Crestron PAC2M Manual


Læs gratis den danske manual til Crestron PAC2M (32 sider) i kategorien Tynd klient. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Crestron PAC2M, eller vil du spørge andre brugere om produktet?

Side 1/32
Crestron PAC2M
Professional Automation Mini Computer
Operations Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2007 Crestron Electronics, Inc.
Crestron PAC2M Professional Automation Mini Computer
Contents
Professional Automation Mini Computer: PAC2M 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................1
Specifications ..............................................................................................................4
Physical Description....................................................................................................5
Industry Compliance ................................................................................................... 9
Setup ........................................................................................................................................ 10
Network Wiring.........................................................................................................10
Ethernet ..................................................................................................................... 10
Mounting the PAC2M in the Crestron Automation Enclosure.................................. 10
Power Supply ............................................................................................................11
Installation ................................................................................................................. 12
Hardware Hookup .....................................................................................................12
Programming Software............................................................................................................ 14
Earliest Version Software Requirements for the PC ................................................. 14
Programming with D3 Pro.........................................................................................14
Programming with Crestron SystemBuilder.............................................................. 15
Programming with SIMPL Windows ........................................................................ 15
Example Program......................................................................................................15
Uploading and Upgrading........................................................................................................ 16
Establishing Communication.....................................................................................16
Programs and Firmware ............................................................................................17
Program Checks ........................................................................................................ 17
Problem Solving ......................................................................................................................18
Troubleshooting......................................................................................................... 18
Check Network Wiring..............................................................................................21
Reference Documents................................................................................................ 22
Further Inquiries ........................................................................................................ 22
Future Updates ..........................................................................................................22
Software License Agreement...................................................................................................23
Return and Warranty Policies .................................................................................................. 25
Merchandise Returns / Repair Service ......................................................................25
CRESTRON Limited Warranty.................................................................................25
Operations Guide – DOC. 6507A Contents
i
Professional Automation Mini Computer Crestron PAC2M
Professional Automation Mini Control System
The PAC2M is a compact, low-cost alternative to the PAC2 designed for small
lighting and automation applications. At half the size of a PAC2, the PAC2M is
