Datalogic QuickScan QS6000 Plus Manual

Datalogic Stregkodelæser QuickScan QS6000 Plus

Læs gratis den danske manual til Datalogic QuickScan QS6000 Plus (16 sider) i kategorien Stregkodelæser. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Datalogic QuickScan QS6000 Plus, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

Electronic Article Surveillance (EAS)

Installation Instruction Manual

Introduction

The EAS option enables nners toQuickScan QS6000 Plus model sca

provide Electronic Article Surveillance (EAS) deactivation.

This document provides information and procedures to install a new

EAS Antenna Upgrade Kit, or to replace a malfunctioning loop antenna

already installed in the canner. s

The EAS upgrade or replacement of the loop antenna in the scanner

involves:

• Replacing the Scan Window with a new thinner Scan Window

and the EAS Loop Antenna;

• Replacing the Handle Printed Circuit Board (PCB) with one that

contains a connector for the EAS Antenna leads, and

• Replacing the Interface Cable with a special EAS Interface Cable.

The loop antenna connects to the store’s EAS System through this special

Interface Cable

Before installing the upgrade or replacing the EAS antenna, verify that

your EAS Upgrade Kit contains the following items shown in Figure 1.

Scan Window

Loop Antenna

To EAS System

EAS/Interface

Cable

Figure 1. EAS Kit

1. Scan Window/

EAS Antenna.

2. Handle PCB.

3. Insulation Tape Strip

4 . This Instruction Sheet

You should also have the correct

EAS/Interface cable that matches

your POS Terminal connection.

QuickScan® QS6000 Plus

Tools Required

You need the following tools to upgrade or replace the EAS

Antenna:

• Torque Limiting Driver.

• T8 Torx® bit.

• Multimeter (or equivalent) to test for continuity.

• ESD (ElectroStatic Discharge) protection as described below.

• .050 hex driver

ElectroStatic Discharge Protection

To protect static sensitive circuitry, follow these ElectroStatic Discharge

(ESD) procedures when upgrading, or servicing an existing EAS antenna.

Figure 2 shows the ESD materials.

Figure 2. ESD Setup

ESD Procedures:

1. Connect the above ESD components together with a common

ground strap to eliminate any electrical potential.

2. Use the anti-static floor and table mats to neutralize the working

area (floors, carpeting, tables, etc.).

3. Use the anti-static wrist strap to eliminate buildup static charge

picked up from the environment (shoes on carpets, etc.).

4. Attach the anti-static ground clip to a known ground point.

PSC and the PSC logo are registered Trademarks of PSC INC.

QS6000/6000 PLUS

a trademark owned by PSC, Inc. Torx® is a registered trademark of Camcar Textron.

ESD Materials:

1. Anti-static tablemat

2. Anti-static wriststrap

3. Anti-static floormat

4. Earth Ground

Alerts you to use

ESD protection.

Torx® is a registered trademark of Camcar Textron.

Produkt Specifikationer

Mærke:	Datalogic
Kategori:	Stregkodelæser
Model:	QuickScan QS6000 Plus

Har du brug for hjælp?

Hvis du har brug for hjælp til Datalogic QuickScan QS6000 Plus stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Stregkodelæser Datalogic Manualer

Datalogic Magellan 8302 Manual

11 Januar 2025

Datalogic CBX500 Manual

9 Oktober 2024

Datalogic PowerScan 7000 2D Manual

22 September 2024

Datalogic Matrix 120 Manual

12 September 2024

Datalogic PSHD-8000 Manual

30 August 2024

Datalogic CBX800 Manual

6 August 2024

Datalogic PowerScan PD9530 Manual

3 August 2024

Datalogic Magellan 800i Manual

3 August 2024

Datalogic Kyman Gun 700-601 Manual

3 August 2024

Datalogic Magellan 1000i Manual

1 August 2024

Stregkodelæser Manualer

Nyeste Stregkodelæser Manualer

Brady V3200 Manual

16 Juni 2025

Code Corporation CR1500 Manual

15 Juni 2025

Approx appLS25WS Manual

24 Marts 2025

Approx appLS24 Manual

24 Marts 2025

Cognex DataMan 50 Manual

26 Februar 2025

Unitech MS852N Manual

23 Februar 2025

23 Februar 2025

23 Februar 2025

23 Februar 2025

23 Februar 2025