Delta Dore Tyxia 5731 Manual

Delta Dore Modtager Tyxia 5731

Læs gratis den danske manual til Delta Dore Tyxia 5731 (1 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Delta Dore Tyxia 5731, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Recommendations

• IMPORTANT: the control wires are not

insulated from the mains power supply.

All connected equipment must be marked

CE and meet the requirements of the

low voltage devices as well as assembly

recommendations. Local control wires can

be extended up to 10 m

(separate from the

230 V).

• The roller shutter high and low stops must

be set before the receiver is installed.

• For the control of electric motors, please

1 - Installation

1.1 Connection instructions for terminals 1 2 3 4.

- Strip the wires while respecting the strip length

speciﬁed on the product.

- Push the wire fully into the terminal.

1.1.1 Solid wires Stranded wires 1.1.2

1.2 Connection instructions for IN1 - COM - IN2 terminals

- Use the wires supplied.

- Push the wire fully into the terminal.

1.3 Connection

- Connect the motor control wires to terminals 3 and 4

(motor lowering control wire to terminal 3, raising control wire to terminal 4).

- Connect the switch to the IN1 - COM - IN2 terminals.

- Connect the 230 V power supply to terminals 1 and 2.

- Switch the installation power back on to continue with the association opera-

tion.

2 - Association

3 - Conﬁguration

Conﬁgure the receiver according to

the type of switch connected.

Mode 1: Hold switch

Raise/Stop/Lower

Mode 2 (by default):

Raise/Lower double push-button

Raise + Lower: Stop

Mode 3: Raise/Stop/Lower/Stop

push-button

To modify the receiver conﬁguration.

- Press the receiver's button for 6 seconds.

- The LED ﬂashes, then becomes steady, release.

The number of ﬂashes corresponds

to the current mode.

- Brieﬂy press the receiver button to select the mode

- Conﬁrm the selected mode by pressing the button for 3 seconds until the LED

switches off.

4 - Learning for the shutter travel time

Perform a complete cycle from stop to stop:

1- Lower or raise the roller shutter completely to the stop.

2- Do the reverse action until the opposite stop is reached.

Note: The learning for the shutter travel time adjusts itself automatically for

each complete cycle from stop to stop.

5 - Learning for the tilt time

Do not carry out this operation,

if the TYXIA 5731 controls an awning.

- Hold down the receiver button

for 9 seconds, the LED switches off,

then release. The shutter is positioned at the

midpoint of its height

- Press and hold the rotation button

(step by step mode) until the shutter

has rotated fully, then press stop.

- The tilt time is recorded.

6 - Help

Summary of functions:

0,75 - 1,5 mm

1234

> 6 s

TYXIA

1234

TYXIA

1234

TYXIA

1234

TYXIA

Use an electrically

isolated tool to

perform the actions

on the receiver conﬁ-

guration button.

IPx4

230V~

OFF

Switch off the

installation

power supply

You can install the receiver for roller shutter

in a ﬂush-mounted box behind a switch or

control push-button or in a sealed box inside

the roller shutter, a safe distance from metal

parts.

Removal recommendations

- Switch off the power supply.

- Use the tool supplied or a 2.5 mm screwdriver

to press the button of the front terminal before

removing the wire.

Removal recommendations

Turn the wire while pulling on it.

Do not strip the wires when they are

connected to the product as you

could damage the internal connector.

123 4

7mm 0,5 mm

KY31A02

123 4

230 V~

IN1

COM

IN2

1234

TYXIA

1 2 3 4

IN1

COM

IN2

IN1

COM

IN2

IN1

COM

Hold switch

Double

push-button

Push

button

- Press and hold the receiver but-

ton for 3 seconds until the LED

ﬂashes, release.

On the transmitter:

- Send the association command

(Refer to the user guide).

When the receiver LED has

stopped ﬂashing.

The products are associated.

OFF

1 2 3 4

TYXIA

1 2 3 4

... ... ...

