Cisco SPA 500S Manual

Cisco Ikke kategoriseret SPA 500S

Læs gratis den danske manual til Cisco SPA 500S (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 59 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 30 anmeldelser. Har du et spørgsmål om Cisco SPA 500S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick Start Guide

Cisco Small Business

SPA 500S 32-Button Attendant Console for Cisco

Small Business SPA 500 Series IP Phones

Package Contents

• SPA 500S 32-Button Attendant Console for Cisco Small Business SPA

500 Series IP Phones

• Quick Start Guide

• Attachment Arm

• Attachment Arm Screws (2)

• Auxiliary Interconnect Cable

• Stand

Connecting the Equipment

The following procedure describes how to attach the Cisco SPA 500S to a

Cisco SPA 500 Series IP Phone.

S 1TEP Turn both the Cisco SPA 500 Series IP Phone and the Cisco SPA 500S

face down.

S 2TEP Align the screw hole in the Cisco SPA 500 Series IP Phone with one of

the holes on the attachment arm.

S 3TEP Insert the pegs on the attachment arm into the peg holes as shown

below on the Cisco SPA 500 Series IP Phone.

S 4TEP Using an attachment arm screw, secure the attachment arm to the

Cisco SPA 500 Series IP Phone.

S 5TEP Align the right screw hole in the Cisco SPA 500S with the unused hole

on the attachment arm.

S 6TEP Insert the pegs on the attachment arm into the peg holes on the Cisco

SPA 500S.

S 7TEP Using an attachment arm screw, secure the attachment arm to the

Cisco SPA 500S.

CAUTION Do not plug a telephone line cord into the AUX port. Use only the

auxiliary cable provided with the Cisco SPA 500S.

S 8TEP Locate the AUX IN port on the back of the Cisco SPA 500S. Connect

one end of the auxiliary cable to this port.

S 9TEP Locate the AUX port on the back of the Cisco SPA 500 Series IP Phone.

Connect the other end of the auxiliary cable to this port. The Cisco SPA

500S is powered by the auxiliary cable with the Cisco SPA 500 Series

IP Phone; no additional power source is required.

STEP10 Route the auxiliary cable inside the cable slot of the Cisco SPA 500S.

STEP11 Attach the appropriate desktop stand to each unit.

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

www.cisco.com

Small Business Support US: 1-866-606-1866 (Toll Free, 24/7)

Small Business Support, Global: www.cisco.com/go/sbsc

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and

other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks.

Third party trademarks mentioned are the property of their respective owners. The use of the word

partner does not imply a partnership relationship between Cisco and any other company. (1005R)

78-19057-01B0

Connecting a Second Cisco SPA 500S

A maximum of two Cisco SPA 500S attendant consoles can be connected to a

Cisco SPA 500 Series IP Phone. The instructions in this section are for

connecting a second SPA500S. If you are not attaching a second Cisco SPA

500S, skip to the Configuring the Cisco SPA 500S section.

S 1TEP Attach the first Cisco SPA 500S to the IP phone and connect the

auxiliary cable as described in Section 1, Connecting the Equipment.

S 2TEP Align the left screw hole in the first Cisco SPA 500S with one of the

holes on the attachment arm.

S 3TEP Insert the pegs on the attachment arm into the peg holes on the Cisco

SPA 500S.

S 4TEP Using the attachment arm screw, secure the attachment arm to the first

Cisco SPA 500S.

S 5TEP Align the right screw hole in the second Cisco SPA 500S with the

unused hole on the attachment arm.

S 6TEP Insert the pegs on the attachment arm into the peg holes on the Cisco

SPA 500S.

S 7TEP Using the attachment arm screw, secure the attachment arm to the

second Cisco SPA 500S.

CAUTION Do not plug a telephone line cord into the AUX port. Use only the

auxiliary cable provided with the Cisco SPA 500S.

S 8TEP Locate the AUX OUT port on the back of the first Cisco SPA 500S.

Connect one end of the auxiliary cable to this port.

S 9TEP Locate the AUX IN port on the back of the second Cisco SPA 500S.

Connect the other end of the auxiliary cable to this port.

STEP10 Route the auxiliary cable inside the cable slot. The Cisco SPA 500S is

no additional power source is required.

STEP11 Attach the appropriate desktop stands to each unit.

Configuring the Cisco SPA 500S

You can configure the Cisco SPA 500S buttons for speed dials, line monitoring,

one-touch transfer, and other features (if supported by your phone system). To

configure the Cisco SPA 500S:

• If the Cisco SPA 500S and attached Cisco SPA 500 Series IP Phone are part

of a Cisco SPA9000 Voice System, we recommend that you use the Cisco

SPA9000 Setup Wizard. See the

System Configuration Using the SPA9000

Setup Wizard Installation and Configuration Guide

on Cisco.com.

• If you want to manually configure the Cisco SPA 500S using the web-based

configuration utility for the Cisco SPA 500 Series IP Phone to which the

Cisco SPA 500S is attached, see the

Cisco SPA 300 Series, SPA 500

Series, and WIP310 IP Phone Administration Guide

on Cisco.com. This

guide also contains instructions for using the Cisco SPA 500S and attached

Cisco SPA 500 Series IP Phone with a SIP call server, such as BroadSoft or

Asterisk.

NOTE If you are using the Cisco SPA 500S and Cisco SPA 500 Series IP

Phones with the Cisco Unified Communications Series for Small Business,

use Cisco Unified Communications Manager Express or Cisco Configuration

Assistant for phone and attendant console configuration and administration.

Using the Cisco SPA 500S

You can press a button on the Cisco SPA 500S to dial an associated line, pick

up a call ringing at a line, or transfer a call to the line.

The options available on the Cisco SPA 500S depend on the phone system

configuration. Your phone system might not provide all of the features

mentioned in this document.

Monitoring Lines

The color of a line button gives you information about the line being monitored.

SIP System:

• Green (steady): The line is idle.

• Green (blinking): The phone is in call-back mode.

• Red (steady): The line is in use.

• Red (slow blinking): The line is on hold.

• Red (fast blinking): The line is ringing.

• Orange (blinking): Phone registration has failed.

• Off: The line is not configured.

SPCP System:

• Green (steady): The line is in use.

• Green (blinking): The phone is on hold.

• Orange (blinking): The line is ringing.

• Off: The line is not configured.

Where to Go From Here

Support

Cisco Small Business

Support Community

www.cisco.com/go/smallbizsupport

Cisco Small Business

Support and Resources

www.cisco.com/go/smallbizhelp

Phone Support Contacts www.cisco.com/en/US/support/

tsd_cisco_small_business

_support_center_contacts.html

Cisco Small Business

Firmware Downloads

www.cisco.com/cisco/web/download/

index.html

Select a link to download firmware for Cisco

Small Business Products. No login is

required.

Downloads for all other Cisco Small Business

products, including Network Storage

Systems, are available in the Download area

on Cisco.com at www.cisco.com/go/

software.

Product Documentation

Cisco Small Business

SPA 500 Series IP

Phones

www.cisco.com/go/spa500phones

Cisco Small Business

Cisco Partner Central

for Small Business

(Partner Login Required)

www.cisco.com/web/partners/sell/smb

Cisco Small Business

Home

www.cisco.com/smb

Produkt Specifikationer

Mærke:	Cisco
Kategori:	Ikke kategoriseret
Model:	SPA 500S
Bredde:	101 mm
Dybde:	39 mm
Højde:	201 mm
Vægt:	900 g
Produktfarve:	Sort
Kapacitet for telefonbog:	32 entries