Crestron CLT-1MC4 Manual

Crestron Ikke kategoriseret CLT-1MC4

Læs gratis den danske manual til Crestron CLT-1MC4 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Crestron CLT-1MC4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CLT-1MC4/CLX

-1MC4

Terminal Block and Motor Control Module

Installation Guide

Description

The Crestron

1-feed, 4-motor terminal block and module (CLT-1MC4 and CLX-1MC4,

respectively) are considered a single entity and must be used together. They ship

separately to permit termination of the eld wiring to the CLT-1MC4 prior to installation of

the CLX-1MC4. They can be mounted in any Crestron Automation Enclosure

(CAEN-Series Enclosures). The terminal block is designed to terminate the circuit feed

(LINE and NEUTRAL) and distribute the controlled circuits (LOAD) to the motors. The

module connects to the terminal block and controls four bidirectional motors. The

maximum load is 10 Amps (1/2 HP) for any controlled circuit, limited to 16 amps total per

module. The unit requires 120 Vac 50/60 Hz, 1 phase input voltage. An oversize heat sink

dissipates heat efciently. There are LEDs on the module to indicate communication to a

Cresnet

network, input power to the module, and output power to the load.

Installation

WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker or

fuse, and test that the power is off before wiring!

CAUTION: This equipment is for indoor use only and needs to be air cooled. Mount in a

well-ventilated area. The ambient temperature must be 32°F to 104°F (0°C to 40°C). The

relative humidity must be 0% to 90% (noncondensing).

NOTES: Observe the following points:

• This product must be installed and used in accordance with appropriate electrical

codes and regulations.

• This product must be installed by a licensed electrician.

NOTE: Before using the CLX-1MC4, ensure the device is using the latest rmware.

Check for the latest rmware for the CLX-1MC4 at www.crestron.com/rmware.

Firmware is loaded onto the device using Crestron Toolbox™ software.

The terminal block is installed along the left side of single-wide enclosures and along the

outside edges (left and right sides) of double-wide enclosures. The module is installed

along the right side of single-wide enclosures and side-by-side in the center of

double-wide enclosures. When installing modules and terminal blocks in a double-wide

enclosure, be sure to invert units on the right side so that they can be properly wired.

Refer to the illustrations when considering the location of terminal blocks and modules

within an enclosure.

NOTE: The CLT-1MC4 and CLX-1MC4 must be installed into the lowest available

spaces of the enclosure rst and then continue toward the top of the enclosure.

Terminal Block and Module Locations (Single-Wide Enclosure)

Additional Resources

Visit the product page on the Crestron website

(www.crestron.com) for additional information

and the latest rmware updates. Use a QR

reader application on your mobile device to scan

the QR image.

NOTE: If an assembled UL

Listed panel is required, it can be obtained through

Crestron’s UL Listed panel shop. An assembled UL Listed panel includes complete

in-factory system conguration and assembly by Crestron for an additional fee.

Terminal Block Installation and Field Wiring

Apply the supplied adhesive label before installing the terminal block. The adhesive label

provides identication for each terminal in the terminal block and is designed to

accomodate installation into the left or right side of the enclosure.

NOTE: Both left-side and right-side adhesive wiring labels are provided. The left-side

labels are used in both single- and double-wide enclosures. The right-side labels are

used only in double-wide enclosures.

1. Remove the backing from the left- or right-side adhesive wiring label.

2. Apply the adhesive label by aligning the holes in the label with the holes on the

Crestron Automation Enclosure where the terminal block is to be mounted. The

wiring label lies beneath the terminal block as shown in the following diagrams.

3. Use the two supplied self-tapping Phillips pan head screws (8B x 1/4-inch length) to

secure the terminal block to the Crestron Automation Enclosure.

CAUTION: The jumper on the white section of the terminal block ties the neutral

in to the neutral out. These jumpers should never be removed.

NOTE: Use copper conductors only—rated 75° C or greater.

4. Turn off the circuit breakers.

5. Connect the circuit feed (LINE and NEUTRAL) and controlled circuit (LOAD) wires to

the terminal block per the markings provided on the wiring label (as shown in the

following diagrams). Terminal blocks accept one 14–10 AWG wire. Strip the wires to

1/2 in (13 mm). Tighten terminal blocks to 9 in-lbs.

