Dormakaba Auditcon 552 Manual

Dormakaba Ikke kategoriseret Auditcon 552

Læs gratis den danske manual til Dormakaba Auditcon 552 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Dormakaba Auditcon 552, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

(P/N) 3047.025 Rev D

Page 1 of 4

INSTALLATION INSTRUCTIONS

Prepare for New Installation of the Lock (If Required)

1. Use the installation template provided to establish the exact

locations (relative to the spindle hole) of the mounting holes

for the dial assembly and the lock assembly.

2. The spindle hole diameter can be a minimum of .406”

(10.3mm) to a maximum of .438” (11.1mm). The .406”

(10.3mm) diameter is recommended. Spindle hole must be

deburred.

3. The dial assembly mounting screws require drilled and

tapped holes to 3/8” (9.5mm) depth if possible (minimum

1/4” or 6.4mm depth required.) Drill either the two horizontal

mounting holes or the two vertical holes.

4. When mounting the lock unit (i.e., integrating it in a

boltwork), make sure that the lock bolt has clearance to

freely move to its end positions and that the shifting force

works only in the axial direction (direction of movement).

Lateral forces should not be exerted on the lock.

5. If other parts of the boltwork are to be connected to the lock

unit (e.g., for activating a blocking device), corresponding

adapters can be fixed with screws (#10-32 or M4) to the

front of the lock bolt (tightening torque for 15mm screwing

depth: 200Ncm maximum).

Part I: Install Lock Case Assembly

WARNING: Do not take the lock case assembly apart. There are

no field servicable parts inside lock case. This action will void the

warranty.

1. Insert a cable shield into the deburred spindle hole from the

back side of the container door.

2. Place the protective tube over the tube retainer on the lock

case. (Figure 2)

3. While holding the lock case assembly, guide the tube through

the spindle hole and place the lock case flush against the

inside of the container door.

The installation instructions are the basis for Security Agency

Approvals. The lock installation must be done in accordance

to these instructions in order to maintain the labeled

approval level.

Design Parameters for Auditcon 2 Series Locks

1. Bolt dimensions (nominal): .312 inches x 1.000 inches/

8 x 25.4mm

2. Bolt movement (nominal): .465 inches/11.8mm

3. Bolt extension: .465 inches/11.8 mm

4. Maximum load movable by the bolt: 5 lbs. (22N)

NOTE: Auditcon 2 dead bolt locks may not open if more than

5 lbs. (22N) of force is applied to the end or side of the bolt.

5. Maximum load against bolt when thrown (all directions):

224.8 lbs. (1kN)

6. The lock can be fitted to safes or vault doors of any

material.

NOTE: As is the case with all mechanical and electronic

locking devices, the container and boltworks must be

designed to protect the lock.

AUDITCON® 2 SERIES LOCKS

MODELS 52, T52, 252, 552  ROUND HOUSING DEAD BOLT

Basic Tools and Materials Needed

• Medium Phillips head screwdriver (#2) (recommend

magnetized tip)

• 9/64” Allen Wrench

• Fine pitch hacksaw (32 teeth/inch)

• Small flat file

• All-purpose scissors

• Tape measure or ruler

• ESD wrist band

Recommended, but not required:

• Torque screwdriver (30 inch-pounds/3.4 newton-meters

capacity)

• Small vise grip

• Loctite® 262 (Red) for use on lock case mounting screws

WARNING: dormakaba locks are protected from 25,000

V Electrostatic Discharge (ESD) damage when correctly

installed. Follow these precautions to avoid ESD damage

when installing the lock:

• Handle the keypad assembly by the outer edge only.

• Use an ESD wrist band grounded to the lock or container

during installation.

Figure 2

Figure 1 - Dead Bolt Lock Parts

Figure 3

Dial Assembly

Keypad

Assembly

with Decal

Spindle

& Tube

Lock Case

Assembly

Lock Case

Mounting

Screws (4)

Spindle

Mounting

Screw

Cable

Dial

Assembly

Mounting

Screws (2) Cable Shields (2)

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	Auditcon 552

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba Auditcon 552 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba CenTran 4 Manual

19 Oktober 2025

Dormakaba Crane S1 Manual

19 Oktober 2025

Dormakaba Auditcon T52 Manual

18 Oktober 2025

Dormakaba 12C Manual

18 Oktober 2025

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JET TPFA-Z Manual

15 December 2025

Crosley Asheville CF1149 Manual

15 December 2025

Mercusys MC200 Manual

15 December 2025

Growatt ARK 2.5L-A1 Manual

15 December 2025

ALNO MC40244 Manual

15 December 2025

BEKO BG640EXVIXL Manual

15 December 2025

Milwaukee 48-22-9200 Manual

15 December 2025

Growatt ALP 5.0L-E1-AU Manual

15 December 2025

Arçelik A55 A 950 A Manual

15 December 2025

Extron EBP 106 Manual

15 December 2025