CyberData Systems SIP-enabled VoIP V3 Manual

CyberData Systems Intercomsystem SIP-enabled VoIP V3

Læs gratis den danske manual til CyberData Systems SIP-enabled VoIP V3 (4 sider) i kategorien Intercomsystem. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 16 anmeldelser. Har du et spørgsmål om CyberData Systems SIP-enabled VoIP V3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Quick Start Guide 930503A

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/products/voip/digitalanalog/intercomemergency/docs.html

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 13W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

VoIP Emergency Intercom

Quick Start Guide

The IP Endpoint Company

Quick Start Guide 930503A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity above the

ethernet port on the back of the Intercom. See the following figure:

3.2. The GREEN Link LED blinks off once during the boot up process and then

comes on again and remains constant (solid GREEN). The YELLOW

Activity LED may be blinking depending on the network activity.

During the initialization process, the GREEN Call Button LED should come

on and be constant (solid GREEN). After the Intercom has completed

booting, the LED will blink twice and then remain constant thereafter.

Normally, this process will take about 30 seconds. However, if no DHCP1 is

available, then this process could take up to 2 minutes.

3.3. When the Intercom has completed the initialization process, press and hold

the RTFM switch (SW1 button) for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

1. This only applies to firmware versions 6.x.x and later. For versions 5.1.2 and

earlier, the default static IP address is 10.10.10.10.

Link LED

Activity LED

Produkt Specifikationer

Mærke:	CyberData Systems
Kategori:	Intercomsystem
Model:	SIP-enabled VoIP V3

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberData Systems SIP-enabled VoIP V3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Intercomsystem CyberData Systems Manualer

CyberData Systems 011491 Manual

31 August 2024

CyberData Systems SIP Talk-Back Manual

31 August 2024

CyberData Systems SIP-enabled VoIP V3 Manual

31 August 2024

CyberData Systems V3 SIP-enabled IP Manual

31 August 2024

CyberData Systems SIP-enabled IP V3 Manual

31 August 2024

Intercomsystem Manualer

Nyeste Intercomsystem Manualer

Hanwha SBS-165B Manual

30 Januar 2025

Philips WelcomeEye Wireless Manual

14 Januar 2025

Dahua Technology DHI-VTH5221DW-S Manual

11 Januar 2025

Pentatech VT35 Manual

3 Januar 2025

Somfy V500 Manual

30 December 2025

Akuvox MD06 Manual

29 December 2024

Elcom REN410X Manual

28 December 2024

Toucan TVDP05GR Manual

17 December 2024

Vimar ELVOX 80N1 Manual

15 December 2024

Vimar ELVOX 8001 Manual

15 December 2024