Datalogic Lynx Manual

Datalogic Vugge & Dockingstation Lynx

Læs gratis den danske manual til Datalogic Lynx (2 sider) i kategorien Vugge & Dockingstation. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Datalogic Lynx, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Lynx™ Four Slot Dock

Read this manual carefully before performing any

type of connection from the terminal to a host PC

using the Four Slot Dock.

The user is responsible for any damages caused

by incorrect use of the equipment or by

inobservance of the indication supplied in this

manual.

NOTE

The Four Slot Dock paired with a Lynx PDA builds a reading

system for the collection, decoding and transmission of barcode

data.

The Four Slot Dock can charge both the terminals and the spare

batteries at the same time. The spare batteries (both standard

capacity battery 94ACC0064 and high capacity battery

94ACC0065) can be charged by inserting them into the slots at

the back of the cradle.

The Four Slot Dock comes in two different models, the Charger

(94A150037) and the Ethernet (94A150054).

The Ethernet model also provides Ethernet connection for data

transfer via local area networks.

Figure 1 –Four Slot Dock

Key:

A) Link LED for Ethernet Port 1,2,3,4

B) Battery charger LED for Slot 1,2,3,4

C) Power supply connector

D) Ethernet Port 1 (with integrated Link and Speed LEDs)



E) Ethernet Port 2 (with integrated Link and Speed LEDs)**

F) Power on LED

822001291

 Used in the Ethernet Four Slot Dock only

 Available in the Ethernet Four Slot Dock only

PDA INSERTION/ REMOVAL

For correct insertion into the cradle, insert the mobile computer

from the top of the cradle and push it down.

To remove the mobile computer from the cradle, simply pull it

upwards while holding the cradle firmly down.

Figure 2 - PDA Insertion

Power Supply

Each 4SD requires a power supply to be connected to mobile

computers. We recommend the power supply already included in

the box.

Figure 3 - Power Supply Polarity

LED INDICATORS

Power LED Status Indicator (F)

Colo

Status

Green Cradle powered

Battery Charging LED Status Indicators (B)

Colo

Status

Off Battery absent

Red Battery charge in progress

Green Charge completed

Red Blinking Error

USING THE SPARE BATTERY CHARGER

Insert the battery, contacts side first, into the slot and press it

until the battery latch is automatically closed; charging starts

automatically.

Figure 4 - Spare Battery Insertion

To remove the battery, press the battery-release lever.

Figure 5 - Spare Battery Removal

ETHERNET CONNECTION





The Ethernet cradle drivers are pre-installed on the Lynx and

initiate automatically when the terminal is placed in a properly

connected Four Slot Dock Ethernet.

When the PDA is inserted into the Four Slot Dock Ethernet, the

connectivity icon on the taskbar indicates that the mobile

computer is connected to a network.

The maximum bandwidth capacity for each

Mobile Computer is 12Mbps.

NOTE

The yellow Link LED blinks to indicate activity, or stays lit to

indicate that a link is established. When it is not lit it indicates that

there is no link.

Connections should always be made with power

OFF!

CAUTION

How to connect

Connect the Ethernet cradle (Ethernet port 1 - E) to an Ethernet hub

or to a port on the host device. Connect the Ethernet cradle (power

port - F) to the power supply.

Figure 6 - Ethernet Connection

Key:

A) Ethernet 4 Slot Dock

B) Power supply without power cord, supplied with the 4SD and

country specific power cord

C) UTP CAT 5E cable (recommended use)

D) Ethernet hub

E) Ethernet port 1

F) Power port

 Available in the Ethernet Four Slot Dock only

B F

D E

Daisychaining Ethernet Connection

To connect several cradles to an Ethernet network, the Ethernet

cradles may be daisychained. It is recommended not to connect

more than 4 cradles in order to maintain the optimal baud rate.

Connect the first Ethernet cradle to the Ethernet Switch. Connect the

additional cradles as shown in Figure 7.

Figure 7 - Daisychaining Ethernet Connection

Key:

A) Power supply without power cord, supplied with the 4SD and

country specific power cord

B) Ethernet hub

C) UTP CAT 5E cable (recommended use)

D) Ethernet Port 1

E) Ethernet Port 2

This is a Class A product. In a domestic environment

this product may cause radio interference in which

case the user may be required to take adequate

measures.

WARNING

DOCK CONTACTS CLEANING PROCEDURE

All exterior metal contacts/connectors exposed to spills, dirt or debris

accumulation require periodic cleaning to ensure best performance

during charging and data transmission.

Use a soft, lint-free dry cloth or lens tissue to clean the product

(contacts and plastics). An antistatic cloth is preferable but you can

also use a cotton cloth. Avoid wool, synthetic cloths or other

materials that can cause electrostatic discharges.

If the contacts are very dirty, clean them with a soft cloth moistened

with a diluted non-aggressive cleaning solution or a diluted isopropyl

alcohol solution (20% maximum). A cotton swab may be used only

on hard-to-reach contacts.

Clean the contacts when you see traces of dirt or when you

experience solid connection issues between the terminal and its

dock (device not charging or intermittent communications). It is

however suggested to clean the contacts every 6 months (more

often if the environment is dusty).

