

4 Marts 2025

Ranex F18 Manual

11 Januar 2025

Garmin HRM-DUAL Manual

6 Oktober 2024

Medel Clip & Go Manual

27 September 2024

Bowflex Heart Rate Armband Manual

23 September 2024

Polar A1 Manual

16 September 2024

Polar H6 Manual

3 September 2024