Crestron CAEN-4X2 Manual

Crestron Ikke kategoriseret CAEN-4X2

Læs gratis den danske manual til Crestron CAEN-4X2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Crestron CAEN-4X2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
CAEN
Automation Enclosures
Installation Guide
Description
The Crestron
®
CAEN Series of automation enclosures are designed to house Crestron
lighting shade control devices. CAEN enclosures are available in an assortment of sizes,
suitable for surface or ush wall-mount installation. Each model has been engineered to
and electrical knockouts.
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information and the latest rmware updates. Use a QR
reader application on your mobile device to scan the QR image.
Dimensions
The overall dimensions for the CAEN enclosures are shown in the following illustration and
table.
NOTE: The PAC2 occupies two module spaces in a double-wide enclosure and one
module space in a single-wide.
NOTE: Four keyholes are located within the enclosure and should be used for surface
mounting.
CAEN Overall Dimensions (Front and Side Views)
W3
W4
W1
W2
H2
W3
H1 H3
D1
W3 W5
W6
Dimensions
DIMENSIONS CAEN-7X2 CAEN-7X1 CAEN-4X2 CAEN-4X1 CAEN-2x1 CAEN-1x1
H1 62 in
(1575 mm)
62 in
(1575 mm)
38-7/8 in
(987 mm)
38-7/8 in
(987 mm)
23-1/2 in
(596 mm)
16-9/16 in
(421 mm)
H2 2-11/16 in
(69 mm)
2-11/16 in
(69 mm)
2-11/16 in
(69 mm)
2-1/8 in
(53 mm)
2-1/8 in
(53 mm)
2-1/8 in
(53 mm)
H3 56 in
(1422 mm)
56 in
(1422 mm)
32-7/8 in
(835 mm)
34 in
(863 mm)
18-5/8 in
(473 mm)
10-7/8 in
(277 mm)
W1 26-1/2 in
(673 mm)
15-3/8 in
(390 mm)
26-1/2 in
(673 mm)
15-3/8 in
(390 mm)
15-3/8 in
(390 mm)
15-3/8 in
(390 mm)
W2 25-1/2 in
(648 mm)
14-3/8 in
(365 mm)
25-1/2 in
(648 mm)
14-3/8 in
(365 mm)
14-3/8 in
(365 mm)
14-1/4 in
(362 mm)
W3 2-1/2 in
(64 mm)
1-3/4 in
(45 mm)
2-1/2 in
(64 mm)
1-3/4 in
(45 mm)
1-3/4 in
(45 mm)
1-11/16 in
(43 mm)
W4 20-1/2 in
(520 mm)
10-7/8 in
(276 mm)
20-1/2 in
(521 mm)
10-7/8 in
(276 mm)
10-7/8 in
(276 mm)
10-7/8
(276 mm)
W5
1
20-1/2 in
(521 mm)
9-7/8 in
(250 mm)
20-1/2 in
(521 mm)
9-7/8 in
(250 mm)
9-7/8 in
(250 mm)
9-7/8 in
(250 mm)
W6 2-1/2 in
(64 mm)
2-3/4 in
(69 mm)
2-1/2 in
(64 mm)
2-3/4 in
(69 mm)
2-3/4 in
(69 mm)
2-3/4 in
(69 mm)
D1 4-3/16 in
(107 mm)
4-3/16 in
(107 mm)
4-3/16 in
(107 mm)
4-1/16 in
(103 mm)
4-3/16 in
(107 mm)
4-3/16 in
(107 mm)
Cover
Thickness
1/16 in
(1 mm)
1/16 in
(1 mm)
1/16 in
(1 mm)
1/16 in
(1 mm)
1/16 in
(1 mm)
1/16 in
(1 mm)
Cover Height 62-3/4 in
(1593 mm)
62-3/4 in
(1593 mm)
39-5/8 in
(1006 mm)
39-5/8 in
(1006 mm)
24-1/4 in
(615 mm)
16-9/16 in
(421 mm)
Cover Width 27-1/4 in
(692 mm)
16-1/8 in
(409 mm)
27-1/4 in
(692 mm)
16-1/8 in
(409 mm)
16-1/8 in
(409 mm)
16-1/8 in
(409 mm)
Weight
(empty)
2
65 lb
(29.5 kg)
42 lb
(19.1 kg)
43 lb
(19.5 kg)
28 lb
(12.7 kg)
19 lb
(8.6 kg)
14 lb
(6 kg)
Maximum
Weight (lled)
200 lb
(90.8 kg)
100 lb
(45.4 kg)
100 lb
(45.4 kg)
55 lb
(24.9 kg)
31 lb
(14.1 kg)
26 lb
(11.8 kg)
1. The lower keyholes are not symmetrically spaced within single-wide enclosures.
2. Weight (empty) is the weight of an empty enclosure with cover.
Installation
A licensed electrician must mount the enclosure in accordance with all national and local
codes. Refer to the table for the weight of a fully loaded enclosure.
When choosing components to place in the enclosure, refer to the table to ensure that
the maximum weight capacity is not exceeded. Each component’s product page on the
Crestron website lists the component’s weight.
Use the screw holes shown in the “Mounting Details” diagrams to mount the CLT-series
terminal blocks. Install shade control devices and accessories according to their installation
guides.
CAUTION: These enclosures house equipment that needs to be air-cooled. Therefore,
mount in a well-ventilated area. The ambient temperature range should be 32°F to 104°F
(0°C to 40°C). The relative humidity should range from 10% to 90% (non-condensing).
Furthermore, allow adequate clearance in front of the vented cover for servicing and
ventilation.
NOTE: Unless otherwise indicated, the system specied in this guide is modular,
requiring assembly in the eld by a licensed electrician, in accordance with all national
and local codes.
If a UL Listed panel is required, Crestron offers this service through its UL Listed panel
shop. This includes complete in-factory system conguration and assembly by Crestron
for an additional fee.
NOTE: Install components into the lowest available spaces and continue toward the top
of the enclosure.
NOTE: Enclosures are intended for indoor use only.
NOTE: When ush mounting, 5/8 in (16 mm) drywall is preferred.
Wiring
Class 1 and Class 2 eld wires must be kept separate. Refer to the following illustrations
showing single-wide and double-wide wiring details. Areas for high-voltage (Class 1) wiring
are shown along the top and side(s) of the unit. The lower area is reserved for low-voltage
(Class 2) wiring.
CAUTION: All power feeds must be protected by 15- or 20-amp circuit breakers (not
included).
NOTE: Use copper conductors only – rated 60°C.
NOTE: Install all wiring in accordance with all local and national electrical codes.
NOTE: Two snap bushings are supplied. If required, insert the bushings into the
knockouts at the bottom of the enclosure to prevent damage to low-voltage wiring.
Tighten all CLT-series terminal block screws and grounding terminal block screws to the
torque specied in the “Torque Data” table.
CAUTION: Failure to properly tighten the screws may result in poor electrical
connection and overheating of the terminals.
Torque Data
CLT TERMINAL
BLOCKS
GROUNDING TERMINAL BLOCKS
Wire Range 22-10 14-10 8 6-4
Torque (in-lb) 9 35 40 45
Below are typical products in a CAEN enclosure:
• CLX-series modules
• CLT-series terminal blocks
• CSA-PWS-TBLOCK-2 and CSA-PWS-TBLOCK-3 terminal block for shades
• CSA-PWS10S-HUB-ENET power supply for shades
• CAEN-BLOCK terminal block
• PAC2M processor
• Grounding terminal block
Mounting Details - Single-Wide CAEN
Mount CLT
to these holes.
Mount CLX
to these holes.
Wiring Details - Single-Wide CAEN
Class 1 wiring only
Class 2 wiring only
Mounting Details - Double-Wide CAEN
Mount CLX
to these holes.
Mount CLT
to these
holes.
Wiring Details - Double-Wide CAEN
Class 1 wiring
only
Class 2 wiring only
This product is Listed to applicable UL
®
Standards and requirements tested by Underwriters
Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters
Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specic information, please visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics,
Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or registered
trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in
the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.
Crestron Electronics, Inc. Installation Guide - DOC. 5940F
15 Volvo Drive Rockleigh, NJ 07647 (2002052)
Tel: 888.CRESTRON 07.17
Fax: 201.767.7576 Specications subject to
www.crestron.com change without notice.

