DeWalt DWHTGR50 Manual

DeWalt Limpistol DWHTGR50

Læs gratis den danske manual til DeWalt DWHTGR50 (1 sider) i kategorien Limpistol. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om DeWalt DWHTGR50, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Ceramic Glue Gun

DWHTGR50

Glue Gun Instruction Leaflet

CAUTION:

Read Safety Rules and Operating

Instructions Carefully

WARNING:

Safety Precautions:

• Do not touch nozzle area of glue gun or melted glue.

• Do not make repairs to the glue gun.

• Do not use a damaged glue gun.

• Do not allow glue gun to come in contact with water, liquids or rain.

• Do not carry the tool by the cord or pull cord to disconnect it

from the outlet.

• For interior use only.

• Do not leave the glue gun unattended during use.

• Do not attempt to remove unused glue from the glue gun after use.

• Place the glue gun in the upright position when idle using the fold

down stand provided.

• Do not use this product in areas where the risk of explosion is present.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similar qualified persons in order to avoid a hazard.

When using electric tools, basic safety precautions

should always be followed to reduce the risk of fire,

electrical shock and personal injury.

READ ALL SAFETY INSTRUCTIONS:

1. Keep children away.

2. Do not touch the nozzle area or melted glue.

3. Keep work area clean. Work environment should be clean, dry

well lit and clear of flammable materials.

4. Guard against electric shock. Prevent body contact with grounded

surfaces like pipes and appliances. Do not use near water.

5. Inspect extension cords.

6. Always use safety glasses.

7. Don’t abuse cord. Never carry the tool by the cord or yank the

cord to disconnect from plug or receptacle.

8. Disconnecti tools when not in use.

9. Avoid accidental glue discharge. Do not touch the glue stick or

trigger except to dispense glue.

10. To reduce the risk of fire or electric shock, do not expose this

product to rain or moisture.

11. When not in use, the tool should be stored indoors.

12. Do not pull glue sticks from gun. The feed mechanism may

become damaged or impaired. If you desire to change types of

glue, cut off protruding end and feed the remainder through with

the new type of glue.

13. This appliance has a polarized plug (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended

to fit in a polarized outlet only one way. If the plug does not fit

fully in the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician. Do not modify the plug in any way.

OPERATING INSTRUCTIONS

IMPORTANT: Please read carefully before using your

electric glue gun

1. Plug your glue gun into an electrical outlet.

2. To open the fold-away stand, take hold of the flanges on both sides

of the stand and pull forward, until the stand locks into position.

3. Insert standard (1/2” inch or 12mm diameter) glue stick. Two glue

sticks are needed for first time use.

4. Wait 2 minutes for the glue and glue gun to heat up intially.

5. Glue is fed by simply pulling the trigger. Amount of glue is

determined by how far the trigger is pulled.

6. Unplug tool after use if it will not be used within a 30 minute period.

7. Do not attempt to remove unused adhesive from the gun after

use. Any unused adhesive can be stored in the gun, reheated

and used later.

TIPS ON USING

1. The working time of the hot melts can be extended to 50 to 60

seconds by applying the adhesive in large drops (1/2” diameter)

or shortened to less than 10 seconds by extruding the adhesive

in thin lines.

2. Large areas are difficult to bond because the adhesive frequently

will harden before you have extruded the required amount.

3. Preheat surfaces (especially metals) to improve bond strength.

Direct sunlight will accomplish this.

4. The adhesive remaining in an unheated glue gun will

remelt upon heating.

5. Do not use items that will be subjected to temperatures above

140˚ F (60˚ C).

6. Do not use hot melt to hold heavy loads.

7. Some paints and stains can weaken the adhesive. You may need

to paint or stain before gluing.

Available Stanley

Glue Sticks for this Glue Gun

ELECTRIC RATING:

INPUT: 120 VAC 60Hz

POWER: 50W

WARNING:

WHEN GUN IS HOT, DO NOT LAY IT ON ITS SIDE.

MELTED GLUE WILL BURN SKIN.

OPERATING TEMPERATURE OF THE NOZZLE IS 380°F (193°C).

DO NOT TOUCH THE NOZZLE OR MELTED GLUE.

THIS TOOL MUST BE PLACED IN ITS STAND WHEN NOT IN USE.

APPLICATIONS AND REPAIRS

• Woodworking

• Plastics

• Foam

• Fabrics

• Crevices

• Paper

• Sealingwindows, tiles & bathroom fixtures

• Repair bookbindings, shoe or loose carpeting

• Dried floral arrangement

• Electrical insulation

• Cardboard

79002772

701 East Joppa Road, Baltimore, MD 21286

1-800-4-DEWALT (1-800-433-9258)

GS15DT

GS20DT

GS25DT

GS230S

GS230-24

GS230-3

GS220-BK

GS220-24

GS240-24

GS260

GS264BK

GS500

Dual Melt: for bonding heat sensitive

material, as well as general

All Purpose: Clear sticks for fast

repairs and hobby projects.

All Purpose Transparent:

Sticking on wood, leather

Electrical: for sticking on cables, electic

leads, PVC, carpet floor covering

Wood Working: transparent Hot Melt glue

Super Strength: for stronger bond in

a wide variety of materials

Part No

Applications

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Limpistol
Model:	DWHTGR50

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DWHTGR50 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Limpistol DeWalt Manualer

DeWalt DCGG581 Manual

29 Juli 2025

DeWalt DWHTGR50 Manual

3 September 2024

DeWalt DCE560 Manual

29 August 2024

DeWalt DC547 Manual

16 Oktober 2022

Limpistol Manualer

Nyeste Limpistol Manualer

Rapid EG Point EG130 Manual

6 Oktober 2025

Rapid G1000 Manual

6 Oktober 2025

Draper 70836 Manual

2 Oktober 2025

NEO Tools 17-096 Manual

29 September 2025

NEO Tools 17-084 Manual

29 September 2025

NEO Tools 17-083 Manual

28 September 2025

Draper 03359 Manual

23 September 2025

Draper D20 18097 Manual

23 September 2025

Draper Expert 16157 Manual

23 September 2025

Cocraft HG 200 Manual

7 September 2025