Crestron CLT-1FAN4 Manual

Crestron Ikke kategoriseret CLT-1FAN4

Læs gratis den danske manual til Crestron CLT-1FAN4 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Crestron CLT-1FAN4, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
CLT-1FAN4/CLX-1FAN4
Terminal Block and Module
Installation Guide
Description
The Crestron
®
1-Feed, 4-Fan Terminal Block and Module (CLT-1FAN4 and CLX-1FAN4,
respectively), are considered a single entity and must be used together. They ship
separately to permit termination of the eld wiring to the CLT-1FAN4 prior to installation of
control that connects to the terminal block and controls four ceiling fan motors. The
maximum load is 2 amps for any controlled circuit. The module requires 120 Vac 60 Hz,
1 phase input voltage. The terminal block and module can be mounted in any Crestron
Automation Enclosure (CAEN-Series Enclosures). The terminal block is designed to
terminate the circuit feed ( and ) and distribute the controlled circuit to the LINE NEUTRAL
fan(s) ( ). An oversize heat sink dissipates heat efciently. There are LEDs on the LOAD
module to indicate communication to a Cresnet
®
network, input power to the module, and
output power to the ceiling fan motors.
NOTE: This module is for speed control of a ceiling fan (paddle fan) only. The
CLX-1FAN4 cannot change the fan direction. The module provides four speed settings
as well as turning the fan off.
NOTE: This module cannot control fans with remote-controlled integrated speed
controls.
The CLT-1FAN4 terminal and CLX-1FAN4 module are shown in the following illustrations.
CLT-1FAN4 Terminal Block with Left- and Right-Side CLX-1FAN4 Labels
Installation
WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker or
fuse, and test that the power is off before wiring!
NOTES: Observe the following points:
• This product must be installed and used in accordance with appropriate electrical
codes and regulations.
• This product must be installed by a electrician.licensed
• Sensors must be mounted on a vibration-free surface.
NOTE: Before using the CLX-1FAN4, ensure the device is using the latest rmware.
Check for the latest rmware for the CLX-1FAN4 at www.crestron.com/rmware.
Firmware is loaded onto the device using Crestron Toolbox™.
The terminal block and module must be mounted into a Crestron Automation Enclosure by
a licensed electrician, in accordance with all national and local codes.
CAUTION: This equipment is for indoor use only and needs to be air-cooled. Mount in a
well-ventilated area. The ambient temperature must be 32°F to 104°F (0°C to 40°C). The
relative humidity must be 0% to 90% (non-condensing).
Terminal blocks are installed along the left side of single-wide enclosures and along the
outside edges (left and right sides) of double-wide enclosures. Modules are installed along
the right side of single-wide enclosures and side-by-side in the center of double-wide
enclosures. When installing modules and terminal blocks in a double-wide enclosure, be
sure to invert units on the right side so that they can be properly wired. Refer to the
illustrations below when considering the location of terminal blocks and modules within an
enclosure.
NOTE: Modules and terminal blocks must be installed into the lowest available spaces
and continue toward the top of the enclosure.
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
• Do not use outdoors.
• Do not mount near gas or electric heaters.
• Equipment should be mounted in locations and at heights where it will not be
subjected to tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause
an unsafe condition.
• Do not use this equipment for other than its intended use.
• All servicing should be performed by qualied service personnel.
• If any Emergency Circuits are fed or controlled from this panel, it must be located
electrically where fed from a UPS, generator, or other guaranteed source of power
during emergency and power outage situations.
SAVE THESE INSTRUCTIONS.
Terminal Block and Module Locations (Single-Wide Enclosure)
Terminal Block and Module Locations (Double-Wide Enclosure)
NOTE: Unless otherwise indicated, the lighting system specied in this guide is modular,
requiring assembly in the eld by a licensed electrician in accordance with all national and
local codes.
If an assembled UL Listed panel is required, it can be obtained through Crestron’s UL
Listed panel shop. This includes complete in-factory system conguration and assembly
by Crestron for an additional fee.
Terminal Block Installation and Field Wiring
Apply the supplied adhesive label before installing the terminal block. The adhesive label
provides the labeling for each terminal in the terminal block and is designed to accomodate
installation into the left or right side of a cabinet.
NOTE: Both left-side and right-side adhesive wiring labels are provided. The left-side
