Delta Dore Tyxia 5730 Manual

Delta Dore Modtager Tyxia 5730

Læs gratis den danske manual til Delta Dore Tyxia 5730 (1 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Delta Dore Tyxia 5730, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Recommendations

• IMPORTANT: the control wires are not

insulated from the mains power supply.

All connected equipment must be marked

CE and meet the requirements of the

low voltage devices as well as assembly

recommendations.

Local control wires can be extended

up to 10 m (separate from the 230 V).

• The roller shutter high and low stops must

be set before the receiver is installed.

1 - Installation

1.1 Connection instructions for terminals 1 2 3 4.

- Strip the wires while respecting the strip

length speciﬁed on the product.

- Push the wire fully into the terminal.

1.1.1 Solid wires Stranded wires 1.1.2

1.2 Connection instructions for IN1 - COM - IN2 terminals

- Use the wires supplied.

- Push the wire fully into the terminal.

1.3 Connection

- Connect the motor control wires to terminals 3 and 4

(motor lowering control wire to terminal 3, raising control wire to terminal 4).

- Connect the switch to the IN1 - COM - IN2 terminals.

- Connect the 230 V power supply to terminals 1 and 2.

- Switch the installation power back on to continue with the association operation.

2 - Association

3 - Configuration

Conﬁgure the receiver according to

the type of switch connected.

Mode 1 (by default): Hold switch

Raise/Stop/Lower

Mode 2: Raise/Lower

double push-button

Raise + Lower: Stop

Mode 3: Raise/Stop/Lower/Stop

push-button

To modify the receiver conﬁguration.

- Press the receiver's button for 6 seconds.

- The LED ﬂashes, then becomes steady, release.

The number of ﬂashes corresponds

to the current mode.

- Brieﬂy press the receiver button to select the mode.

- Conﬁrm the selected mode by pressing the button

for 3 seconds until the LED switches off.

4 - Learning for the shuer travel time

Perform a complete cycle from stop to stop:

1- Lower or raise the roller shutter completely to the stop.

2- Do the reverse action until the opposite stop is reached.

Note:

The learning for the shutter travel time adjusts itself automatically for each complete

cycle from stop to stop.

If the motor has 4 wires (Live/Neutral/Raise/Lower) or if the power of the connected

motor is less than 45 W, or if an electronic motor is ﬁtted (e.g. Hard-wired Tymoov),

Tyxia 5630/5730 cannot perform automatic learning for the shutter travel time.

The receiver or receivers must be conﬁgured in “manual learning mode” (see additio-

nal instructions on the Tyxia 5630-5730 pages on the DELTADORE site).

5 - Troubleshooting

Summary of functions accessible using the receiver button:

0,75 - 1,5 mm

> 6 s

TYXIA

1234

TYXIA

1234

TYXIA

1234

TYXIA

Technical characteristics

- Power supply: 230 V~ 0.6 VA

- 2 powered contact outputs: TYXIA 5630 (1 A) - TYXIA 5730 (2 A)

- Stand-by consumption: 0.06 W

- Number of associated transmitters: 16 maximum

- Storage temperature: -10°C/+70°C

- Operating temperature: -10°C/+40°C

- IP 40 (ﬂush mounting box)

- Dimensions: 41 x 36 x 14.5 mm

- X3D wireless remote control device: 868.7 MHz to 869.2 MHz

- Maximum radio power < 10 mW

- Receiver category: 2

Receiver

for roller shutter

Use an electrically

isolated tool to perform

the actions on the

receiver conﬁguration

button.

TYXIA

IPx4

230V~

OFF

Switch off the installation

power supply

You can install the receiver for roller shutter

in a ﬂush-mounted box behind a switch or

control push-button or in a sealed box inside

the roller shutter, a safe distance from metal

parts.

Removal recommendations

- Switch off the power supply.

- Use the tool supplied or a 2.5 mm screw-

driver to press the button of the front

terminal before removing the wire.

Removal recommendations

Turn the wire while pulling on it.

Do not strip the wires when they

are connected to the product as you

could damage the internal connector.

123 4

7mm

0,5 mm

KY31A02

123 4

230 V~

IN1

COM

IN2

1 2 3 4

TYXIA

1 2 3 4

IN1

COM

IN2

IN1

COM

IN2

IN1

COM

Hold switch

Double

push-button

Push

button

- Press and hold the receiver

button for 3 seconds until the

LED ﬂashes, release.

