Crestron ST-RMK Manual

Crestron Ikke kategoriseret ST-RMK

Læs gratis den danske manual til Crestron ST-RMK (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Crestron ST-RMK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Rack Mount Kit: ST-RMK

Physical Description

The ST-RMK is a rack mount kit that is capable of holding either one or two CEN Ethernet Modules,

SmarTouch STS Expansion Modules, ST-CP Control Processors, or any combination of units in a

single rack space. The front extrusion and bracket are provided to occupy the open bay of the ST-RMK

so that when only one module (or ST-CP) is installed, no gaps are visible in the rack. The front

extrusion and bracket may be installed in either the left or right bay of the ST-RMK. When the

ST-RMK accommodates two modules, the extrusion and bracket are not used.

Items 1 through 6 listed below are the supplied components of the ST-RMK. The tools required for

installation of the ST-RMK are a #1 Phillips 1/4-inch hex bit, a 1/4-inch hex socket, and an inch-pound

torque driver. Follow the installation procedures in the next section.

Supplied Components

ITEM DESCRIPTION PART NUMBER QUANTITY

1 Assembly, chassis & front extrusion AY17489-1 1

2 Assembly, front extrusion & label AY17490-1 1*

3 Bracket MTBK02315-1 1*

4 Screw, 4-40 x 1/4"L, steel, pan, phillips, black SR04-40-0R2500-8 8*

5 Nut, 4-40, hex, steel, zinc MTPL02390-1 4

6 Washer, lock, steel, internal, #4, zinc WA04L0-1 4

* Depending upon number of modules installed, not all items may be required.

Rack Mount Instructions

Front Extrusion and Bracket Installation

If two modules (or ST-CPs) are to be installed onto the ST-RMK, skip this procedure and proceed to

the next section. If only one module is to be installed, the front extrusion and bracket should be

installed into either the left or right bay of the chassis. To install the extrusion and bracket, refer to the

diagrams and steps below (installation into the right bay is shown, left bay installation is identical).

Install Front Extrusion & Bracket

65 4

DIAGRAM FOR STEPS 1 & 2 DIAGRAM FOR STEPS 3 - 6

X 4 X 2

Installation Guide - DOC. 5664A Rack Mount Kit: ST-RMK •

•

•• 1

1. With the label on the front extrusion properly orientated, position the four threaded

studs of the extrusion through the four holes of the bracket .

2. Loosely install four lockwashers and four hex nuts onto the studs of the front

extrusion. Using a 1/4-inch hex socket and an inch-pound torque driver, tighten the hex

nuts to 8-inch pounds (0.90 newton-meters) to secure extrusion.

3. Place the chassis upside down on a clean surface.

4. Turn front extrusion and bracket upside-down and position into open bay of chassis.

5. Align two screw holes in bracket with holes in the chassis. Using a #1 Phillips 1/4-

inch hex bit and an inch-pound torque driver, install two screws and tighten to 8-inch

pounds (0.90 newton-meters) to secure bracket.

6. Return the ST-RMK to its proper orientation and proceed to the next procedure to install

a module (or ST-CP) into the ST-RMK.

Module (or ST-CP) Installation into ST-RMK

Refer to the procedure below and complete the following steps for proper installation of a module (or

ST-CP) into the ST-RMK.

1. Place module into chassis so that front panel of the module is exposed, the two front

rubber feet of the module fit into cutouts in the chassis, and the two rear rubber feet

extend from the rear edge.

2. As shown below, keep the module and chassis together and place upside down on a

clean surface.

Module Installation

(EXAMPLE MODULE)

x 4

3. Align screw holes in the chassis with holes in the module. Using a #1 Phillips 1/4-inch

hex bit and an inch-pound torque driver, install four screws and tighten to 4-inch

pounds (0.45 newton-meters) to secure module.

4. If installing another module, repeat this procedure. If not installing another module,

return ST-RMK and module(s) to proper orientation and install into system rack. (Rack

mounting screws are not supplied.)

2 •

•

•• Rack Mount Kit: ST-RMK Installation Guide - DOC. 5664A

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	ST-RMK

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron ST-RMK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crestron Manualer

Crestron FT2-700-ELEC-PTL Manual

30 Juli 2025

Crestron RMK-AMP-X Manual

30 Juli 2025

Crestron DIN-GWDL-SPLTR Manual

30 Juli 2025

Crestron HD-CTL-101 Manual

30 Juli 2025

Crestron FT2-202-ELEC-PTL Manual

30 Juli 2025

Crestron STIRP Manual

30 Juli 2025

Crestron CSP-LIR-USB Manual

30 Juli 2025

Crestron CEN-IO-COM-202 Manual

30 Juli 2025

Crestron CEN-IO-DIGIN-204 Manual

29 Juli 2025

Crestron DIN-DLI Manual

29 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MY500XT Manual

1 August 2025

Navman FOCUS150 GPS Manual

1 August 2025

Scheppach TW1000 Manual

1 August 2025

Navman MiVue 750 WIFI Manual

1 August 2025

Navman MiVue Drive FHD Manual

1 August 2025

Midea MEC64 Manual

1 August 2025

Navman MY50T Manual

1 August 2025

Navman M100 Manual

1 August 2025

Navman MiVue 770 SAFETY Manual

1 August 2025

Navman MiVue 790 Manual

1 August 2025