Danfoss TP5E Manual

Danfoss Termostat TP5E

Læs gratis den danske manual til Danfoss TP5E (4 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Danfoss TP5E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

TP5E

Electronic Programmable Room Thermostat

USER INSTRUCTIONS

Fig. 1

Fig. 3

Fig. 2

Fig. 5

Fig. 6

Fig. 4

The following table shows the factory pre-set programme,

which may be re-instated at any time by performing a

RESET.

Days 1 to 5 (Weekdays) Days 6 & 7 (Weekend)

Setting Time Temp. Setting Time Temp.

1 6:30 20 1 7:00 20

2 8:30 15 2 16:00 21

3 11:30 20 3 23:00 15

4 13:30 15 4 0:00 15

5 16:30 21 5 1:00 15

6 22:30 15 6 1:59 15

The factory pre-set programme for days 6 & 7 (Saturday

and Sunday) provides full heating throughout the day

until 23:00, after which the 15°C may be raised manually

to the level required using the sbutton. The manual

over-ride will last for up to one hour until midnight (0:00)

after which it can be used up to twice again to provide full

heating until 1:59 if required.

CHANGING THE SETTINGS

While reviewing the settings the switching time and

control temperature may be changed using the + and -

(time) and s and t (temperature) buttons.

When changing the switching times it is not possible to

set the times out of sequence.

This important feature works like this:

Both number 1 time settings can be placed at any time of

the day, although they would usually be in the morning.

Each of the time settings 2 to 6 can only be placed

between the previous setting and 1:59.

When using the - button to change settings 2 to 6 the

button stops responding when the previous setting time

is reached. While using the + button to change settings

2 to 5, as later settings in the sequence are reached the

time continues to advance, (until 1:59 if the button is held

down), and all later settings reached are then changed to

the same time as the one being set.

Should this happen unintentionally and settings 2 to 6 are

all at the same undesirable time, use the PROG button to

get back to setting 1, days 1 to 5, then review and change

all the times and temperatures to the required settings. If

any times are intentionally set to the same time then the

temperature associated with the higher setting number

will be used to control the room temperature.

INITIAL START-UP

Slide the battery cover to the left to

reveal the programming buttons

(PROG, +, -). Slide the cover further

left to reveal the battery compartment.

Fit the batteries (supplied) making sure

the + ends align with the ⊕ symbols at the back of the

compartment. RESET the TP5E as described below.

The blank display changes to that shown in fig. 1. (If the

actual air temperature in the proximity of the unit is higher

than 20°C the flame symbol will not be displayed). Slide

the battery cover to the right but leave the buttons visible.

RESET

The TP5E may be reset to the factory pre-set programme,

12:00 on day 1, and 20°C by pressing and holding down

the four buttons, temperature s and t , time + and -, until

the display becomes blank. This may be necessary after

a severe electrical storm or serious fluctuations in the

electricity supply, indicated by a malfunction or spurious

information such as 18:88 on the display.

SETTING THE CLOCK

Press the PROG button once; the colon

stops blinking, (see fig. 2). Use the +

and - buttons to set the time. Pressing

and releasing these buttons changes

the time by one minute, holding these

buttons down changes the time quickly.

When the time is correct press the

PROG button to start the clock; now

only the colon and day number are

displayed, (see fig. 3). Use the + and -

buttons to select the correct day

number. (It is intended that day 1 is

Monday, therefore days 6 and 7 are

Saturday and Sunday - the weekend).

Press PROG to display the first setting,

(see fig. 4).

REVIEWING THE EXISTING

SETTINGS

Now each press of the PROG button

shows, in sequence, the twelve set

times and their associated control

temperatures, starting at setting 1, days

1 to 5, and finishing at setting 6, days 6

& 7, (see figs. 4 to 6). Pressing PROG

while setting 6, days 6 & 7 is shown

returns the TP5E to RUN mode.

Produkt Specifikationer

Mærke:	Danfoss
Kategori:	Termostat
Model:	TP5E

Har du brug for hjælp?

Hvis du har brug for hjælp til Danfoss TP5E stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Danfoss Manualer

Danfoss React M30x1.5 Manual

1 Februar 2025

Danfoss React RA click Manual

1 Februar 2025

Danfoss HC6000 Thermostaat Manual

12 Januar 2025

Danfoss ORT-10 Manual

11 Januar 2025

Danfoss RA 2982 Manual

6 Oktober 2024

Danfoss TP5E-RF Manual

23 September 2024

Danfoss TP5 Manual

17 September 2024

Danfoss Ally - Radiator Thermostat Thermostaat Manual

1 September 2024

Danfoss TP5001Range gebruik Manual

25 August 2024

Danfoss RA 2000 series Manual

23 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Vimar 30811.C Manual

31 Oktober 2025

Abus Comfion FUSH80100 Manual

29 Oktober 2025

Delta Dore Tybox 137 Manual

17 Oktober 2025

Delta Dore RF 6600 FP Manual

17 Oktober 2025

Emos P56A01 Manual

15 Oktober 2025

Fantini Cosmi C830RL Manual

14 Oktober 2025

UPM HTM311A Manual

12 Oktober 2025

Bticino NT4451 Manual

8 Oktober 2025

Bticino HS4451 Manual

7 Oktober 2025

Bticino N4451 Manual

7 Oktober 2025