Danfoss TP75 Manual

Danfoss Termostat TP75

Læs gratis den danske manual til Danfoss TP75 (4 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Danfoss TP75, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Electronic Programmable Room Thermostats

TP75 with integral sensor

TP75A with remote sensor

TP75B with remote teleswitch

TP75AB with remote teleswitch and remote sensor

SETTING INSTRUCTIONS

SETTING THE CLOCK

After the recessed RESET button

has been pressed the display

appears as shown, with the colon

blinking, and all the factory pre-set

conditions will be present.

To set the clock to the correct time,

press and release the button marked

PROG. The digits blink.

Press the DAY button (the digits

stop blinking) until the correct day

number is shown. (1 = Monday).

Press and release the + or - buttons to change the time by one

minute, or press and hold down to change the time in ten minute

steps.

When the time is correct press PROG to start the clock and continue

setting sequence.

SETTING THE OSC PERIOD (IF ENABLED)

This display will only appear if the

OSC function has been enabled.

Use the + or - button to select an

OSC period. The choices are 0:30

(30 minutes), 1:00 (one hour), 1:30,

and 2:00.

The recommended initial setting is 0:30, for more details see the

post-commissioning notes in the Installation & Commissioning Guide.

If the OSC period is set to 0:00, the function is disabled.

Press the PROG button to enter

event programming mode.

+1 HR

+2 HR

+3 HR

+1 HR

+2 HR

+3 HR

+1 HR

+2 HR

+3 HR

SETTING THE EVENT

TIMES & TEMPERATURES

The installer will have configured the

TP75 to run in 7 day mode or 5/2 day

mode by means of a switch on the

back of the unit.

The first event (time and

temperature) is displayed, together

with the day (7 day mode) or days (5/

2 day mode) when it is active. Note

that the day number(s) displayed will

reflect the current day.

To step through the six available

events press and release the NEXT

button.

Whilst each event is on display, it

may be altered as required.

continued/....

Control temp.

Event No.

Time

Day

+1 HR

+2 HR

+3 HR

7 day mode

Control temp.

Event No.

Days

Time

+1 HR

+2 HR

+3 HR

5/2 day mode

7 day mode

+1 HR

+2 HR

+3 HR

5/2 day mode

+1 HR

+2 HR

+3 HR

..../continued

Press and hold down the + or - buttons to change the event time in

ten minute steps. Press and release to change by one minute.

Press and release the s button to raise the control temperature by

0·5°C (1°F), or press and release the t button to lower the control

temperature by 0·5°C. Press and hold down these buttons to make

larger changes to the control temperature.

In addition to being able to programme a temperature, it is also

possible to programme an OFF simply by pressing the t button until

the symbol 'OF' appears on the display.

Caution: If OFF is selected, frost protection is not provided.

When all events for the day(s) on

display are as required press DAY to

show the following day's events.

The display will appear similar to one

of the diagrams on the right,

depending on whether the TP75 has

been set up for 7 day or 5/2 day

mode.

Use the + -, , s t, , NEXT buttons to

alter the events as required,

If the previous day's programme is to

be repeated, press COPY to repeat

those events with just one button

press.

(Pressing COPY when in 5/2 day mode will repeat the events

programmed for days 1 to 5 at the weekend).

Use DAY and NEXT to check all the

events programmed, using the + -, ,

s t, , NEXT buttons to make

alterations to each event as

necessary.

When all the events for every day

are as required, press PROG to

return to RUN mode, with the colon blinking.

The heating system will now be controlled to provide the temperatures

programmed. Refer to the USER'S GUIDE for details of the manual

over-rides available during day to day operation.

+1 HR

+2 HR

+3 HR

FACTORY PRE-SET PROGRAMME

The TP75 range of programmable room thermostats are provided with a factory pre-set

programme of switching times and temperatures, so that, once the clock has been set and the

TP75 returned to the RUN mode, the heating system will be controlled at the times and to the

temperatures of the pre-set programme, as shown in the following table and indicated by the

fine line in the diagram below.

The instructions on the previous page show how to change the times and temperatures to the

users requirements.

The table should be used to record the users programme. If the TP75 has been configured for

5/2 day control only days 1 and 6 need be recorded.

Factory Pre-set Programme, and spaces for user’s settings.

Day

Events

1 2 3 4 5 6

Pre-set User’s Pre-set User’s Pre-set User’s Pre-set User’s Pre-set User’s Pre-set User’s

(Monday)