Code CRD900FD Manual

Code Stregkodelæser CRD900FD

Læs gratis den danske manual til Code CRD900FD (2 sider) i kategorien Stregkodelæser. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Code CRD900FD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Using the CR900FD in a Universal Stand

The CR900FD has a stand detecon feature. By

default, when the CR900FD is placed in the stand,

the reader will automacally enter into moon

detecon mode. When in this mode, simply place

a bar code in the scan eld to acvate the reader.

The CR900FD will beep and ash a green LED to

indicate a ‘good read’ has occurred.

When the CR900FD is removed from the stand,

the reader switches to manual mode and the

trigger must be pressed to read a bar code.

Press and hold the CR900FD trigger, the two

blue bars eming from the reader are used for

targeng. Center the blue bars in the middle of

a bar code.

The opmal reading distance from reader to bar

code is approximately 4.0” (10 cm).

For USB Cable: plug the USB end of the Anity® cable into a USB port on the host device.

Aer several seconds, the reader will beep twice and the LED will turn o to indicate the

CR900FD is ready for use.

For RS232 Cable: plug the power supply into the AC outlet, plug the power supply cord into

the barrel jack of the cable, and connect the RS232 connector to the appropriate serial port

on the host device. Aer several seconds, the reader will beep twice and the LED will turn o

to indicate the CR1400 is ready for use.

Using the CR900FD Out of a Universal Stand

Powering on the CR900FD CR900FD Default Sengs

UPC/EAN/JAN

Code 39

Code 93

The CR900FD, out of the box, will read the following 1D bar codes:

The CR900FD can be upgraded to read 2D bar codes with the purchase of a license key. 2D

license keys can be purchased individually or as a package. Available licenses:

Conguraon Codes

Once the reader is at the opmal distance, the CR900FD will read the bar code (when the

trigger is pressed). The CR900FD will beep and ash a green LED to indicate a ‘good read’ has

occurred.

2 3

Code 128

Interleaved 2 of 5

Codabar

GS1 DataBar (RSS)

PDF417

Data Matrix

QR Code

Aztec Code

All 2D bar codes

Visit www.codecorp.com for upgrading/license key informaon.

Upgrade Opons

Note: a CR900FD will read Data Matrix conguraon codes.

The CR900FD can be quickly, and easily congured to meet the needs of dierent use cases.

A common conguraon is reading bar codes found on cell phone screens. To enable, or

disable, cell phone reading mode, scan the appropriate code below.

For more conguraon opons refer to the CR900FD Conguraon Guide located at

www.codecorp.com. For custom conguraon opons, please contact us at

support@codecorp.com.

Enable Cell Phone Reading Mode Disable Cell Phone Reading Mode

Quickstart Guide

C007258_02_CR900FD_Quickstart_Guide

Code Reader™ 900FD (CR900FD)

USB Anity® Cable RS232 Anity® Cable

w/ Power Supply

Aaching/Detaching a Cable

To aach a cable, plug the RJ-50 end of the Anity® cable into boom of the reader (Figure

1). Firmly push the connector into the reader unl a snap can be heard, to indicate the cable

is properly aached. To detach a cable, press a paper clip into the hole on the back of the

CR900FD (Figure 2), and gently pull the cable from the reader.

Figure 2Figure 1

Included with your CR900FD

Depending on the kit ordered, the following may have been shipped with your reader:

Universal Stand

Universal Stand Assembly (included when ordered as a Kit/Package)

Cleaning a CR900FD

The following agents are approved to clean a Code bar code reader:

1) Alcohol Wipes

2) CaviWipes® Disinfecng Towelees

3) Clorox® Disinfecng Wipes

4) Clorox® Bleach Soluon (10% Clorox bleach, 90% tap water)

5) Medical DiAirKem

6) Sani-Cloth® HB, Super Sani-Cloth® Germicidal, Sani-Cloth® Plus Germicidal Disposable Wipes

7) Virex® II Disinfectant Cleaner

Warranty

Code’s CR900FD carries a ve year standard warranty. Universal Stands follow the warranty

of the reader, and cables have a 90 day warranty period. For more warranty informaon,

please refer to the www.codecorp.com.

14870 S. Pony Express Rd. #200 Bluffdale, UT 84065

www.codecorp.com (801) 495-2200

Produkt Specifikationer

Mærke:	Code
Kategori:	Stregkodelæser
Model:	CRD900FD

Har du brug for hjælp?

Hvis du har brug for hjælp til Code CRD900FD stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Stregkodelæser Code Manualer

Code CR900FD Manual

2 September 2024

Code CRD900FD Manual

2 September 2024

Stregkodelæser Manualer

Nyeste Stregkodelæser Manualer

Honeywell Xenon Ultra 1962h Manual

28 September 2025

Argox AS-8250 Manual

14 September 2025

Argox AS-9500 Manual

12 September 2025

Argox AS-8312 Manual

12 September 2025

I.safe Mobile IS-TH2ER.1 Manual

10 September 2025

Newland HR23 Dorada Bluetooth Manual

6 September 2025

Newland HR23 Dorada Corded Manual

6 September 2025

Newland HR23 Dorada Manual

6 September 2025

Manhattan 154185 Manual

31 August 2025

Wasp WWR2900 Manual

30 August 2025