perfect for apartments and smaller homes as well as individual meeting rooms and
lecture halls.
2-Series Engine
Built upon Crestron’s reliable 2-Series control engine, the PAC2M is extensively
programmable using Crestron’s suite of powerful development software and vast
database of drivers and software modules. The PAC2M works seamlessly with
Crestron’s entire line of lighting dimmers and shade controls, keypads and
touchpanels, thermostats, wireless gateways, control cards and expansion modules.
At the heart of the PAC2M is the powerful 32-bit Freescale ColdFire
® processor.
Crestron's exclusive enhanced real-time operating system makes the PAC2M one of
the fastest, most reliable control systems available.
Whole House Integration
The PAC2M provides for the integration of non-Crestron devices and subsystems
through a host of control interfaces. Four isolated relays and four digital input ports
are built in to accommodate motion sensors, contactors, door strikes and other low-
voltage controls. Additional relays, I/O ports, serial COM ports, DTMF interfaces
and shade controllers can be added using Crestron expansion modules at any location
throughout a residence or commercial facility.
Modular Enclosure Installation
The PAC2M is designed to install in a CAEN or CAENIB automation enclosure and
provide a direct bus to a cabinet full of CLX-(or CLXI-)Series lighting control
modules. It is also suitable for surface mount installation without an enclosure where
allowed. Every Crestron lighting system is completely modular and scalable,
allowing virtually unlimited configuration and expansion flexibility.
Cresnet® Distribution
Cresnet is the communications backbone for many Crestron lighting modules, wall
box dimmers, thermostats, keypads and many other devices. This flexible 4-wire bus
streamlines the wiring of a complete Crestron lighting system. The PAC2M provides
connectivity for numerous Cresnet devices on multiple homeruns via eight separate
Cresnet ports. Its built-in Cresnet hub provides two isolated segments, each
supporting 3000 feet of cabling and approximately 25 Cresnet devices. The Cresnet
ports are arranged into two separate power groups providing a clean, flexible 24 Volt
DC power distribution solution. An external power supply is required (sold
separately).
Ethernet and e-Control®2
Built-in 10/100 Ethernet facilitates secure high-speed network connectivity, enabling
extensive capabilities for remote system maintenance and control and providing an
interface to other Crestron control systems. Native features include a built-in email
client to report system troubles and other functions to the homeowner or service
company via instant email notification. An onboard Web server provides the
foundation for Crestron’s exclusive e-Control 2 Xpanel technology, providing secure
IP-based remote control using any Windows
® computer or CD/PocketPC™ PDA
device.
2
Professional Automation Mini Computer: PAC2M Operations Guide – DOC. 6507A
Crestron PAC2M Professional Automation Mini Computer
RoomView® and SNMP
For large facilities utilizing multiple PAC2Ms and other control systems, Crestron’s
exclusive RoomView Help Desk software delivers a comprehensive solution for
remote monitoring and asset management. Also, built-in SNMP support enables
similar capability using third-part network management software, allowing full
control and monitoring from the IT Help Desk or NOC in a format that is familiar to
IT personnel.
Override
An override input is provided to allow an external contact closure to bypass the
PAC2M and activate a preset override state in each connected lighting module.
Memory Expansion
A memory card slot allows for easy expansion of the PAC2Ms internal memory
using any MMC-compatible memory card up to 1 GB. (Memory card not included.)
D3 Pro™ Software
Crestron D3 Pro software eliminates the need for custom programming, providing a
complete design, development and documentation solution for the lighting
professional.
SSL
All Ethernet-enabled 2-Series control systems support SSL (Secure Sockets Layer),
the industry standard for protecting sensitive network communications.
Operations Guide – DOC. 6507A Professional Automation Mini Computer: PAC2M
3
Professional Automation Mini Computer Crestron PAC2M
Specifications
Specifications for the PAC2M are listed in the following table.
PAC2M Specifications
SPECIFICATION DETAILS
Processor
CPU 32-bit Freescale Coldfire Microprocessor
Processing Speed 66 MIPS (Dhrystone 2.1 benchmark)
Memory
SDRAM 32 MB
NVRAM 256 kB
Flash 8 MB
