Crestron SAROS SR6T-W-T-EACH Manual

Crestron Vugge/dockingstation SAROS SR6T-W-T-EACH

Læs gratis den danske manual til Crestron SAROS SR6T-W-T-EACH (2 sider) i kategorien Vugge/dockingstation. Denne vejledning er vurderet som hjælpsom af 63 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 32 anmeldelser. Har du et spørgsmål om Crestron SAROS SR6T-W-T-EACH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Saros

2-Way Surface Mount Speakers

quickstart guide

SAROS_SR4T/SAROS_SR6T/SAROS_SR8T

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

SAROS_SR4T/SR6T/SR8T

4. Carefully mount the speaker onto the QuickBall mounting bracket, ensuring

that the ball is fully inserted into the cavity. Rotate and set the speaker at the

desired angle, and raise the ball socket clamp lever into position against the

bottom of the speaker to secure the speaker in position. Use the supplied

security screw to prevent the lever from being accidentally pulled, which

releases the speaker.

5. Attach a security cable (SPKA-ST-15, sold separately) to the security cable

attachment point. The other end of the cable must be attached to a secondary

point able to support several times the weight of the speaker.

6. The Saros speakers are equipped with a 70 V/100 V matching transformer for

distributed audio systems. The transformer tap selector switch on the rear

panel is used for setting the speaker power level. Use a flat blade screwdriver

to adjust the switch.

a. For SAROS_SR4T 70 V distributed systems, use the left side settings and

select from 1.88, 3.75, 7.5, 15, or 30 watts.

b. For SAROS_SR4T 100 V distributed systems, use the right side settings

and select from 3.75, 7.5, 15, or 30 watts. The X position should not be

used.

c. For SAROS_SR6T and SAROS_SR8T 70 V distributed systems, use the

left side settings and select from 3.75, 7.5, 15, 30, or 60 watts.

d. For SAROS_SR6T and SAROS_SR8T 100 V distributed systems, use the

right side settings and select from 7.5, 15, 30, or 60 watts. The X position

should not be used.

The switch may also be set to 8Ω operation, bypassing the transformer

completely. This setting should be used only for 8 ohm audio systems.

NOTE: Before starting installation, ensure the wall and wall material are capable of supporting the combined

weight of the speakers and the wall mount assemblies. Refer to section



for speaker weights.

QUICKSTART DOC. 7149E (2033424) 08.14

Installation

Saros

speakers by Crestron

deliver professional grade performance and

flexible installation in a range of popular sizes for demanding commercial

applications. Solid construction and high-end components are hallmarks of the

complete Saros speaker line. Each Saros model is engineered to achieve a

smooth, even coverage pattern, and clear, natural sound quality through the

employment of a horn-loaded titanium dome tweeter, a high-performance

damped cone woofer, and a finely tuned crossover.

Featuring a unique “QuickBall” mounting system, the Saros speakers can be

mounted to any solid, flat surface with the ability to orient and aim the speaker

in virtually any position. The QuickBall bracket achieves a very clean and

stable installation using a tool-free ball-and-socket mechanism. Simply

position the speaker as desired and flip the clamp lever closed. A security

screw is included to deter theft by preventing the lever from being released.

Saros speakers, supplied in pairs, are available in black or white and can be

painted to blend with the surrounding architecture.

Physical Views (SAROS_SR8T Shown)

Front View

(Grille Removed)

10.73 in

(273 mm

)

2.16 in

(55 mm)

Side View

Rear View

(Mounting Bracket

Removed)

6.89 in

(175 mm)

9.05 in

(230 mm)

Bottom View

9.57 in

(244 mm)

13.31 in

(338 mm)

Security

Cable

Attachment

Point

Security

Screw

Speaker

Cable

Access

Hole

Ball Socket

Clamp Lever

Detachable

Screw Terminal Block

Quick Ball

Mounting

Bracket

From

Audio

Source

Parallel

Speaker

+ + - -

THRU

SAROS_SR4T

Transformer Tap

Selection Switch

Label

SAROS_SR6T,

SAROS_SR8T

Transformer Tap

Selection Switch

SAROS_SR4T/SR6T/SR8T

Refer to the illustration to the right as necessary, and install the speakers as follows:

1. Route the cables from the audio source to the intended speaker locations while

following all appropriate local codes.

