Dormakaba C500 Manual

Dormakaba Ikke kategoriseret C500

Læs gratis den danske manual til Dormakaba C500 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Dormakaba C500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

C500 CYLINDRICAL LEVERSET

—

Installation Instructions

76011629 05/15www.dorma.com

1. Install latch

1.1 Place the latch into the door edge.

Orient such that the beveled edge of the latch

faces the door jamb.

1.2 Secure with two 8-32 x ¾ ” combo screws.

NOTE: Latch ﬁ ller to be used for doors with

1-1/8” face plate prep and 1” latch bore.

3. Install mounting plate & spring cage

3.1 Hold the lock assembly in

place.

3.2 Place the mounting plate

against the door and

secure with two

10-32 x 1-½ ” screws.

3.3 Place the spring cage

assembly onto the

mounting plate and

secure to the door using

two 10-32 x 1-½ ” screws.

NOTE: If installing a non-thru-

bolt chassis, secure the spring

cage using two M5-0.5x⅜ ”

screws.

Overall Exploded View

4. Install rose & inside lever

4.1 Push the inside rose

onto the spring cage

oriented such that the

rose dimples are on the

sides.

NOTE: Be sure the

lever insert is inserted

into the inside lever

prior to installation.

4.2 Push the inside

lever onto the

spindle until it

clicks into place.

Beveled

edge

sides.

Inside

lever

Inside

rose

Spring

cage

Rose dimple

locations

5. Install strike

5.1 Insert strike as shown, and secure with two

12-24 x ¾ ” combo screws.

Strike part list

1 - 12-24 x ¾ ” combo-screws

2 - Strike plate

8 - Latch sleeve

9 - Latch ﬁ ller plate

10 - Latch

11 - 8-32 x ¾ ” combo

screws (x2)

12 - Mounting plate

13 - 10-32 x 1-½ ” screws (x2)

14 - Spring cage

Part List

1 - IC core

2 - Outside IC lever

3 - Outside

conventional

cylinder lever

4 - Conventional

cylinder

5 - Thru-bolt studs

6 - Outside rose

assembly

7 - Lock assembly

screws

Spring

cage

10-32 x 1-½ ”

screws

2. Install lock assembly

Adjust for door thickness

NOTE: Lock comes adjusted

for 1-¾ ” door from the factory.

2.1 To adjust the lock

assembly for door

thickness, align the

center of the chassis

with the center of the

latch.

2.2 Remove the outside lever

and separate the outside rose

assembly from the

adjustment plate.

2.3 Rotate the adjustment plate

to adjust for proper

door thickness.

2.4 Realign & install the outside

rose assembly. Replace the

outside lever.

(See supplementary

sections II & III.)

2.5 Slide the lock assembly into the face of

the door.

Be sure to engage the inner latch

mechanism of the chassis with the

Chassis

tch

mechanism

the

chassis

with

the

sho

wn.

Center of

latch

Chassis

Outside rose

assembly

Lat

Outside

lever

Outside rose

assembly

Adjustment

plate

ools required for installatio

oss

riv

Flathead screwdr

ver

109

15 - 10-32 x 1-½ ”

screws (x2)

16 - Inside rose

17 - Lever insert

18 - Inside lever

19 - M5-0.5 x ⅜ ”

screws

Non-thru-bolt installation

Dimple

109

Thru-bolt installation (preferred)

Mounting

pla

Slo

t i

cha

ssi

M5-0.5 x ⅜ ”

screws

Thru-bolt

chassis

Non-thru-bolt

chassis

Supplementary Instructions

76011629 05/15 www.dorma.com

Removal

1. Remove the outside lever by inserting

the key, turn clockwise and at 90°. hold

Using the pick, depress the lever catch

through the pick hole and remove the

lever. Remove the key. (Figure 1a & 1b)

2. Remove the lever insert and cylinder.

(Figure 2)

Reinstallation

3. Replace with new cylinder and reinstall

the lever insert. (Figure 2)

Be sure the tailpiece is horizontal.

4. Press the outside lever onto the

spindle until it contacts the lever catch.

(Figure 3)

5. Insert the key into the cylinder, turn

clockwise and hold at 90°. Press the

lever fully onto the spindle until

it clicks into place. Release the

key. (Figure 3)

III. Removing & reassembling interchangeable core lever

IV. Removing & reassembling standard cylinder lever (cylinder changes)

Removal

1. Insert the control key into the IC core,

rotate the key 15° clockwise, and remove

the core and tail piece from the lever.

2. Using a ﬂ athead screwdriver, retract the

lever catch inside the spindle and remove

the lever.

Reinstallation

NOTE: REMOVE the spring from the

IC cylinder tailpiece for 7 pin cores

ONLY.

3. Press the lever onto the spindle until it

snaps into place.

4. Install the tail piece on the core.

Insert the control key into the core,

rotate the key 15° clockwise, push the

core fully into the lever and turn counter

clockwise 15 ° (home position), and

remove the key.

V. C501 Dummy trim installation

1. Remove the temporary screw from

the back of the dummy spring cage and

separate the lever.

2. Separate the rose and the dummy

spring cage.

3. Secure the dummy spring cage to the

door using the two combo screws.

4. Press the rose onto the dummy spring

cage and rotate to lock the rose in

place.

NOTE: Be sure the rose notches

are properly in line with the spring

cage notches.

5. Install the washer (beveled side out)

onto the 1/4-20x2-1/2” screw

and secure the lever through the

opposite side of the door.

IC core

with

tailpiece

IC core lever

IC core

IC core lever

Lever catch

90°

Figure 1a

Figure 1b

Figure 2

Figure 3

Pick hole

Pick

Cylinder

Lever

insert

Tailpiece

(horizontal)

Lever

catch

IC cylinder

tailpiece

II. C580 - Storeroom function

NOTE: Storeroom function has a pushbutton on the inside spindle. A closed lever is

used for the inside to hold the button in a locked position.

Temporary

screw at back of

dummy spring

cage

Washer

Rose

Dummy

spring

cage

1/4-20x2-½ ”

screw

Lever

Spring cage

notches

Rose

notches

Pushbutton

Inside

spindle

Closed inside

lever

I. C570 - Classroom function

TIMING INSTRUCTIONS: Install lock on door. Remove outside lever and cylinder (for

Interchangeable Core locks, leave lever in place and remove core and tail piece)

OUTSIDE OF DOOR:

Rotate key spindle fully counter-clockwise. Install cylinder and lever.

(See steps 4 & 5 in section IV.)

Key

spindle

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	C500

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba C500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite TLM406NC Manual

31 Juli 2025

Tripp Lite Protect It! TLP76RBTEL Manual

31 Juli 2025

Tripp Lite N286-40G-ESR4-J Manual

31 Juli 2025

Emos H5011 Manual

31 Juli 2025

Emos ZM6145 Manual

31 Juli 2025

Oppo Find X7 Manual

31 Juli 2025

Intellinet 713191 Manual

31 Juli 2025

Emos DCFW01 Manual

31 Juli 2025

AIC RSC-3ET Manual

31 Juli 2025

Tone City King Of Blues Overdrive Manual

31 Juli 2025