Memory Card* expandable up to 1 GB using MMC
compatible card (not included)
Operating System Real-time preemptive multi-
threaded/multitasking kernel; FAT32 file
system with long names*; supports SIMPL
Windows and SIMPL+
Ethernet 10/100BaseT, auto-negotiating, full/half
duplex, static IP or DHCP/DNS, SSL,
TCP/IP, UDP/IP, CIP, SMTP, SNMP, built-
in Web server and e-mail client; supports
Crestron e-Control2 XPanel and
RoomView applications
Power Requirements 5 Watts (0.21 Amps) @ 24 Volts DC
(PW-2420RU power supply sold separately)
Available Cresnet Power 45 Watts using PW-2420RU (sold
separately)
Environmental
Temperature 41º to 113ºF (5º to 45ºC)
Humidity 10% to 90% RH (non-condensing)
Enclosure Black and gray metal, surface mount box
with (2) integral mounting flanges;
Occupies one module space in a single-
width CAEN or CAENIB enclosure or one
left side module space in a double-width
CAEN or CAENIB enclosure
Dimensions
Height 7.72 in (19.59 cm)
Width 7.05 in (17.89 cm)
Depth 1.71 in (4.33 cm)
Weight 2.14 lbs (0.97 kg)
Available Accessories
CAEN Automation enclosures
CAENIB Automation enclosures
CLX-PWS75 75 Watt Cresnet Power Supply Module
PW-2420RU 50 Watt Power Pack
* Memory cards of less than 512 MB should be formatted using the FAT16 file system. (FAT32 will
not be supported for memory cards of less than 512 MB capacity.)
4
Professional Automation Mini Computer: PAC2M Operations Guide – DOC. 6507A
Crestron PAC2M Professional Automation Mini Computer
Industry Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters
Laboratories Inc.
(E174344)
As of the date of manufacture, the PAC2M has been tested and found to comply with
specifications for CE marking and standards per EMC and Radiocommunications
Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Operations Guide – DOC. 6507A Professional Automation Mini Computer: PAC2M
• 9
Professional Automation Mini Computer Crestron PAC2M
Setup
Network Wiring
When wiring the network, consider the following:
Use Crestron Certified Wire.
Use Crestron power supplies for Crestron equipment.
Provide sufficient power to the system.
CAUTION: Insufficient power can lead to unpredictable results or damage
to the equipment. Please use the Crestron Power Calculator to help calculate
how much power is needed for the system
(http://www.crestron.com/calculators).
For larger networks, use a Cresnet Hub/Repeater (CNXHUB) to maintain
signal quality.
For more details, refer to “Check Network Wiring” on page 21.
Ethernet
The PAC2M also uses high-speed Ethernet for communications between the device
and a control system, computer, digital media server and other IP-based devices.
For information on connecting Ethernet devices in a Crestron system, refer to the
latest version of the Crestron e-Control Reference Guide (Doc. 6052), which is
available for download from the Crestron website.
Mounting the PAC2M in the Crestron Automation
Enclosure
This section covers both CAEN and CAENIB automation enclosures, for simplicity,
hereinafter referred to as CAEN.
CAUTION: The CAEN houses equipment that needs to be air-cooled. Therefore
mount in a well-ventilated area. The ambient temperature range must be 32°F to
104°F (0°C to 40°C). The relative humidity must range from 10% to 90% (non-
condensing). Furthermore, allow adequate clearance in front of the vented cover for
servicing and ventilation.
NOTE: The CAEN is intended for indoor use only.
NOTE: Reliable earth grounding of equipment mounted in a CAEN should be
maintained. Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g., use of power strips).
NOTE: To ensure access to the connectors and memory card slot at the bottom of
the PAC2M, mount the PAC2M so that all CLX-(or CLXI-)Series modules are
above it within the CAEN.
The PAC2M has two flanges that allow the unit to be mounted in a CAEN. Refer to
the latest revision of the CAEN – Automation Enclosures Installation Guide (Doc.
10
• Professional Automation Mini Computer: PAC2M Operations Guide – DOC. 6507A
Professional Automation Mini Computer Crestron PAC2M
built-in Cresnet Hub/Repeater) up to a total of 45 Watts. If additional power is
needed, Crestron recommends its CNPWS-75 (75 watt) External Power Supply.
Installation
Ventilation The PAC2M should be used in a well-ventilated area. The venting holes should not
be obstructed under any circumstances. If the PAC2M is hot to the touch, consider
using forced air ventilation and/or incrementing the spacing between units.
To prevent overheating, do not operate this product in an area that exceeds the
