CyberData Systems V3 SIP-enabled IP Manual

CyberData Systems Intercomsystem V3 SIP-enabled IP

Læs gratis den danske manual til CyberData Systems V3 SIP-enabled IP (4 sider) i kategorien Intercomsystem. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12 anmeldelser. Har du et spørgsmål om CyberData Systems V3 SIP-enabled IP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Quick Start Guide 930473A

1.0 Out-of-Box and Prior to Final Installation

1.1. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/products/voip/digitalanalog/intercomv3/docs.html

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 13W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

VoIP V3 Outdoor Intercom

Quick Start Guide

The IP Endpoint Company

Quick Start Guide 930473A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity above the

ethernet port on the back of the Intercom. See the following figure:

3.2. The GREEN Link LED blinks off once during the boot up process and then

comes on again and remains constant (solid GREEN). The YELLOW

Activity LED may be blinking depending on the network activity.

During the initialization process, the GREEN Call Button LED should come

on and be constant (solid GREEN). After the Intercom has completed

booting, the LED will blink twice and then remain constant thereafter.

Normally, this process will take about 30 seconds. However, if no DHCP1 is

available, then this process could take up to 2 minutes.

3.3. When the Intercom has completed the initialization process, press and hold

the RTFM switch (SW1 button) for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

1. This only applies to firmware versions 6.x.x and later. For versions 5.1.2 and

earlier, the default static IP address is 10.10.10.10.

Link LED

Activity LED

Produkt Specifikationer

Mærke:	CyberData Systems
Kategori:	Intercomsystem
Model:	V3 SIP-enabled IP

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberData Systems V3 SIP-enabled IP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Intercomsystem CyberData Systems Manualer

CyberData Systems 011491 Manual

31 August 2024

CyberData Systems SIP Talk-Back Manual

31 August 2024

CyberData Systems SIP-enabled VoIP V3 Manual

31 August 2024

CyberData Systems V3 SIP-enabled IP Manual

31 August 2024

CyberData Systems SIP-enabled IP V3 Manual

31 August 2024

Intercomsystem Manualer

Nyeste Intercomsystem Manualer

Viking E-40-SS-EWP Manual

28 Marts 2025

Viking E-1600-40-IPEWP Manual

27 Marts 2025

Hikvision DS-KH2230T Manual

27 Marts 2025

Viking E-1600-20A-EWP Manual

27 Marts 2025

Louroe Electronics AOP-SP-PB Manual

10 Marts 2025

2N Telecommunications 9151104 Manual

20 Februar 2025

2N Telecommunications Indoor Compact Manual

20 Februar 2025

Axis TI8202 Manual

20 Februar 2025

Axis TI8904 Manual

20 Februar 2025

Rollei Xtalk Manual

5 Februar 2025