Ditek DTK-UPS800 Manual

Ditek UPS DTK-UPS800

Læs gratis den danske manual til Ditek DTK-UPS800 (2 sider) i kategorien UPS. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Ditek DTK-UPS800, eller vil du spørge andre brugere om produktet?

Side 1/2
Line Interactive UPS
400V VAA-800
Inspection
The following items are inside the box:
UPS unit User manual USB cable
Remove the and inspect UPS from its package it for damage that
may have occurred during shipping. If any damage is discovered,
re-pack the unit and return it to the place of purchase.
Connect to Utility Power
Connect AC power cord to utility power. he UPS will Tbegin
charging the internal battery s allow the battery to . For best result ,
charge 6 hours prior to initial use.for a minimum of
Connect /Computer Ethernet
This UPS provides surge protection for a single Ethernet
connection. Remove existing Ethernet cable from PC and insert
into UPS “IN” . connector Using an additional Ethernet cable,
insert into PC network adapter and UPS “OUT” connector.
Battery backup outlets
AC input
Fuse/Circuit breaker
USB com. port
Ethernet surge protection
Plug in Equipment
Plug your equipment to Battery Backup Outlets on the rear panel of
the UPS.
NOTE: Make the allsure that UPS is on to protect powered
important from devices data loss power failure. during
CAUTION: NEVER connect a laser printer or scanner to the
battery of UPS. The backup outlets equipment may draw
significantly power to overload UPS. the
Connect USB Cable and Install Software
Connect one end of the other to the USB cable to PC and the USB
port the rear of the UPS. at
Download the latest version of ViewPower software USB from
https://www.diteksurgeprotection.com/ups-software.html to your
hard drive. Follow on-screen instructions to complete the software
installation.
Operation Display
UPS
Mode LCD Description
UPS
Power on
When UPS is powered
on, it will enter this mode
for 4 seconds.
AC Mode
When AVR is
functioning, icon will
flash every second.
LCD information will be
displayed in the following
order when LCD is
touched.
1. Output voltage
2. Input voltage
3. Load level
4. Battery capacity
Overload
in AC
mode icon will flash.
When overload occurs,
alarm will beep every 0.5
second.
Battery
Mode
When battery level is
low, icon will flash.
Alarm will beep every 10
seconds and LCD
information will be
displayed in the following
order when LCD is
touched.
1. Output voltage
2. Input voltage
3. Load level
4. Battery capacity
Overload
in battery
mode icon will flash.
When overload occurs,
alarm will beep every 0.5
second.
NOTE: If shuts off, you thebacklight may it activate by touching
screen.
Fault Code Table:
Fault condition LCD Solutions
Output short
circuited
Disconnect short-circuited loads
and restart the UPS again.
Overload fault Disconnect all output loads and
restart the UPS again.
Overcharge Call for service immediately.
Bad or severely
discharged battery
Please replace the battery.
High output voltage
fault
Call for service immediately.
Over-temperature Turn off the unit and wait for1.
cooling.
2. Or remove excessive loads
and wait for cooling.
If fault alarm occurs, please call for service immediately.
www.diteksurgeprotection.com 1-800-753-2345
INT-100177-001 PN: 191-608 REV 01


Produkt Specifikationer

Mærke: Ditek
Kategori: UPS
Model: DTK-UPS800

Har du brug for hjælp?

Hvis du har brug for hjælp til Ditek DTK-UPS800 stil et spørgsmål nedenfor, og andre brugere vil svare dig




UPS Ditek Manualer

Ditek

Ditek DTK-UPS Manual

30 August 2024
Ditek

Ditek DTK-UPS800 Manual

30 August 2024

UPS Manualer

Nyeste UPS Manualer

APC

APC RBC150 Manual

2 April 2025
APC

APC RBC151 Manual

2 April 2025
APC

APC RBC145J Manual

29 Marts 2025
APC

APC RBC140J Manual

29 Marts 2025
APC

APC AP9922 Manual

29 Marts 2025
APC

APC RBC148 Manual

29 Marts 2025
Teltonika

Teltonika BAT120 Manual

30 Januar 2025
APC

APC BX1000M Manual

30 Januar 2025
APC

APC BX850 Manual

30 Januar 2025