labels are used in both single- and double-wide enclosures. The right-side labels are used
only in double-wide enclosures.
1. Remove the backing from the left- or right-side adhesive wiring label.
2. Apply the adhesive label by aligning the holes in the label with the holes on the
Crestron Automation Enclosure where the terminal block is to be mounted. The wiring
label lies beneath the terminal block as shown in the following diagrams.
3. Use the two supplied self-tapping Phillips pan head screws (8B x 1/4 inch length) to
secure the terminal block to the Crestron Automation Enclosure.
CAUTION: Bypass jumpers are provided to test circuits and to protect the module during
installation. When properly secured by the ve screws, the jumper on the black and red
section of the terminal block shorts the LINE to FAN so that the circuit is energized. Do
not remove any bypass jumpers until all feed and load wiring has been completed, the
circuit has been tested for electrical faults, and the module has been installed. Refer to
“Module Installation.”
Furthermore, the jumper on the white section of the terminal block ties the neutral in to
the neutral out. These jumpers should never be removed.
NOTE: Use copper conductors only—rated 75° C or greater.
4. Turn off the circuit breakers.
5. Connect the circuit feed (line and neutral) and controlled circuit (load) wires to the
terminal block per the markings provided on the wiring label (as shown in the following
diagrams). Terminal blocks accept one 14–10 AWG wire. Strip the wires to 1/2 inch
(13 millimeters). Tighten terminal blocks to 9 in-lbs.
6. Terminate the ground wires at the grounding terminal blocks that are available in the
cabinet. Tighten the grounding terminal blocks to 35 in-lbs (14–10 AWG), 40 in-lbs
(8 AWG), or 45 in-lbs (6–4 AWG).
7. Test each circuit for electrical faults by turning on the circuit breaker and checking
that the breaker does not trip and that power is delivered to the proper loads.
Wiring the Terminal Block to the Feed and Load(s)
Module Installation
CAUTION: The module contains electrostatic sensitive devices (ESDs); the unit must be
handled from the metal chassis. Do not touch the PC board or components.
Install the modules after the terminal blocks are installed and the enclosure has been
completely wired.
1. Use the four supplied self-tapping Phillips pan head screws (8B x 1/4-inch length) to
secure the module to the enclosure.
2. As shown in the previous wiring diagram, connect the wires from the module to the
terminal block. Each wire exits the module directly in line with, and is the same color
as, the terminal to which it should be connected. Wires are prestripped to 1/2 inch
(13 millimeters). Tighten to 9 in-lbs.
3. If the module is being installed above another module within the enclosure, attach
the supplied module interconnect cable to the two modules. The illustration that
follows shows the area within a double-wide enclosure where the corners of four
modules meet.
NOTE: One wire on the module interconnect cable may be a different color from
the rest. The color has no bearing on its orientation during installation.
Use Module Interconnect Cable to Wire Module to Module
Ground Bus CLT-1FAN4
Terminal Block
CLX-1FAN4
Module
CLX-1FAN4
FAN 1
F
F
F 4
LINE
1 F EED
4 F AN
120VAC 60 Hz
8A MAX
2A MAX/CKT
N IN
N OU T 1
N OU T 2
N OU T 3
N OU T 4
Line
Connection from a 15
or 20 Amp Circuit
Breaker
Bypass
Jumpers
Terminal
Block
To
Loads(s)
Left-Side
Wiring Label
Ground
Bus
Module
Location
Label
Neutral
Ground
CLX-1FAN4
FAN 1
FAN 2
FAN 3
FAN 4
LINE
1 FEED
4 FAN
120VAC 60 Hz
8A MAX
2A MAX/CKT
N IN
N OUT 1
N OUT 2
N OUT 3
N OUT 4
CLX-1FAN4
FAN 4
FAN 3
FAN 2
FAN 1
LINE
1 FE ED
4 FA N
120VAC 60 Hz
8A MAX
2A MAX/CKT
N OUT 4
N OUT 3
N OUT 2
N OUT 1
N IN
CLX-1FAN4
FAN 1
FAN 2
FAN3
FAN 4
LINE
1 FE ED
4 FA N
120VAC 60 Hz
8A MAX
2A MAX/CKT
N IN
N OUT 1
N OUT 2
N OUT 3
N OUT 4
CLX-1FAN4 Module (Connects to a CLT-FAN4)
Module Interconnect
Cable Attached
Connection Not
Made
Ground Bus CLT-1FAN4
Terminal Block
CLX-1FAN4
Module
CLX-1FAN4
FAN 1
F
F
F 4
LINE
1 FE ED
4 FA N
120VAC 60 Hz
8A MAX
2A MAX/CKT
N IN
N OUT 1
N OUT 2
N OUT 3
N OUT 4
CLX-1FAN4
FAN 4
F
F
F 1
LINE
1 FE ED
4 FA N
120VAC 60 Hz
8A MAX
2A MAX/CKT
N OUT 4
OUT
N OUT 2
N OUT 1
N IN
Ground BusCLT-1FAN4
Terminal Block
CLX-1FAN4
Module
Line
Connection from a 15
or 20 Amp Circuit
Breaker
Bypass
Jumpers
Terminal
Block
To
Loads(s)
Right-Side
Wiring Label
Ground
Bus
Module
Location
Label
Neutral
Ground
CLX-1FAN4
FAN 4
FAN 3
FAN 2
FAN 1
LINE
1 FEED
4 FAN
120VAC 60 Hz
8A MAX
2A MAX/CKT
N OUT 4
N OUT 3
N OUT 2
N OUT 1
N IN
Additional Resources
Visit the product page on the Crestron website
(www.crestron.com) for additional information
and the latest rmware updates. Use a QR
reader application on your mobile device to scan
the QR image.
CLT-1FAN4 CLX-1FAN4

