Doepfer A-140-2 Manual

Doepfer Ikke kategoriseret A-140-2

Læs gratis den danske manual til Doepfer A-140-2 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Doepfer A-140-2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
A-140-2 Dual ADSR
Position and function of the jumpers and connectors Board A
• The picture shows the factory setting of the jumpers.
• To change the polarity of the second output (Output 2) the position of JP6/JP9 has to be changed.
• To disconnect the unit from the gate signal on the bus JP11/JP10 has to be removed.
• To change the direction of the time control voltage CVT (i.e. if an increasing CV increases or decreases the
time parameters) the position of JP7/JP4 has to be changed
• If a parameter (A, D, R) should be removed from the CVT control the jumper in question has to be removed
• Normally Systain is not affected by CVT (as it's not a time parameter) and the corresponding jumper is not
installed in the factory. If voltage control of Sustain is desired the corresponding jumper has to be installed
on the position "S" of JP8/JP5.
JP11/JP10:
Bus Gate
JP9/JP6: Polarity of Output 2
upper position = inverted
lower position = non-inverted
JP7/JP4: Time CV Polarity
upper position = inverted
lower position = non-inverted
JP8/JP5: Time CV assignment
when jumper installed the corresponding
parameter (A, D, S, R) is CV controlled
JP1:
Bus Connecto
r
ADSR #2 ADSR #1
A-140-2 Dual ADSR
Position and function of the jumper Board B
JP14 is an horizontal (lying) jumper and is located on the lower board. To remove or install this jumper a
suitable tool has to be used (e.g. a small plier) because it's between the two boards. One may also remove the
upper from the lower pc board for easier access. For this the mounting screw at the top of the board has to be
removed and the upper board removed from the lower board by pulling out the two 10-pin connectors.
Pay attention to correct alignment of the two small 10-pin connectors that are used to connect the two boards
when the upper board is re-installed. Otherwise the module will be damaged ! Such a damage cannot be
treated as a warranty case !
JP14: Gate normalling
Gate In 1 Gate In 2 Æ

Produkt Specifikationer

Mærke: Doepfer
Kategori: Ikke kategoriseret
Model: A-140-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Doepfer A-140-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Doepfer Manualer

Doepfer

Doepfer A-100 Manual

1 September 2024
Doepfer

Doepfer Dark Link Manual

21 August 2024
Doepfer

Doepfer A-196 Manual

20 August 2024
Doepfer

Doepfer A-134 Manual

20 August 2024
Doepfer

Doepfer A-135-2v Manual

19 August 2024
Doepfer

Doepfer A-145 Manual

19 August 2024
Doepfer

Doepfer A-101-2 Manual

19 August 2024
Doepfer

Doepfer A-99 Manual

19 August 2024
Doepfer

Doepfer A-103 Manual

19 August 2024
Doepfer

Doepfer A-165 Manual

18 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hughes & Kettner

Hughes & Kettner Triplex Manual

16 September 2025
Defender

Defender NS-503 Manual

16 September 2025
Hama

Hama WKM-500 Manual

16 September 2025
Kela

Kela Saltus 22972 Manual

16 September 2025
Turbo Air

Turbo Air PRO-26H2 Manual

16 September 2025
Gumotex

Gumotex Baraka Manual

16 September 2025
Quick Dam

Quick Dam Flood Gate QDFG35 Manual

16 September 2025
Yard Force

Yard Force YF5515LT Manual

16 September 2025
Milwaukee

Milwaukee 4932479730 Manual

16 September 2025
Texican

Texican Chip Master CD-45 Manual

16 September 2025