2. Attach the QuickBall mounting bracket directly to the wall or to a flush mounted

1-gang US, UK, or European electrical box, allowing the cable coming through

the wall (and the electrical box, if used) to exit through the speaker cable

access hole of the mounting bracket.

NOTE: If the mounting bracket is to be attached to an electrical box, be sure

it is also attached to surrounding framing to provide the support needed to

hold the weight of the speaker.

The QuickBall mounting bracket can also be mounted to a light pole or post

using pole mounting straps (not included).

3. Detach the 4-pin screw terminal block connector from the speaker. Connect the

audio source’s + and - outputs to the connector’s outer + and - (IN) terminals.

Maximum wire size is 12 AWG. Use the inner + and - (THRU) terminals to

connect a second speaker in parallel.

NOTE: The number of speakers that can be added is limited only by the

specifications of the amplifier.

a. Route the audio source’s (and a second speaker’s) wiring through the

supplied weather boot (if used). Strip the wires 1/4 in (~6 mm), twist the

strands, insert them into the terminal block, and tighten the screws to

secure them.

b. Reattach the terminal block to the speaker connector.

quickstart guide

SAROS_SR4T/SAROS_SR6T/SAROS_SR8T

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

Saros

2-Way Surface Mount Speakers

SAROS_SR4T/SR6T/SR8T

QUICKSTART DOC. 7149E (2033424) 08.14

The specific patents that cover Crestron products are listed at patents.crestron.com.

Crestron, the Crestron logo, and Saros are either trademarks or registered trademarks of Crestron Electronics, Inc. in the

United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this

document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary

interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

Specifications

SPECIFICATION SAROS_SR4T

Drivers

Woofer

Tweeter

Crossover Frequency

Impedance

Transformer Taps

Frequency Response

Frequency Range

Power Handling

Sensitivity

Environmental

Temperature

Humidity

Splash Resistance

SAROS_SR4T, SAROS_SR6T, SAROS_SR8T Specifications

4 in (102 mm) polypropylene with ring

mode decoupled cloth surround and steel

basket

0.79 in (20 mm) horn-loaded titanium dome

2.5 kHz

8 ohms nominal with transformer set to

8Ω

1.88, 3.75, 7.5, 15, 30 watts at 70 V;

3.75, 7.5, 15, 30 watts at 100 V

100 Hz to 16 kHz (±3 dB)

80 Hz to 18 kHz (-10 dB)

100 watts program (8 ohms)

-2º to 120º F (-19º to 49º C)

5% to 95% RH (non-condensing)

IPx4 rated per IEC 60529

8 in (203 mm) polypropylene with ring

mode decoupled cloth surround and steel

basket

0.98 in (25 mm) horn-loaded titanium dome

2 kHz

8 ohms nominal with transformer set to

8Ω

3.75, 7.5, 15, 30, 60 watts at 70 V;

7.5, 15, 30, 60 watts at 100 V

80 Hz to 16 kHz (±3 dB)

60 Hz to 18 kHz (-10 dB)

200 watts program (8 ohms)

-2º to 120º F (-19º to 49º C)

5% to 95% RH (non-condensing)

IPx4 rated per IEC 60529

SAROS_SR6T

6.5 in (153 mm) polypropylene with ring

mode decoupled cloth surround and steel

basket

0.98 in (25 mm) horn-loaded titanium dome

2 kHz

8 ohms nominal with transformer set to

8Ω

3.75, 7.5, 15, 30, 60 watts at 70 V;

7.5, 15, 30, 60 watts at 100 V

90 Hz to 16 kHz (±3 dB)

70 Hz to 18 kHz (-10 dB)

-2º to 120º F (-19º to 49º C)

5% to 95% RH (non-condensing)

IPx4 rated per IEC 60529

150 watts program (8 ohms)

SAROS_SR8T

89.5 dB @ 1 W/1 m 90 dB @ 1 W/1 m 91.5 dB @ 1 W/1 m

The following table provides corrective action for possible trouble situations. If further

assistance is required, please contact a Crestron customer service representative.

Further Inquiries

To locate specific information or resolve questions after reviewing this guide, contact

Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for assistance

within a particular geographic region, refer to the listing of Crestron worldwide offices at

www.crestron.com/offices.

To post a question about Crestron products, log onto Crestron’s Online Help at www.cre-

stron.com/onlinehelp. First-time users must establish a user account to fully benefit from

all available features.