On the transmitter:

- Send the association command

(Refer to the user guide).

When the receiver LED has stopped

ﬂashing. The products are associated.

OFF

1 2 3 4

TYXIA

1 2 3 4

... ... ...

> 3s

1 2 3 4

TYXIA TYXIA

TYXIA 2600

TYDOM

COM

IN1

IN2

CR 2032

TYXIA

2600

> 3s

A B

> 3s

IN1

COM

IN2

IN1

COM

IN2

IN1

COM

Do not interrupt the roller shutter travel.

Mode 1

Hold

switch

Mode 2

Double

push-button

Mode 3

Push button

3’’

> >6’’ 10’’ 20’’ 30’’> >

C D

Association Remove an asso-

ciation

Remove

all associations

Conﬁguration Factory

reset

• Quick press on the button.

Checking the transmitter operating mode.

Brieﬂy press the button.

The LED ﬂashes:

- 1 red ﬂash: MODE 1 Hold switch

(Raise/Stop/Lower).

- 2 red ﬂashes: MODE 2 Double push-button

(Raise/Lower).

- 3 red ﬂashes: MODE 3 Single push-button

(Raise/Stop/Lower/Stop).

• Press and hold the button for x seconds.

Association (refer to §2)

- Press the receiver button for 3 seconds until

the LED ﬂashes. Release

Conﬁguration (refer to §3)

- Press the receiver's button for 6 seconds. The

LED ﬂashes, then becomes steady, release.

Remove an association

(the removal method varies according

to the transmitter associated, refer to the

transmitter's user guide)

Example of removing a remote control

association.

On the receiver:

- Press the receiver button for 10 seconds until

the LED ﬂashes rapidly, release.

On the remote control:

- Press the

and buttons for 3 seconds.

- Make sure that the receiver LED has stopped

ﬂashing. The products are no longer asso-

ciated.

Remove all associations

- Press the receiver's button for 20 seconds.

- Press and hold until the LED switches off after

the rapid ﬂashing phase.

- Release. The receiver has no wireless connec-

tion.

Factory reset

- Press the receiver button for 30 seconds,

the LED ﬂashes then switches off,

The receiver has no wireless connection and

the conﬁguration is reset (mode 1 by default).

An additional user guide is available on the

TYXIA 5630 and TYXIA 5730 pages

of the DELTA DORE website.

www.deltadore.com

Support

The receiver locks in off mode

When an overload is detected, the product locks in off mode for 30

seconds before authorising a new activation.

The LED ﬂashes rapidly throughout this phase.

For TYXIA 5630 receivers:

- Replace your receiver with a TYXIA 5730.

For TYXIA 5730 receivers:

- Contact our customer service.

20A circuit breaker

max. required.

Using the tool supplied

or a 2.5 mm screwdriver,

press the terminal button

then insert the wire.

TYXIA 5630 - TYXIA 5730

20 A

max.

Produkt Specifikationer

Mærke:	Delta Dore
Kategori:	Modtager
Model:	Tyxia 5730

Har du brug for hjælp?

Hvis du har brug for hjælp til Delta Dore Tyxia 5730 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Delta Dore Manualer

Delta Dore RF 7210 Manual

23 September 2025

Delta Dore Delta 8000 BT Manual

15 August 2024

Delta Dore Tyxia 4600 Manual

14 August 2024

Delta Dore Tybox RF 6700 FP Manual

14 August 2024

Delta Dore Tyxia 5612 Manual

13 August 2024

Delta Dore Tyxia 4801 Manual

13 August 2024

Delta Dore Tyxia 5610 Manual

13 August 2024

Delta Dore Tyxia 4620 Manual

13 August 2024

Delta Dore Tyxia 4860 Manual

12 August 2024

Delta Dore RF 6420 Manual

12 August 2024

Modtager Manualer

Nyeste Modtager Manualer

DS18 FRP-4K4 Manual

5 November 2025

DS18 FRP-2.4K4 Manual

5 November 2025

Nady PRA-8 Manual

4 November 2025

Blustream SP24AB-8K Manual

4 November 2025

DS18 FRP-8K Manual

4 November 2025

DS18 FRP-1.2K4 Manual

4 November 2025

Fosi Audio BOX X1 Manual

4 November 2025

BINIZE AO-BOX Manual

4 November 2025

Kohler K-99696-NA Manual

3 November 2025

Sommer 4796V000 Manual

3 November 2025