> 3s

1 2 3 4

TYXIA TYXIA

TYXIA 2600

TYDOM

COM

IN1

IN2

CR 20 32

TYXIA

2600

> 3s

A B

> 3s

1 2

IN1

COM

IN2

IN1

COM

IN2

IN1

COM

Do not interrupt

the roller shut-

ter travel.

Mode 1

Hold

switch

Mode 2

Double

push-button

Mode 3

Push button

• Quick press on the button.

Checking the receiver

operating mode.

Brieﬂy press the button.

The LED ﬂashes:

- 1 red ﬂash: MODE 1

- 2 red ﬂashes: MODE 2

- 3 red ﬂashes: MODE 3

• Press and hold the button for

x seconds.

Association (refer to §2)

Conﬁguration (refer to §3)

Learning for the tilt time

(refer to §5)

Removing an association

- Press the receiver's button for 12

seconds. (the removal method varies

according to the transmitter associated,

refer to the transmitter's user guide)

Removing all associations

- Press the receiver's button for 20

seconds.

- Press and hold until the LED switches off

after the rapid ﬂashing phase.

- Release. The receiver has no wireless

connection.

Factory reset

- Press the receiver button for 30 seconds,

the LED ﬂashes then switches off. The

receiver has no wireless connection and

the conﬁguration is reset (mode 1 by

default).

The receiver locks in off mode.

When an overload is detected, the product

locks in off mode for 30 seconds before autho-

rising a new activation. The LED ﬂashes rapidly

throughout this phase.

Contact our customer service.

20A circuit breaker

max. required.

3’’

> > >6’’ 9’’ 20’’>12’’ 30’’>

C D F G

Association Removing an

association

Conﬁguration

Factory

reset

Removing

all associations

Tilt

time

Using the tool supplied

or a 2.5 mm screwdriver,

press the terminal button

then insert the wire.

For the warranty and protection of your

shutters, we recommend the installation

of a wind sensor.

P/N: 6351393

50%

TYXIA

>9s

Technical characteristics

- Power supply: 230 V~ 0.6 VA

• 2 Powered contact outputs: 2A

- Stand-by consumption: 0.06 W

- Number of associated transmitters:

16 maximum

- Storage temperature: -10°C/+70°C

- Operating temperature:

-10°C/+40°C

- IP 40 (ﬂush mounting box)

- Dimensions: 41 x 36 x 14.5 mm

- X3D wireless remote control device:

868.7 MHz to 869.2 MHz

- Maximum radio power < 10 mW

- Receiver category: 2

EN - Receiver for Blackout Blinds

TYXIA 5731

www.deltadore.com

Produkt Specifikationer

Mærke:	Delta Dore
Kategori:	Modtager
Model:	Tyxia 5731

Har du brug for hjælp?

Hvis du har brug for hjælp til Delta Dore Tyxia 5731 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Delta Dore Manualer

Delta Dore RF 7210 Manual

23 September 2025

Delta Dore Delta 8000 BT Manual

15 August 2024

Delta Dore Tyxia 4600 Manual

14 August 2024

Delta Dore Tybox RF 6700 FP Manual

14 August 2024

Delta Dore Tyxia 5612 Manual

13 August 2024

Delta Dore Tyxia 4801 Manual

13 August 2024

Delta Dore Tyxia 5610 Manual

13 August 2024

Delta Dore Tyxia 4620 Manual

13 August 2024

Delta Dore Tyxia 4860 Manual

12 August 2024

Delta Dore RF 6420 Manual

12 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Nady PRA-8 Manual

4 November 2025

Blustream SP24AB-8K Manual

4 November 2025

DS18 FRP-8K Manual

4 November 2025

DS18 FRP-1.2K4 Manual

4 November 2025

Fosi Audio BOX X1 Manual

4 November 2025

BINIZE AO-BOX Manual

4 November 2025

Kohler K-99696-NA Manual

3 November 2025

Sommer 4796V000 Manual

3 November 2025

PEMP E70 Manual

3 November 2025

Taramp’s The Big Boss 8 Bass Manual

3 November 2025