Future Updates

As Crestron improves functions, adds new features, and extends the capabilities of the

SAROS_

SR4T,

SAROS_

SR6T, and

SAROS_

SR8T speakers

, additional information may

be made available as manual updates. These updates are solely electronic and serve as

intermediary supplements prior to the release of a complete technical documentation

revision.

Check the Crestron website periodically for manual update availability and its relevance.

Updates are identified as an “Addendum” in the Download column.

Problem Solving

Troubleshooting

TROUBLE POSSIBLE CAUSE(S)

CORRECTIVE ACTION

There is either no

sound or the sound

from the speakers is

intermittent.

There is a cable connection

error.

Verify the cable connections

between the amplifier and speakers.

The amplifier is not

receiving an input signal

or there is an amplifier

malfunction.

Verify that the amplifer is functioning

correctly, that it is receiving an input

signal, and that the correct input

source is selected.

There is a faulty device in

the system.

Verify that all devices in the system

are functioning properly.

Constant noise such as

buzzing, humming, or

hissing comes from the

speakers.

There is a system

grounding fault.

Verify the system grounding

connection.

The low frequency

output is poor.

Verify speaker connection

polarity (i.e., + on speaker to

+ on amplifier).

Verify speaker connection polarity

(i.e., + on amplifier to + on speaker).

Construction

Enclosure

Grille

Mounting

Dimensions

Height

Width

Depth

Positioning

Yaw (Horizontal)

Pitch (Vertical)

Roll

ABS plastic, textured finish, paintable

Aluminum, powder coated, paintable

Surface mount to a solid flat surface with

option to position over a flush-mounted

1-gang electrical box, 1-gang UK (BS

4662) electrical box, or 1-gang European

(DIN 49073) electrical box;

Pole mount (straps not included);

Rigging point for safety tether

(SPKA-ST-15 sold separately);

Theft-resistant security screw

8.67 in (220 mm)

5.91 in (151 mm)

6.50 in (165 mm), 8.66 in (220 mm)

with mounting bracket

± 30°

360°

ABS plastic, textured finish, paintable

Aluminum, powder coated, paintable

Surface mount to a solid flat surface with

option to position over a flush-mounted

1-gang electrical box, 1-gang UK (BS

4662) electrical box, or 1-gang European

(DIN 49073) electrical box;

Pole mount (straps not included);

Rigging point for safety tether

(SPKA-ST-15 sold separately);

Theft-resistant security screw

13.31 in (338 mm)

9.57 in (244 mm)

± 30°

360°

ABS plastic, textured finish, paintable

Aluminum, powder coated, paintable

Surface mount to a solid flat surface with

option to position over a flush-mounted

1-gang electrical box, 1-gang UK (BS

4662) electrical box, or 1-gang European

(DIN 49073) electrical box;

Pole mount (straps not included);

Rigging point for safety tether

(SPKA-ST-15 sold separately);

Theft-resistant security screw

11.19 in (285 mm)

8.08 in (205 mm)

6.70 in (170 mm), 8.86 in (225 mm)

with mounting bracket

± 30°

360°

Weight

5.9 lb (~3 kg) 10.1 lb (~5 kg)8.3 lb (~4 kg)

6.89 in (175 mm), 9.05 in (230 mm)

with mounting bracket

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Vugge/dockingstation
Model:	SAROS SR6T-W-T-EACH
Kode for international beskyttelse (IP):	IPX4
Bredde:	205 mm
Dybde:	170 mm
Højde:	285 mm
Vægt:	3800 g
Antal pr. pakke:	1 stk
Produktfarve:	Hvid
Produkttype:	2.1 bærbart højttalersystem
Wi-Fi:	Ingen
Bluetooth:	Ingen
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Antal højttalere:	1
Udgangseffekt (RMS):	150 W
Husmateriale:	Acrylonitrilbutadienstyren
Anbefalet brug:	Universel
Frekvensområde:	70 - 18000 Hz
Impedens:	8 ohm (Ω)
Forbindelsesteknologi:	Ledningsført
Højttaler, type:	2-vejs
Lyd-output kanaler:	2.1 kanaler
Strømkilde type:	Andet
Diskanthøjttaler:	Ja
Sensitivitet:	90 dB
Diskant diameter:	25 mm
Bashøjttaler:	Ja
Woofer diameter:	165 mm
Driftstemperatur (køling) (T-T):	-19 - 49 °C