NOTE: Only one motor may be wired per circuit.

6. Terminate the ground wires at the grounding terminal blocks that are available in the

enclosure. Tighten the grounding terminal blocks to 35 in-lbs (14–10 AWG), 40 in-lbs

(8 AWG), or 45 in-lbs (6–4 AWG).

7. Test the circuit for electrical faults by connecting LINE to OPEN 1. Switch on the

circuit breaker, and check that it does not trip and that the load connected to

OPEN 1 is receiving power. Switch off the circuit breaker, remove the connection

between LINE and OPEN 1, and repeat this step, for CLOSE 1, and then sequentially

for each OPEN and CLOSE motor connection.

Wiring the Terminal Block to the Feed and Load(s)

(Single-Wide and Left-Side Double-Wide Enclosures)

Terminal Block and Module Locations (Double-Wide Enclosure)

CLX-1MC4

OPEN 3

CLOSE 3

OPEN 4

CLOSE 4

1 FEED

4 MOTOR

CONTROL

120VAC 60 Hz

16A MAX

N IN

N OUT 1

N OUT 2

N OUT 3

N OUT 4

OPEN 1

CLOSE 1

OPEN 2

CLOSE 2

LINE

Line

Connection from a 15

or 20 Amp Circuit

Breaker

Jumper

Terminal

Block

Left-Side

Wiring Label

Module

Location

Label

Neutral

Grounding

Terminal

Block

Ground

Motor 4

Motor 3

Motor 2

Motor 1

Grounding

Terminal

Block

CLT-1MC4

Terminal Block

(Left)

CLX-1MC4

Module

CLT-1MC4

Terminal Block

(Right)

CLX-1MC4

Module

Grounding

Terminal

Block

CLX-1MC4

1 FE ED

4 MO TOR

CONT ROL

120VAC 60 Hz

16A MAX

N OUT 4

N OUT 3

N OUT 2

N OUT 1

N IN

LINE

CLOSE 2

C O 1

OP 1

CLOSE 4

OP 4

C O 3

OP 3

CLX-1MC4

OPEN 3

C O 3

OP 4

C O 4

1 FE ED

4 MO TOR

CONT ROL

120VAC 60 Hz

16A MAX

N IN

N OUT 1

N OUT 2

N OUT 3

N OUT 4

OPEN 1

C O 1

OP 2

C O 2

LINE

CLX-1MC4

OPEN 3

C O 3

OP 4

C OS 4

1 F EED

4 M OTOR

CON TROL

120VAC 60 Hz

16A MAX

N IN

N OU T 1

N OU T 2

N OU T 3

N OU T 4

OPEN 1

C OS 1

OP 2

C OS 2

LINE

CLT-1MC4 Terminal Block

CLX-1MC4 Module

Grounding Terminal Block

CLT-1MC4

CLX-1MC4

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	CLT-1MC4

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CLT-1MC4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crestron Manualer

Crestron HZ2-BTNS-5 Manual

7 Oktober 2025

Crestron HZ2-AUX Manual

7 Oktober 2025

Crestron PW-2407WUL Manual

29 September 2025

Crestron C2N-UNI8IO Manual

28 September 2025

Crestron CLXI-4HSW4 Manual

24 September 2025

Crestron GLD-LED-50W Manual

24 September 2025

Crestron TPS-4LW Manual

23 September 2025

Crestron Zūm Manual

23 September 2025

Crestron SIMPL Manual

23 September 2025

Crestron UC-FCM-T Manual

23 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hendi 551813 Manual

2 November 2025

BougeRV E50 Manual

2 November 2025

Beverage-Air VueMax VMHC-7-1-G Manual

2 November 2025

OneConcept Magic-Carpet DX Manual

2 November 2025

Tonor T20 Manual

2 November 2025

Beverage-Air Horizon HRP3HC-1HS Manual

2 November 2025

Workzone AB1600 Manual

2 November 2025

Homedics BH-100-AU Manual

2 November 2025

Beverage-Air Horizon HFP1HC-1S Manual

2 November 2025

Beverage-Air VueMax VMHCSL-18-1-B Manual

2 November 2025