Clever Family Homes CFHSO0200 Manual

Clever Family Homes Ikke kategoriseret CFHSO0200

Læs gratis den danske manual til Clever Family Homes CFHSO0200 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Clever Family Homes CFHSO0200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CFHSO0200- Installation Guide

1.1

support@cleverfamilyhomes.com

cleverfamilyhomes.com/power-protection

⚡

⚡⚡ Heavy Duty -Amp 2400-Watt Appliance Surge Protector 20

Smart Plug Kit with outlet saver power cord.

Contents:

• One protector in a plastic blister pack.

• 1- foot power extension cord (optional).

Preparation:

• If required, pull the appliance away from the wall, or enclosure,

to access its power outlet. Leave out for at least 1 hour to test.

• If there is another device plugged into the same outlet, use the

extension cord to plug it in after the protector install.

• It is a good idea to test the wall outlet is grounded and is wired

correctly using a “outlet tester”.

Configuration:

• Using a flat screwdriver, set the lower voltage threshold level on

the back of the plug. We recommend setting it to 95V.

Install:

• Make sure the black power switch is in the off position (0) on the

front of the protector .

• Plug your appliance into the protector socket and then insert the

protector into the wall outlet.

• Turn on the protector switch (1).

LED status check:

• The waiting light may display for 3 minutes before yellow a

stable voltage is detected and the normal green light comes on.

• If the waiting light, or the over/under lights, or no yellow red

lights are displayed for over 10 minutes, then read the

troubleshooting guide over the page.

• Run the appliance for 1-2 hours and check the LED status is ok.

Post Install:

• If required, use the 1-foot power cord to plug in any secondary

device into a double or triple outlet. It is preferable that only the

protector is plugged into the wall outlet and nothing else.

CFHSO0200- Installation Guide

1.1

support@cleverfamilyhomes.com

cleverfamilyhomes.com/power-protection

Troubleshooting

A - No power and

no lights after

install.

• Make sure the protector is turned on (1) in the front.

• Test the wall socket is live and the breaker switch has not tripped.

• Test the protector on another wall socket e.g. lamp.

• If the lights still don’t come on, order a replacement.

B - No power and

yellow waiting

light stays on

after install.

• This usually means that there is an unstable voltage, or the wall

outlet is not grounded/wired correctly. Test the wall socket ground

and wiring using an outlet tester.

• Try switching the plug off and then on again. If that does not work,

leaving the switch on (1), pull the whole protector out and plug in

again directly into the wall socket.

• The equipment power draw may be too high and exceed the max

voltage/amps/watts. Set the low voltage setting to 90V, unplug any

other equipment, any extension cord and try again.

• If you have a watt tester, use it to check the max power draw.

C - Trips after

short time of use

after install.

• The green normal light comes on, the equipment runs and then the

plug trips after a short time and goes into yellow waiting, or red.

• The equipment power draw may be too high and exceed the max

voltage/amps/watts. Set the low voltage setting to 90V, remove the

extension cord, unplug any other equipment, and try again.

• Test the wall socket ground and wiring using an outlet tester.

• If you have a watt tester, use it to check the max power draw.

• If the red low voltage light is displayed, reduce the low voltage

threshold on the back of the plug to 90v.

D - No power, no

lights, stays in

yellow waiting or

red for a long

period after a

power surge.

• Sometimes power surges can be excessive, and the protector can get

damaged in the line of duty. Sometimes you don’t even know.

• Usually the protector auto-resets itself after a power surge, but

sometimes may need to be manually reset using the A or B

troubleshooting sections above.

• If the protector continues to fail it has done its job and , it’s time to

order another one. It’s also useful to keep replacements handy.

Warranty and

Replacement.

• All parts and workmanship are under warranty for 12 months from

time of purchase. If within this time, the protector is not operating as

expected then it may be replaced or refunded at no cost. Go through

your store or contact Clever Family Homes Support with the order id,

name/address, and date (attach the packing slip if possible).

Please help us improve. Leave us some feedback or post a review.

Produkt Specifikationer

Mærke:	Clever Family Homes
Kategori:	Ikke kategoriseret
Model:	CFHSO0200

Har du brug for hjælp?

Hvis du har brug for hjælp til Clever Family Homes CFHSO0200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Clever Family Homes Manualer

Clever Family Homes CFHSO0500 Manual

23 Juni 2025

Clever Family Homes CFHSO0200 Manual

23 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Anker SOLIX RS40P Manual

16 August 2025

Middle Atlantic C3-FANKIT Manual

16 August 2025

Yamaha KX61 Manual

16 August 2025

Anker SOLIX RS40 Manual

16 August 2025

Biltema 82-3824 Manual

16 August 2025

VAIS Technology Soundlinq 3 Manual

16 August 2025

PreSonus UC Surface Manual

16 August 2025

ART X-11 Manual

16 August 2025

Biltema 18-597 Manual

16 August 2025

Evenflo Aero² Manual

16 August 2025