Produkt Specifikationer

Mærke: Crestron
Kategori: Ikke kategoriseret
Model: CAEN-4X2

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CAEN-4X2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Crestron Manualer

Crestron

Crestron FT2-700-ELEC-PTL Manual

30 Juli 2025
Crestron

Crestron RMK-AMP-X Manual

30 Juli 2025
Crestron

Crestron DIN-GWDL-SPLTR Manual

30 Juli 2025
Crestron

Crestron HD-CTL-101 Manual

30 Juli 2025
Crestron

Crestron FT2-202-ELEC-PTL Manual

30 Juli 2025
Crestron

Crestron STIRP Manual

30 Juli 2025
Crestron

Crestron CSP-LIR-USB Manual

30 Juli 2025
Crestron

Crestron CEN-IO-COM-202 Manual

30 Juli 2025
Crestron

Crestron CEN-IO-DIGIN-204 Manual

29 Juli 2025
Crestron

Crestron DIN-DLI Manual

29 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock

Hozelock 5102 Manual

2 August 2025
ART

ART 310 Manual

2 August 2025
Gorenje

Gorenje KAS53ZDCINVFT Manual

2 August 2025
Gorenje

Gorenje KAS35ZDCINVFT Manual

2 August 2025
Navman

Navman MY450LMT Manual

2 August 2025
Navman

Navman MiVue 745 Manual

1 August 2025
Hitachi

Hitachi WR22SE Manual

1 August 2025
Synology

Synology M2D20 Manual

1 August 2025
Fluke

Fluke FibertLert-125 Manual

1 August 2025
Buffalo

Buffalo GC882 Manual

1 August 2025