Produkt Specifikationer

Mærke: Crestron
Kategori: Ikke kategoriseret
Model: CLT-1FAN4

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CLT-1FAN4 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Crestron Manualer

Crestron

Crestron HZ2-BTNS-5 Manual

7 Oktober 2025
Crestron

Crestron HZ2-AUX Manual

7 Oktober 2025
Crestron

Crestron PW-2407WUL Manual

29 September 2025
Crestron

Crestron C2N-UNI8IO Manual

28 September 2025
Crestron

Crestron CLXI-4HSW4 Manual

24 September 2025
Crestron

Crestron GLD-LED-50W Manual

24 September 2025
Crestron

Crestron TPS-4LW Manual

23 September 2025
Crestron

Crestron Zūm Manual

23 September 2025
Crestron

Crestron SIMPL Manual

23 September 2025
Crestron

Crestron UC-FCM-T Manual

23 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

RADEMACHER

RADEMACHER Troll Comfort-3D 5635 Manual

1 November 2025
Beverage-Air

Beverage-Air VueMax VMHC-7-1-B Manual

1 November 2025
SmallRig

SmallRig 4842 Manual

1 November 2025
Ikea

Ikea TALGJE 702.982.38 Manual

1 November 2025
Lindy

Lindy 43339 Manual

1 November 2025
Ikea

Ikea VINTERFINT 805.800.24 Manual

1 November 2025
RADEMACHER

RADEMACHER RolloTron Schwenkwickler Comfort 1500 Manual

1 November 2025
Lantronix

Lantronix ION C2110 Manual

1 November 2025
Wiesenfield

Wiesenfield WIE-CHP-110 Manual

1 November 2025
Ikea

Ikea KLOTTHUJA 105.506.76 Manual

1 November 2025