Crestron ZUMMESH-JBOX-DALI Manual

Crestron Ikke kategoriseret ZUMMESH-JBOX-DALI

Læs gratis den danske manual til Crestron ZUMMESH-JBOX-DALI (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Crestron ZUMMESH-JBOX-DALI, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The Zūm™ Wireless ZUMMESH-JBOX-DALI is a single-

channel DALI controller capable of controlling up to 64

DALI compatible drivers. The ZUMMESH-JBOX-DALI

communicates with other Zūm devices such as keypads,

occupancy sensors, vacancy sensors, and daylight sensors.

NOTE: The ZUMMESH-NETBRIDGE (sold separately)

is required to create and control DALI groups. The

ZUMMESH-NETBRIDGE must be connected to the

ZUMMESH-JBOX-DALI for DALI group control.

Check the Box

Item Qty

ZUMMESH-JBOX-DALI 1

Nut, Wire Twist, Yellow, 22-10 AWG

(P/N 2049245)

Nut, Lock, 1/2 in. - 14, Conduit, Steel

(P/N 2047626)

Installation

WARNING: To avoid fire, shock, or death, turn off the power

at the circuit breaker or fuse and test that the power is off

before wiring!

NOTE: Observe the following points:

• Install and use this product in accordance with

appropriate electrical codes and regulations.

• A licensed electrician should install this product.

• The product projects 3-11/16 in. (93 mm) from the

junction box when installed.

To install a ZUMMESH-JBOX-DALI:

1. Turn the power off at the circuit breaker.

2. Mount the ZUMMESH-JBOX-DALI to the J-box using

a locknut.

3. Wire the ZUMMESH-JBOX-DALI as shown.

To DALI

controlled loads

DALI Input/Output

(purple)

DALI Input/Output

(gray)

Neutral

(white)

Hot

(black)

100-277 VAC

power from

breaker

To install a ZUMMESH-NETBRIDGE:

NOTE: For product specifications and additional installation

details, refer to the ZUMMESH-NETBRIDGE Installation

Guide (Doc. 7955) at for

www.crestron.com/manuals

details.

1. Use a flat-head screwdriver to remove the cover on

the ZUMMESH-JBOX-DALI. Insert the flat-head

screwdriver into the slot next to the cover and pry up

to remove the cover.

2. Align the ports on the ZUMMESH-NETBRIDGE

and the ZUMMESH-JBOX-DALI, and then

insert the ZUMMESH-NETBRIDGE into the

ZUMMESH-JBOX-DALI. The J-box module snaps into

place.

Operation

Prior to room commissioning, the ZUMMESH-JBOX-DALI

uses DALI broadcast to control all connected

lights simultaneously. After commissioning the

ZUMMESH-JBOX-DALI, addressing devices and creating

groups, the ZUMMESH-JBOX-DALI will control drivers

assigned to the groups.

NOTES: Connect the ZUMMESH-NETBRIDGE (sold

separately) directly to the ZUMMESH-JBOX-DALI to create

and control DALI groups. The ZUMMESH-JBOX-DALI

functions in broadcast mode if the ZUMMESH-NETBRIDGE

is not connected.

Test the Ballasts

To verify that all drivers have been properly wired, press

the TEST button to toggle the drivers that are assigned to

groups.

To test the dimming function of the drivers, press and hold

the TEST button.

NOTE: if the ZUMMESH-JBOX-DALI is not commissioned,

the device operates in DALI broadcast mode and

controls all of the connected drivers simultaneously.

After the ZUMMESH-JBOX-DALI is commissioned, the

ZUMMESH-JBOX-DALI only toggles or dims drivers that

are assigned to groups.

Commissioning

Use the Crestron Zūm app to commission the

ZUMMESH-JBOX-DALI.

For details on commissioning, refer to the Zūm Light

Control System Product manual (Doc. 7957)

at .

www.crestron.com/manuals

ZUMMESH-JBOX-DALI

Zūm™ Wireless DALI® Controller

Factory Reset

Perform a factory reset when the ZUMMESH-JBOX-DALI is

removed from the network or to remove the configuration

settings from the device. The ZUMMESH-JBOX-DALI must

also be factory reset if it is being moved to a different

system.

NOTE: New-in-box devices do not need to be factory reset

before joining a system.

To factory reset the ZUMMESH-JBOX-DALI, press and hold

the buttons until the SETUP and TEST SETUP LED lights

(about 10 seconds), and then release both buttons. The

SETUP LED and the connected load output turn on.

T EST

SET UP

TEST

SETUP

Press and hold and SETUP

TEST until the LED flashes

Additional Information

Scan or click the QR code for detailed product information.

ZUMMESH-JBOX-DALI

Compliance and Legal

Original Instructions: The U.S. English version of this document is the original

instructions. All other languages are a translation of the original instructions.

Regulatory Model: M201904001

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the

following conditions: (1) This device may not cause harmful interference and (2)

this device must accept any interference received, including interference that

may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the

manufacturer responsible for compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

This product is Listed to applicable UL® Standards and requirements tested by

Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par

Underwriters Laboratories Inc.

This product conforms to ANSI/UL STD 2043 tested by Intertek® services.

The product meets the requirements of UL 2043 for installation in an

environmental air-handling (plenum) space, such as above a suspended ceiling.

The product is tested by an NRTL (Nationally Recognized Testing Laboratory)

and complies with ANSI/UL2043 (Fire Test for Products Installed in Air-

Handling Spaces). Full compliance requires plenum rated cables.

The product warranty can be found at .

www.crestron.com/warranty

The specific patents that cover Crestron products are listed at

www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific

information, please

visit www.crestron.com/opensource.

Crestron, the Crestron logo, and Zūm are either trademarks or registered

trademarks of Crestron Electronics, Inc. in the United States and/or other

countries. UL and the UL logo are either trademarks or registered trademarks

of Underwriters Laboratories, Inc. in the United States and/or other countries.

Intertek is either a trademark or registered trademark of Intertek Group in the

United States and/or other countries. The ETL logo is either a trademark or

registered trademark of Intertek Testing Services NA in the United States and/

or other countries. DALI is either a trademark or registered trademark of ZVEI

- Zentralverband Elektrotechnik- und Elektronikindustrie in the United States

and/or other countries. Other trademarks, registered trademarks, and trade

names may be used in this document to refer to either the entities claiming the

marks and names or their products. Crestron disclaims any proprietary interest

in the marks and names of others. Crestron is not responsible for errors in

typography or photography.

Crestron Electronics, Inc.

15 Volvo Drive, Rockleigh, NJ 07647

Tel: 888.CRESTRON

Fax: 201.767.7576

www.crestron.com

Quick Start - Doc. 8448A

(2053429)

11/06/19

Specifications subject to

change without notice.

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	ZUMMESH-JBOX-DALI

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron ZUMMESH-JBOX-DALI stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crestron Manualer

Crestron FT2-700-ELEC-PTL Manual

30 Juli 2025

Crestron RMK-AMP-X Manual

30 Juli 2025

Crestron DIN-GWDL-SPLTR Manual

30 Juli 2025

Crestron HD-CTL-101 Manual

30 Juli 2025

Crestron FT2-202-ELEC-PTL Manual

30 Juli 2025

Crestron STIRP Manual

30 Juli 2025

Crestron CSP-LIR-USB Manual

30 Juli 2025

Crestron CEN-IO-COM-202 Manual

30 Juli 2025

Crestron CEN-IO-DIGIN-204 Manual

29 Juli 2025

Crestron DIN-DLI Manual

29 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025