Creda TPRIII 1500M Manual

Creda Varmeapparat TPRIII 1500M

Læs gratis den danske manual til Creda TPRIII 1500M (4 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Creda TPRIII 1500M, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Installation and Operating Instructions
INCPUKP5RG Issue 6
TPRIII M Panel Convector Heaters
Dimensions
(millimetres)
Model s Watt A B( )
TPRIII 500M/MT 500 450 108
TPRIII 750M/MT/NC 750 620 108
TPRIII 1000M/MT/NC 1000 620 108
TPRIII 1250M/MT/NC 1250 688 108
TPRIII 1500M/MT/NC 1500 688 108
TPRIII 2000M/MT/MT7/NC 2000 860 108 Fig. 1
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by children without supervision.
Children of less than 3 years should be kept
away unless continuously supervised.
Children aged from 3 years and less than 8
years shall only switch on/off the appliance
provided that it has been placed or installed
in its intended normal operating position
and they have been given supervision or
instruction concerning use of the appliance
in a safe way and understand the hazards
involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate
and clean the appliance or perform user
maintenance.
Note that due care and consideration must
be taken when using this heater in series
with a thermal control, a program controller,
a timer or any other device that switches on
the heat automatically, since a re risk exists
when the heater is accidentally covered or
displaced.
If the supply cord is damaged it must be
replaced by the manufacturer or service
agent or a similarly qualied person in order
to avoid a hazard.
WARNING: Servicing and product
repairs should only be undertaken by the
manufacturers approved service agent or a
similarly qualied person, using only exact
manufacturer approved spare parts.
The supply circuit to the heater must
incorporate a double pole isolating switch
having a contact separation of at least 3mm.
A
150
MIN
‘x’ 150
MIN
150
MIN
B
430
Important Safety Advice
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of re, electrical shock, and
injury to persons, including the following:
IMPORTANT – The wall bracket supplied
with the appliance must be used.
WARNING – DO NOT USE THIS HEATER
IN THE IMMEDIATE SURROUNDINGS OF
A BATH, A SHOWER OR A SWIMMING
POOL.
IMPORTANT – If the heater is installed in a
room containing a bath or shower, it must be
so installed that switches and other controls
cannot be touched by a person using a bath
or shower.
Do not use outdoors.
Do not locate the heater immediately below
a xed socket outlet or connection box.
WARNING: In order to avoid overheating, do
not cover the heater. Do not place material
or garments on the heater, or obstruct the
air circulation around the heater, for instance
by curtains or furniture, as this could cause
overheating and a re risk.
NEVER cover or obstruct in any way the heat
outlet slots at the top of the heater or the air
inlet slots in the base of the heater.
The heater carries the Warning symbol
indicating that it must not be covered.
CAUTION - Some parts of this product
can become very hot and cause burns.
Particular attention has to be given where
children and vulnerable people are present.
This appliance can be used by children
aged from 8 years and above and by
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
Access to the Controls
The controls cover (see ‘x’ in Fig. 1) on your heater has a latch which
may be locked shut if desired using a small bladed screwdriver - see
Fig. 3.
To open the cover insert the blade of the screwdriver in the small
slot and rotate a quarter of a turn clockwise to disengage the latch.
The cover may then be hinged back towards the wall for access to
the controls.
Operation - Thermostat only models
Control of Output and Temperature see Fig. 4( )
The switch marked and controls the electricity supply to the heating O I
elements. The OFF position is marked .O
The switch marked - (half heat – full heat) provides a choice of I II
output as desired.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
The electrical installation must be carried out by a competent
electrician, and be in strict accordance with the current I.E.E.
regulations for Electrical Equipment in Buildings.
The heater is tted with a length of exible cable type H05VV-F size
3 x 1.0mm2 on models TPRIII 500 - 2000, for connection to the xed
wiring of the premises through a suitable connection box positioned
adjacent to the heater.
The supply circuit to the heater must incorporate a double pole isolating
switch having a contact separation of at least 3mm.
Supplementary Earth Bonding
Should Equipotential Earth Bonding be required the earthing conductor
in the supply cord is deemed to provide the supplementary bonding
connection (see Regulation 544.2.5, 17
th Edition I.E.E. Wiring
Regulations).
General
The TPR panel heater is designed for wall mounting on the brackets
supplied. It should only be operated when in the upright position as
shown.
All models are splashproof to IP24 standard.
Models TPR…MT are tted with a 24 hour programmable timer.
Model TPR…MT7 is tted with a 7 day programmable timer.
Models TPR…NC have no controls and are for use with external
thermostatic or programming controllers.
Before connecting the heater check that the supply voltage is the same
as that stated on the heater.
Please note that lit cigarettes, candles and oil burners, combined
with the convection effect of electric heaters can cause soot
deposits to build up on the surface directly above and to the sides
of the heater. This is not a fault of the heater. Extensive burning of
candles or smoking in the operating environment of this product
can produce heavy discolouration within a few months of use.
Wall Mounting
IMPORTANT – The wall brackets supplied with the appliance must
be used. The heater should be positioned observing the minimum
clearances stated around the heater - see .Fig. 1
DO NOT locate the heater immediately below a xed socket outlet
or connection box.
1. Remove wall mounting bracket from the back of the heater
by depressing the spring latch at the top of each bracket -
see .Fig. 2
255
MIN
Fig. 3
Fig. 4
Fig. 5
2. Fix the wall bracket securely to the wall through the four
screw holes provided.
3. Present the heater to the wall bracket, and engage lower
slots in the back with bracket.
4. Raise the heater to the upright position and push the heater
onto brackets to engage top latch.
Fig. 2
Thermostat Operation
The heater is tted with an adjustable thermostat enabling the room
temperature to be controlled by adjusting the setting accordingly. The *
setting represents a room temperature of approximately 5°C and may
be used for protection against frost. Higher temperature settings range
from 1-6 (max.) creating a room temperature of approximately 30°C.
A neon indicator light glows when the appliance is actually heating.
Switch on the heater and turn the thermostat knob to mark 6 opposite
the indicator mark (located on centre right of the knob - see & Fig. 4
5), and set selector switch to full heat output to warm the room rapidly.
When the room temperature has reached the desired level, turn the
thermostat knob back slowly until the thermostat just clicks off. The
heater will then maintain the room temperature at the chosen level,
provided that the correct size of heater has been selected for the
room to be heated.
NOTE – Should your heater fail to come on when the thermostat knob
is at a low setting, this may be due to the room temperature being
higher than the thermostat setting.
Operation - MT and MT7 Timer Models
Control of Output and Temperature see Fig. 5( )
The slide switch on the timer unit controls the electricity supply to the
heating elements on MT and MT7 models.
The switch marked - (half heat – full heat) provides a choice of I II
output as desired.