environmental temperature range listed in the table of specifications. Consideration
must be given if installed in a closed or multi-unit rack assembly since the operating
ambient temperature of the rack environment may be greater than the room ambient
temperature. Contact with thermal insulating materials should be avoided on all sides
of the unit.
Bussing Strip Installation The PAC2M is supplied with a brass bussing strip to facilitate commoning (linking)
of multiple terminal block connections. The bussing strip is constructed with four
terminal block positions and may be trimmed to size for various applications or
different devices.
1. To utilize the bussing strip, determine the number of relays to be
commoned for the equipment being installed. If less than four, the strip can
be trimmed to size with a pair of scissors or wire snips.
2. Loosen the terminal block screws and insert the first leg of the bussing strip
into the first common position of the terminal block. The strip engages the
other common positions automatically.
3. Remove approximately 1/8” of the jacket from the common wire and insert
the conductor into one of the terminal block common positions. Tighten the
terminal block screws to lock the wire and bussing strip into place. Insulate
the strip by folding a piece of ¾” wide vinyl electrical tape (such as Scotch
33+) over the spine and as much of the individual legs as possible. Excess
tape at each end of the strip should be pressed closed, then trimmed to
within approximately 1/16” of the end of the strip.
4. When wiring the remaining conductors, remove approximately 1/8” of the
jacket and insert the wires into the proper terminal block positions. To
prevent the possibility of electrical shorts, it is essential that these
conductors do not touch any uninsulated portion of the bussing strip.
5. Securing a tie wrap around the bussing strip is a useful way to provide
strain relief for the wires connected to the terminal block.
Hardware Hookup
Make the necessary connections as called out in the illustration on the next page.
Refer to “Network Wiring” on page 10 before attaching the 4-position terminal block
connector. Apply power after all connections have been made.
When making connections to the PAC2M, be sure to use Crestron power supplies for
Crestron equipment.
12
• Professional Automation Mini Computer: PAC2M Operations Guide – DOC. 6507A
Crestron PAC2M Professional Automation Mini Computer
Hardware Connections for the PAC2M
G/INT/EXT:
24 VDC
TO HUB FROM
INTERNAL OR
EXTERNAL
POWER
POWER:
24 VDC
INPUT,
PARALLELED
WITH 24 VDC
JACK
CRESNET:
TO ANY
CRESNET
NETWORK
DEVICE
LEFT:
TO CLX-(or CLXI-)
SERIES
LIGHTING
CONTROL
MODULE
OVERRIDE:
FROM
EXTERNAL
CONTACT
CLOSURE
RELAY OUTPUT
(1 - 4):
TO
CONTROLLABLE
DEVICES
INPUT (1 - 4):
FROM DEVICE
OUTPUTS
COMPUTER:
TO USB PORT
ON PC
LAN:
10/100 BASE-T
ETHERNET TO
LAN OR WEB
24 VDC
2A MAX:
AC POWER
PACK
(24 VDC, 2A)
MEMORY:
FOR OPTIONAL
MMC
COMPATIBLE
MEMORY
CARD
-CONTACT CLOSURES
-RELAY CLOSURES
Operations Guide – DOC. 6507A Professional Automation Mini Computer: PAC2M
13
Professional Automation Mini Computer Crestron PAC2M
Programming Software
Have a question or comment about Crestron software?
Answers to frequently asked questions (FAQs) can be viewed in the Online Help
section of the Crestron website. To post a question or view questions you have
submitted to Crestron’s True Blue Support, log in at http://support.crestron.com.
First-time users will need to establish a user account.
Earliest Version Software Requirements for the PC
NOTE: Crestron recommends that you use the latest software to take advantage of
the most recently released features. The latest software is available from the Crestron
website.
NOTE: Crestron software and any files on the website are for authorized Crestron
dealers and Crestron Authorized Independent Programmers (CAIP) only. New users
may be required to register to obtain access to certain areas of the site (including the
FTP site).
Crestron has developed an assortment of Windows
-based software tools to develop
a Cresnet system. You can create a program to control the PAC2M control system
using the Crestron programming tools D3 Pro™ or SIMPL Windows. Customers
whose focus is on lighting systems may prefer to use the D3 Pro software since it is
designed especially for creating lighting and environmental system control
applications. Customers already familiar with SIMPL Windows who are including a
