Ditek DTK-RM24EXTS Manual

Ditek Netværkskort/adapter DTK-RM24EXTS

Læs gratis den danske manual til Ditek DTK-RM24EXTS (2 sider) i kategorien Netværkskort/adapter. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Ditek DTK-RM24EXTS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DITEK Technical Support

1-888-472-6100 www.diteksurgeprotection.com

DITEK Corporation

ONE DITEK CENTER

1720 Starkey Road

Largo, FL 33771

This Surge Protective Device (SPD) is a high performance device, designed to provide protection

for sensitive electronic loads connected to service panels, fire panels, or where the SPD is

directly connected to the electronic device. Maximum protection will only be achieved if the SPD

is properly installed. Please read and follow the installation instructions carefully.

NOTICE: This SPD should be installed by a licensed contractor in accordance with the National

and Local Electrical Codes and the following instructions.

APPLICATION

Rack mount surge suppression for shielded Ethernet, PoE and PoE extender circuits with field replaceable

surge modules (DTK-NETMS, DTK-EXTMS).

INSTRUCTIONS

Note: This device is intended to be installed indoors on the equipment rack closest to the point of use.

1. Test circuit prior to install to verify correct operation.

2. Turn off the power to the equiment to be protected.

3. This device can be mounted in a standard 19” equipment rack, or wall mounted using a hinged wall

mount bracket.

4. Connect to equipment ground using the ground lug provided on rear of faceplate. Use a minimum

#10 AWG wire.

Make sure the ground wire is as short as possible.

Max ground resistance is 25 Ohms, 5 Ohms or less is optimum.Ground Resistance Rule:

This cannot be an assumed value and must be measured to assure proper grounding.

5. Plug the RJ45 tipped cable from the field or supply wiring to the “IN” UNPROTECTED

RJ45 jack.

6. Plug a 3’ RJ45 male to RJ45 male patch cable from the RJ45 jack to the“OUT” PROTECTED

equipment to be protected. The 3’ patch cable will give this device time to react.

7. After all connections have been made and no hazards exist, restore power to the equipment.

Surge Module Install/Replacement: There is no need to remove this protector from the rack, the

surge modules can be installed/replaced while it is mounted.

This product is made up of 12, 16 or 24 individual surge modules.

If 1 or more channels self sacrifice, or go end of life, you can replace that module as follows:

1. Power down the individual circuit before servicing this device.

2. Insert a 3/8“ wide flat blade screwdriver into the top notch of the module’s bezel.

3. Gently turn the screwdriver to the right to loosen the bezel.

4. Insert the screwdriver into the bottom notch and again gently turn the screwdriver to the right until the

module is free of the mating connector located at the rear of the rack mount chassis.

5. Remove module or blank bezel for new install.

6. Insert new surge module into openening aligning the surge module with the integrated card guides.

The orientation should match the revious module.

7. Press the new surge module in place making sure it is seated completely and the bezel is flush with the

rack mount chassis.

8. Connect the RJ45 cables as mentioned in #5 and #6 of the listed above.INSTRUCTIONS

9. After all connections have been made and no hazards exist, restore power to the circuit.

Please see the illustrations page for more details.

Doc # INT-100174-001

Part No. 191605 Rev. 1

Drawn By: B. Aycock 4-27-18

Created By: R. Mitchell 4-30-18

INSTALL INSTRUCTIONS

DTK-RM12NETS, DTK-RM16NETS, DTK-RM24NETS

DTK-RM12EXTS, DTK-RM16EXTS, DTK-RM24EXTS

Note: The grounding detail for field installed network surge protectors is not applicable when a shielded

protector using STP (Shielded Twisted Pair), with properly tipped shielded RJ45 connectors, has been

terminated at a properly mounted and grounded shielded rack mount surge protector. The shield is used

to dissipate the excess overvoltage. For example, DTK-MRJPOES, shielded single channel protector, use

DTK-RM12NETS, DTK-RM16NETS or DTK-RM24NETS shielded rack mount multi-channel protector.

INSTALLATION

Produkt Specifikationer

Mærke:	Ditek
Kategori:	Netværkskort/adapter
Model:	DTK-RM24EXTS

Har du brug for hjælp?

Hvis du har brug for hjælp til Ditek DTK-RM24EXTS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Netværkskort/adapter Ditek Manualer

Ditek DTK-120SLR Manual

28 September 2025

Ditek DTK-VM12RM Manual

30 Januar 2025

Ditek DTK-RM24EXTS Manual

30 Januar 2025

Ditek DTK-2MHLP24BWB Manual

30 Januar 2025

Ditek DTK-2LVLPLV Manual

30 Januar 2025

Netværkskort/adapter Manualer

Nyeste Netværkskort/adapter Manualer

Lindy 43340 Manual

18 December 2025

Planet ENW-2QSFP28 Manual

17 December 2025

Simply45 S45-2012U Manual

7 December 2025

Approx APPUSB900 Manual

29 November 2025

D-Link DWA-548 Manual

29 November 2025

EXSYS EX-62026POE Manual

28 November 2025

Digitus DA-70852 Manual

28 November 2025

Atlantis Land NetPower 502 AV Manual

28 November 2025

EXSYS EX-62010POE-SFP Manual

28 November 2025

D-Link DWA-140 Manual

27 November 2025