Crestron TST-902-DS Manual

Crestron Batterioplader TST-902-DS

Læs gratis den danske manual til Crestron TST-902-DS (2 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Crestron TST-902-DS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

TST-902-BTP/TST-902-DS

Accessories for the TST-902

Installation Guide

Introduction

This document provides installation and connection instructions for the TST-902-BTP

Battery Pack and TST-902-DS Docking Station that ship with the Crestron

TST-902

Wireless Touch Screen.

Install the New Battery Pack

Perform the following procedure to install the new TST-902-BTP in a TST-902 touch

screen.

1. Orient the battery pack so the “Lift to Remove” tag is visible and the multipin

connector is on the left.

2 Make sure the pin side of the multipin connector on the touch screen is facing

upward and connect it to the battery pack.

3. Gently place the battery pack in the battery compartment of the touch screen.

4. Reattach the battery compartment cover to the device by placing it on the back of

the touch screen, below the cover markings, and then sliding it up into place.

Charge the Battery Pack

To charge the TST-902-BTP, mount the touch screen on a powered TST-902-DS docking

station.

NOTE: The battery pack may take up to 6 hours to charge in a powered touch screen if

the panel is in use while charging.

Store the Battery Pack

The TST-902-BTP can be stored in a temperate, dry place (removed from the touch screen

and docking station) for up to 3 months without signicant irreversible degradation of

performance. The self-discharge rate is a function of temperature and internal resistance.

Storage at high temperature reduces charge retention. Best results occur if the

TST-902-BTP is stored at a temperature between 32˚ and 95˚F (0˚ and 35˚C).

NOTE: Lithium-ion batteries must be stored at 50% charge and cycled every 3 months.

Dispose of the Battery Pack

NOTE: The TST-902-BTP contains a lithium-ion battery. When the unit can no longer

retain a charge, it must be recycled or disposed of properly. Follow local ordinances and

regulations for disposal.

TST-902-BTP

Remove the Old Battery Pack

NOTE: The TST-902 Wireless Touch Screen contains electrostatic discharge (ESD)

sensitive devices. To avoid damaging the unit, perform the following procedure while

wearing a grounding strap that is properly grounded or while working on a grounded

workstation.

NOTE: To prevent damage to the multipin connector and wiring, use care when

handling the TST-902-BTP.

Perform the following procedure to remove the existing TST-902-BTP from a TST-902

touch screen.

1. Insert the included pin tool into one of the tab release holes on the back of the unit

and then slide the bottom cover downward to release the tab on that side.

Release the Tabs on the Battery Compartment Cover

Additional Resources

Visit the product pages on the Crestron website

(www.crestron.com) or scan the QR codes for

additional information and the latest rmware

updates.

2. Insert the pin tool into the other tab release hole and then slide the bottom cover

downward to release the tab on that side.

3. Slide the bottom cover downward about 3/4” (19 mm) to expose the cover markings

and then lift the cover to remove it.

Slide the Cover to Reveal the Cover Markings

4. Gently tug the “Lift to Remove” tag on the battery pack to unseat it from the touch

screen.

5. Separate the multipin connector in the battery compartment from the battery pack.

Lift the Battery and Separate It from the Multipin Connector

NOTE: The battery must be recycled. Deliver the battery pack to an

appropriate recycling facility.

Tab Release Holes

Cover Markings

Multipin Connector

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Batterioplader
Model:	TST-902-DS
Type:	Indendørs batterioplader
Bredde:	170 mm
Dybde:	129 mm
Højde:	131 mm
Vægt:	1049 g
Produktfarve:	Sort
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Driftstemperatur (T-T):	0 - 45 °C
Strømkilde type:	Vekselstrøm
Udgangsspænding:	24 V
Udgangsstrøm:	0.75 A
Antal understøttede batterier:	1
Indgangsspænding:	100-240 V
Kompatible produkter:	Crestron TST-902
Indgangsfrekvens:	50/60 Hz