Cres Cor IFW-63-10 Manual

Cres Cor Lys IFW-63-10

Læs gratis den danske manual til Cres Cor IFW-63-10 (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Cres Cor IFW-63-10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION INSTRUCTIONS

for PULL-DOWN INFRA RED MODELS IFW-63 SERIES

5925 Heisley Road • Mentor, OH 44060-1833

Infra-red Lamps

IFW 63 Series

FL-2219

Rev. 2 (05/06) Page 1 of 2

Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com

ELECTRICAL SPECS:

VOLTS WATTS AMPS HERTZ PHASE NEMA

120 250 2.0 60 1 5-15

240 275 1.1 60 1 6-15

Warmer should be installed by an experienced

electrician.

U.L. and CSA REQUIREMENTS:

A. Wires of warmers to be connected to 75°C wire.

B. Wires are to be installed in conduit.

C. Warmers are not to be installed any closer than 1” from

a wall.

D. Warmers must be at least 16” above a combustible

surface.

HOW TO INSTALL: (See ﬁ gure at right)

NOTE: Outlet box (7) and screws (5) are to be furnished by

customer.

Pull canopy (2) down over coil cord.

Attach ground wire from ceiling to the “GND” hole in

the plate (4) with screw (6).

Wire the warmer leads to the outlet box (7) leads.

Attach plate (4) to the outlet box (7) with screws (5).

Lower or raise the coil cord to the height you want.

Adjust the tension of the coil cord in the slot as shown.

(a) To increase tension, turn slot clockwise.

(b) To decrease tension, turn slot counter clockwise.

7. Pull up canopy (2) and screw it to the plate (4) with two

machine screws (3).

8. Screw lamp into socket.

DO NOT PULL

DOWN ON CORD

BEYOND THE STOP.

Adjust Coil

Tension

INSTALLATION INSTRUCTIONS

for PULL-DOWN INFRA RED MODELS IFW-63 SERIES

5925 Heisley Road • Mentor, OH 44060-1833

Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com

Infra-red Lamps

IFW 63 Series

FL-2219

Rev. 2 (05/06) Page 2 of 2

HOW TO INSTALL HOOD:

You will need a Phillips head (preferably magnetic)

screwdriver with a long neck.

Slide the hole in the top of the hood over the socket.

Look inside of the hood and line up two (2) hood

mounting holes with the holes in the arm assembly.

Put the screw provided on the screwdriver tip and

screw loosely into one hole and then into the other;

then tighten both screws.

Screw lamp into the socket.

REPLACEMENT PARTS:

DESCRIPTION CMP No.

Lamp, Red (120V) 0820-001

Lamp, White (120V) 0820-033

Lamp, Red (240V) 0820-014

Socket 0822-037

Switch (120V) 0808-002

Switch (240V) 0808-122

Reel/Pulley Assembly 1287-084

Coil Cord (IFW 63) 0834-006

Coil Cord (IFW 63L) 0834-007

Produkt Specifikationer

Mærke:	Cres Cor
Kategori:	Lys
Model:	IFW-63-10

Har du brug for hjælp?

Hvis du har brug for hjælp til Cres Cor IFW-63-10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Cres Cor Manualer

Cres Cor IFW-63-10 Manual

17 September 2025

Cres Cor IFW-64-10-PN Manual

17 September 2025

Cres Cor IFW-66-10-PN Manual

17 September 2025

Cres Cor IFW-63-10-R Manual

17 September 2025

Cres Cor IFW-66-10-R Manual

16 September 2025

Cres Cor IFW-64-10-R Manual

25 August 2025

Cres Cor IFW-63-10-PN Manual

25 August 2025

Cres Cor IFW-63-10-PB Manual

25 August 2025

Lys Manualer

Nyeste Lys Manualer

Flex WL 2800 18.0 Manual

17 September 2025

Flex TL 4000 18.0/230 Manual

17 September 2025

Flex DWL 2500 10.8/18.0 Manual

17 September 2025

Unilux Baya Bamboo Manual

17 September 2025

Ikea SPIKEN 904.337.25 Manual

17 September 2025

Ikea SOLBO 603.478.47 Manual

17 September 2025

Unilux Jazz Manual

17 September 2025

Ikea ANKARSPEL 405.242.71 Manual

17 September 2025

Ikea TRÅDFRI 405.233.75 Manual

17 September 2025

Unilux Linka Manual

17 September 2025