If the plastic areas are very dirty use only a cloth dampened with

water.

Do not use abrasive or aggressive cleaning agents

or abrasive pads to clean electric contacts, scan

windows or plastics.

CAUTION

Cleaning the Dock Contacts

1. Remove the power cable before cleaning the contacts.

2. Use a soft dry cloth as suggested above. If the product is very

dirty, moisten the cloth in a non-aggressive cleaning solution or

diluted isopropyl alcohol solution (20% maximum).

3. Gently rub the cloth back and forth ONLY along the contacts,

following the directions indicated by the red arrows. Use care

not to leave any cloth residue.



4. Use a dry cloth to remove any dirt near the contacts area and to

clean the plastic parts. If the plastic parts of the equipment are

very dirty, slightly dampen the cloth with only water.

5. Repeat steps 2, 3 and 4 using a clean dry cloth.

6. Allow the cleaning solution to fully evaporate before powering

up the product.

Cleaning the Dock Auxiliary Battery Contacts

1. Remove the power cable and the Ethernet module before

cleaning the contacts.

2. Use a soft dry cloth as suggested above. If the product is very

dirty, moisten the cloth in a non-aggressive cleaning solution or

diluted isopropyl alcohol solution (20% maximum).

3. Gently rub the cloth back and forth ONLY along the contacts,

following the directions indicated by the red arrows. Use care

not to leave any cloth residue.

4. Use a dry cloth to remove any dirt near the contacts area and to

clean the plastic parts. If the plastic parts of the equipment are

very dirty, slightly dampen the cloth with only water.

5. Repeat steps 2, 3 and 4 using a clean dry cloth.

6. Allow the cleaning solution to fully evaporate before powering

up the product.

TECHNICAL FEATURES

Electrical Features

Power supply * 12 VDC ± 5% @ 5A

Consumption Max 5 A

Spare slot charge time

Std Battery 2h 30

High Cap Battery 4h

Communication Features

Interface Ethernet **

Baud Rate 10/100BASE-T

Physical Features

Dimensions 445 x 135 x 102 mm

17.5 x 5,3 x 4 in

Weight (without

connection cables)

1250 g / 44.1 oz

Indicators Green power-on LED

Bicolored battery charge status LED

Environmental Features

Working temperature*** 0° to +50°C / +32° to +122°F ***

Storage temperature -20° to +70°C / -4° to +158°F

Humidity 95% without condensation

Electrostatic discharge

EN 61000-4-2

4 KV contact / 8 KV air

* Use only DL approved power adapters.

** Available in the Ethernet Four Slot Dock only

*** When inserted in the spare slot, batteries must be charged at a

temperature ranging from 0° to 44 °C.

Never charge the main device or spare batteries in a closed space

where excessive heat can build up.

FCC COMPLIANCE

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to

correct the interference at his own expense.

Modifications or changes to this equipment without the expressed

written approval of Datalogic could void the authority to use the

equipment.

This device complies with PART 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference which may cause

undesired operation.

Protected to the fullest extent under U.S. and international laws. Copying,

or altering of this document is prohibited without express written consent

from Datalogic ADC S.r.l.

Datalogic and the Datalogic logo are registered trademarks of Datalogic

S.p.A. in many countries, including the U.S.A. and the E.U.

Lynx and the Lynx logo are trademarks of Datalogic ADC S.r.l.

All other brand and product names mentioned herein are for identification

purposes only and may be trademarks or registered trademarks of their

respective owners.

A C

D E

Produkt Specifikationer

Mærke:	Datalogic
Kategori:	Vugge & Dockingstation
Model:	Lynx
Bredde:	68 mm
Dybde:	27 mm
Højde:	144 mm
Vægt:	270 g
Produktfarve:	Sort
Batterikapacitet:	1800 mAh
Skærm diagonal:	2.7 "
Skærmopløsning:	320 x 240 pixel
Berøringsskærm:	Ja
Kompatible hukommelseskort:	microSD (TransFlash),microSDHC
Wi-Fi:	Ja
Datanetværk:	HSPA+
Bluetooth:	Ja
Batteriteknologi:	Lithium-Ion (Li-Ion)
Opbevaringstemperatur (T-T):	-20 - 70 °C
Wi-Fi-standarder:	802.11b,802.11g,Wi-Fi 4 (802.11n)
Driftstemperatur (T-T):	0 - 50 °C
Sikkerhedsalgoritmer:	CCX v4
Skærm:	LCD
Intern hukommelse:	0.256 GB
Operativsystem installeret:	Windows Embedded Handheld 6.5
Bluetooth-version:	2.0+EDR
GPS (satellit):	Ja
Processorfrekvens:	0.806 GHz
Processorserie:	PXA 310
Intern hukommelsestype:	RAM
Flash-hukommelse:	0.512 GB
Grænseflade:	micro USB, RS-232
Vis antal farver:	262.144 farver
Driftsfrekvens:	800, 850, 900, 1900, 2100 Mhz
Tastaturopsætning:	QWERTY
Tastatur antal taster:	46
RFID-læser:	Ingen
Stregkodelæser:	Ja