Produkt Specifikationer

Mærke: Creda
Kategori: Varmeapparat
Model: TPRIII 1500M

Har du brug for hjælp?

Hvis du har brug for hjælp til Creda TPRIII 1500M stil et spørgsmål nedenfor, og andre brugere vil svare dig


Varmeapparat Creda Manualer

Creda

Creda TSR18MW Manual

29 August 2024
Creda

Creda CEP1500E Manual

29 August 2024
Creda

Creda TSRE150 Manual

29 August 2024
Creda

Creda CEP2000E Manual

29 August 2024
Creda

Creda CEP075E Manual

29 August 2024
Creda

Creda COR15TS Manual

29 August 2024
Creda

Creda TPRIII 500M Manual

29 August 2024
Creda

Creda TPRIII 1500M Manual

29 August 2024
Creda

Creda EPH500 Manual

29 August 2024
Creda

Creda EPH1500 Manual

29 August 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

N'oveen

N'oveen CH9000 Manual

1 August 2025
N'oveen

N'oveen FH-03 Manual

1 August 2025
Emos

Emos ZU133 Manual

1 August 2025
Emos

Emos ZT1521E Manual

31 Juli 2025
ProfiCare

ProfiCare PC-GKH 3119 Manual

31 Juli 2025
Meaco

Meaco Heat Motion Eye 1.8kW Manual

31 Juli 2025
Emos

Emos ZT1621E Manual

31 Juli 2025
Emos

Emos ZU166 Manual

31 Juli 2025
ProfiCare

ProfiCare PC-GKH 3118 Manual

31 Juli 2025
Cecotec

Cecotec Readywarm 9820 Force Dual Manual

31 Juli 2025