lighting system as part of an overall control system project may prefer to continue
using SIMPL Windows. The following are the minimum recommended software
versions for the PC:
Software
TASK REQUIRED SOFTWARE VERSION
Program control system to
operate PAC2M.
SIMPL Windows version 2.07.36 or later
with SIMPL+ Cross Compiler version 1.1 or
later and Library update 404 or later; Also
requires Crestron Database version 18.2.0
or later.
Upload program and firmware. Crestron Toolbox 1.02.38 or later.
Software for lighting and
environmental controls (optional)
Crestron D3 Pro™ version 2.2.12 or later
Program with simple wizards
(optional but recommended).
Crestron SystemBuilder™ version 2.0.6 or
later. Refer to software release notes or
Crestron website for other required
Crestron software packages.
Programming with D3 Pro
Crestron’s D3 Pro lighting software provides all the tools necessary to create a
complete Crestron lighting system for residential applications. The lighting system
includes the control system logic program, touchpanel projects and keypad
programming, documentation and real-time lighting adjustment capabilities.
14
Professional Automation Mini Computer: PAC2M Operations Guide – DOC. 6507A
Crestron PAC2M Professional Automation Mini Computer
Enter the IP address, IP mask and default router of the PAC2M via the
Crestron Toolbox (Functions | Ethernet Addressing); otherwise enable
DHCP.
Confirm Ethernet connections between PAC2M and PC. If connecting
through a hub or router, use CAT5 straight through cables with 8-pin RJ-45
connectors. Alternatively, use a CAT5 crossover cable to connect the two
LAN ports directly without using a hub or router.
Use the Address Book in the Crestron Toolbox to create an entry for the
PAC2M with the PAC2M’s TCP/IP communication parameters.
Display the “System Info” window (click the icon) and select the
PAC2M entry. Communications are confirmed when the device information
is displayed.
Use the Crestron Toolbox to create the PAC2M IP table.
Select Functions | IP Table Setup.
Either add, modify, or delete entries in the IP table. The PAC2M
can have only one IP table entry.
A defined IP table can be saved to a file or sent to the device.
Programs and Firmware
Program or firmware files may be distributed from programmers to installers or from
Crestron to dealers. Firmware upgrades are available from the Crestron website as
new features are developed after product releases. One has the option to upload
programs via the programming software or to upload and upgrade via the Crestron
Toolbox. For details on uploading and upgrading, refer to the SIMPL Windows help
file or the Crestron Toolbox help file.
SIMPL Windows If a SIMPL Windows program is provided, it can be uploaded to the control system
using SIMPL Windows or Crestron Toolbox.
Firmware Check the Crestron website to find the latest firmware. (New users may be required
to register to obtain access to certain areas of the site, including the FTP site.)
Upgrade PAC2M firmware via Crestron Toolbox.
Establish communication with the PAC2M and display the “System Info”
window.
Select Functions | Firmware… to upgrade the PAC2M firmware.
Program Checks
Actions that can be performed on the PAC2M vary depending on whether it is
connected via Cresnet or Ethernet.
Cresnet Connections For Cresnet connections, using Crestron Toolbox, display the network device tree
(Tools | Network Device Tree) to show all network devices connected to the control
system. Right-click on the PAC2M to display actions that can be performed on the
PAC2M.
Ethernet Connections For Ethernet connections, display the “System Info window (click the icon) and
select the Functions menu to display actions that can be performed on the PAC2M.
Operations Guide – DOC. 6507A Professional Automation Mini Computer: PAC2M
17


Produkt Specifikationer

Mærke: Crestron
Kategori: Tynd klient
Model: PAC2M

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron PAC2M stil et spørgsmål nedenfor, og andre brugere vil svare dig




Tynd klient Crestron Manualer

Crestron

Crestron CP3 Manual

20 August 2024
Crestron

Crestron PAC2M Manual

19 August 2024

Tynd klient Manualer

Nyeste Tynd klient Manualer

ELO

ELO ECMG2C Manual

28 December 2024
ELO

ELO ECMG2B Manual

28 December 2024
ELO

ELO E992401 Manual

28 December 2024
ELO

ELO ECM2 Manual

28 December 2024
ELO

ELO E991018 Manual

28 December 2024
ELO

ELO ECMG2 Manual

27 December 2024
ELO

ELO E991367 Manual

27 December 2024
ELO

ELO E000739 Manual

27 December 2024