Crestron CSAI-PWS40 Manual

Crestron Ikke kategoriseret CSAI-PWS40

Læs gratis den danske manual til Crestron CSAI-PWS40 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Crestron CSAI-PWS40, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
The CSA-PWS40 and CSAI-PWS40 are outlet-mountable, 40 W, 24 VDC regulated power
packs that provide power for Crestron® CSM-QMTDC series roller shade or drapery track
motors. The CSA-PWS40 has a NEMA 1-15P blade insert installed and the
CSAI-PWS40 ships with a blade insert kit that consists of eight blade inserts.
The CSA-PWS40 and CSAI-PWS40 are ideally suited to provide local power for
CSM-QMTDC motors that communicate using the infiNET EX® network.
Check the Box
Item Qty
CSA-PWS40 or CSAI-PWS40 1
CSAI-PWS40 Only
Dimensions
2.91 in.
(74 mm)
2.21 in.
(56 mm)
1.71 in.
(43 mm)
1.54 in.
(39 mm)
Install the Power Pack
NOTES:
• Install and use this product in accordance with appropriate electrical codes and
regulations.
• An AC outlet must be located near the CSM-QMTDC series roller shade or drapery
track motor that is powered by the power pack. The power pack has an 8 ft (2.43 m)
long power cable.
Install the power pack:
1. Connect the flying leads from the power pack to the flying leads on the CSM-QMTDC
series roller shade or drapery track motor. Ensure that connections are properly made.
NOTE: To change the plug type on the CSAI-PWS40, refer to the “Change the Blade
Insert” section on the next page.
2. Plug the power pack into a 120 VAC power outlet.
Wiring Diagram Using a Cresnet Motor
Power Pack
24
Y
Z
G
To Cresnet
Motor
pigtail
24G
Z Y
G
Cresnet motor
Wiring Diagram Using an infiNET EX Motor
24
G
Motor
pigtail
24G
infiNET EX motor
Power Pack
CSA-PWS40/CSAI-PWS40
Power Pack for Crestron® CSM-QMTDC Series Roller Shade and Drapery Track Motors
Change the Blade Insert (CSAI-PWS40 Only)
1. If a blade insert is attached to the CSAI-PWS40, slide the spring-loaded locking key
downward and then pull upward on the blade insert to remove it.
2. Insert the top edge of the blade assembly into the top of the CSAI-PWS40 at
a 30-60 degree angle.
NOTE: The top edge of the blade assembly is flat, and the bottom edge is U-shaped.
The CSAI-PWS40 is shaped similarly.
3. Push the blade insert down into the CSAI-PWS40 until it locks into place. A clicking
sound will occur.
4. Pull up on the blade to check that the blade insert is securely installed.
Technical Specifications
Refer to the CSA-PWS40 product page at for a complete list of product www.crestron.com
specifications.
Specification Details
Output Rating 24 VDC, 40 W (1.66 A), regulated
Power Requirements 1 A @ 100-240 VAC, 50/60 Hz
Connections
Line
Load
(1) power plug, line power input
(1) 8 ft (2.43 m) attached cable with inline ferrite core and
flying leads
Construction 94V-0 polycarbonate, white, outlet-mountable
Environmental
Temperature
Humidity
32º to 104ºF (0º to 40ºC)
15% to 95% RH (noncondensing)
Weight 6.4 oz (182 g)
Additional Information
Scan or click the QR code for detailed product information.
CSA-PWS40 CSAI-PWS40
Compliance and Legal
Original Instructions: The U.S. English version of this document is the original instructions. All other languages are a
translation of the original instructions.
As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.
This product is listed to applicable UL® Standards and requirements tested by Intertek® services.
Ce produit est homologué selon les normes et les exigences UL applicables par Intertek Prestations de service.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may
not cause harmful interference and (2) this device must accept any interference received, including interference that may
cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, and infiNET EX are either trademarks or registered trademarks of Crestron Electronics, Inc.
in the United States and/or other countries. The ETL logo is either a trademark or registered trademark of Intertek Testing
Services NA in the United States and/or other countries. UL is either a trademark or registered trademark of Underwriters
Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names
may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron
disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or
photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Doc. 7370D
(2053450)
05/15/19
Specifications subject to
change without notice.

Produkt Specifikationer

Mærke: Crestron
Kategori: Ikke kategoriseret
Model: CSAI-PWS40

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CSAI-PWS40 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Crestron Manualer

Crestron

Crestron FT2-700-ELEC-PTL Manual

30 Juli 2025
Crestron

Crestron RMK-AMP-X Manual

30 Juli 2025
Crestron

Crestron DIN-GWDL-SPLTR Manual

30 Juli 2025
Crestron

Crestron HD-CTL-101 Manual

30 Juli 2025
Crestron

Crestron FT2-202-ELEC-PTL Manual

30 Juli 2025
Crestron

Crestron STIRP Manual

30 Juli 2025
Crestron

Crestron CSP-LIR-USB Manual

30 Juli 2025
Crestron

Crestron CEN-IO-COM-202 Manual

30 Juli 2025
Crestron

Crestron CEN-IO-DIGIN-204 Manual

29 Juli 2025
Crestron

Crestron DIN-DLI Manual

29 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock

Hozelock 5102 Manual

2 August 2025
ART

ART 310 Manual

2 August 2025
Gorenje

Gorenje KAS53ZDCINVFT Manual

2 August 2025
Gorenje

Gorenje KAS35ZDCINVFT Manual

2 August 2025
Navman

Navman MY450LMT Manual

2 August 2025
Navman

Navman MiVue 745 Manual

1 August 2025
Hitachi

Hitachi WR22SE Manual

1 August 2025
Synology

Synology M2D20 Manual

1 August 2025
Fluke

Fluke FibertLert-125 Manual

1 August 2025
Buffalo

Buffalo GC882 Manual

1 August 2025