Dormakaba 8000 Manual

Dormakaba Ikke kategoriseret 8000

Læs gratis den danske manual til Dormakaba 8000 (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 112 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 56.5 anmeldelser. Har du et spørgsmål om Dormakaba 8000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

ES 100 Power Supply

24 Volt D.C. Power Supply

General:

The ES 100 Power Supply is a general purpose power supply providing 24 volt,

full wave filtered DC power at a continuous current rating of 1.3 amps.

Zones:

The ES 100 contains as a standard feature two (2) zone capability. Each zone has

one (1) set of control input terminals and one (1) set of output terminals. The 1.3

amp output rating is applied to either zone as long as the continuous current draw

does not exceed 1.3 amps (Example zone #1 may draw 1.0 amps however zone #2

may not exceed 0.3amps. If zone #2 is not used then zone #1 is rated at 1.3 amps

continuously. The control input may be used as either a dry contact or voltage

input.

Operation:

Trigger input of the ES 100 Power supply will occur by a switch and/or relay. A

Dry Contact input refers to a switch or relay contact that provides no external

voltage to activate the Power Supply. Contacts can be either normally open

contacts or normally closed contacts. These input contacts are connected to

terminals #3 & #4 for zone #1 and terminals #7 & #8 for zone #2. Normally Open

Contacts are use when the ES 8000 Series Exit Device is used in conjunction with

this Power Supply. Normally Close Contacts are used when the DE9000 Delayed

Egress Exit Device is used in conjunction with this Power Supply. A fire alarm

system can be used as the normally open or normally closed contact to trigger the

ES 8000 Series Exit Device or give constant power to the DE9000 Series Delayed

Egress Exit Device. DORMA recommends using the normally closed contacts of

the building’s fire alarm system to control the power being supplied to the

DE9000 Delayed Egress Exit Device from the ES100 Power Supply.

Voltage input refers to an external source of 24 VDC power required to activate

the output terminals. To use zone #1 as a Voltage Input, connect the control

voltage positive (+) wire to terminal #3 and the voltage negative (-) wire to

terminal #2. The external source voltage must have a current rating of 0.045 amps

per zone. Connect the output device such as ES8000 Series Exit Device with

Electric Latch Retraction and DE9000 Series Delayed Egress Exit Device to

terminals #1 and #2. When control voltage is present it will power the output

terminals. To use zone #2 as a Voltage Input, connect the control voltage positive

(+) wire to terminal #7 and the voltage negative (-) wire to terminal #6. The

external source voltage must have a current rating of 0.045 amps per zone.

Connect the output device such as ES8000 Series Exit Device with Electric Latch

Retraction and DE9000 Series Delayed Egress Exit Device to terminals #5 and

#6. When control voltage is present it will power the output terminals.

Circuit Protection:

The ES100 Power Supply is protected agai and overloads by a nst short circuits

0.75 amp slow blowing, field replaceable, fuse in the 120 VAC power line. In

addition a 3.0 amp circuit breaker is provided in the 24 VDC power supply

section to protect both zone #1 and zone #2. Each zone can supply 6.0 amps for

0.5 seconds. This design provides the high inrush currents required for the circuits

of the ES 8000 Electric Latch Retraction Exit Device.

Mechanical and Size Specifications:

Enclosure:

8” Enclosure Height

8” Enclosure Width

4” Enclosure Depth

Electrical Knockouts:

Quantity (2) ½” Diameter (per side)

Quantity (1) ¾” Diameter (per side)

Cover:

Hinged cover with finger pull and locking screw

Rating:

NEMA 1 Enclosure for inside use.

Electrical Specification:

Input Voltage: Input Circuit Protection:

120 VAC, +10% -15% 0.75 AMP slow blow

Input Current:

0.75 AMP Maximum

Output Voltage: Output Circuit Protection:

24 VDC 3.0 Amp Push to reset

Circuit Breaker

Continuous Output Current:

1.3 AMPS total (zone 1 and zone combined)

Surge Output Current: Quantity of Zones:

6.0 AMPS per zone Two (2)

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	8000

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba 8000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tascam MP-800U Manual

30 September 2025

Baninni Sacco Prestigio BN180 Manual

30 September 2025

Joy-It SBC-MD-TB6600 Manual

30 September 2025

Mount-It! MI-791 Manual

30 September 2025

EasyMaxx 15666 Manual

30 September 2025

Decimator DMON-12S Manual

29 September 2025

Anker 310 USB-C to HDMI Adapter Manual

29 September 2025

Philco PHHM 6301 Manual

29 September 2025

Autoscript EVO-IP19 Manual

29 September 2025

MBM BR772P Manual

29 September 2025