Dormakaba EMLTP Manual

Dormakaba Ikke kategoriseret EMLTP

Læs gratis den danske manual til Dormakaba EMLTP (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Dormakaba EMLTP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

INSTALLATION

EML310TP, EML320TP

Electromagnetic Locks

DORMA DRIVE, DRAWER AC, REAMSTOWN, PA 17567 PHONE: (800) 523-8483 (717) 336-3881 FAX: (717) 336-2106

EMAIL: archdw.us@dormakaba.com WEBSITE: dormakaba.us

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available

with this product, a survey and assessment of the

physical area in which the product will be installed must

be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be

strong enough to meet or exceed the holding force of the

product.

4. The product must be protected from potential damage

due to intruders or tampering.

5. The product should be installed in a location that will not

hinder or create a potential safety hazard to authorized

personnel accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must

make a determination of the optimal mounting method for

this specific application.

7. The components, hardware, installation instructions and

mounting template included with this product are intended

for use on outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories must be used in the following

applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that don’t have a door frame

• Hollow metal or wood frames where the door

stop is not thick enough to allow the product to

be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to be

mounted low enough to meet the magnet surface

Refer to the page 5 & 6 Product Accessories Guide for

further information. Accessories may impact holding

force.

11. Installation of this product should be done by an

experienced installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound

be applied to all screws during installation to reduce chance of

screws loosening over extended time.

ISEML310TP

08281550

PCN18040

R08-19GR

1. Mount the electromagnetic lock to the door frame as outlined

on the installation template included with the product.

NOTE: During installation of the armature plate to the door it

is essential that the armature plate remains movable. The

armature plate must be allowed to pivot on the center-mounting

bolt to allow proper alignment with the magnet surface. If the

plate is not aligned with the magnet surface, the lock may lose

holding force or not lock at all.

The head of the armature mounting bolt ships with a rubber

washer affixed to it. This washer should project slightly beyond

the surface of the armature plate. This is to allow the washer

to expand when power is removed and break the air vacuum

between the plate and the magnet surface. If this washer is

removed or trimmed the lock will appear to have some holding

force even when power is removed.

For added safety, thread locking compound has been provided

for the armature plate bolt and the four captive electromagnetic

lock mounting screws.

WARNING: Improper installation, maintenance, inspection

or usage of the product or any related accessories or parts

may cause the electromagnetic lock, armature plate and

associated hardware to disengage and fall, causing serious

bodily injury and property damage. dormakaba Canada Inc.

and/or dormakaba USA Inc. will not be liable to the installer,

purchaser, end user or anyone else for damage or injury

to person or property due to improper installation, care,

storage, handling, maintenance, inspection, abuse, misuse

or act of God or nature involving this product or any related

accessories or parts.

2. Route the power supply connecting wire through the door

frame and into the wire access hole in the top of the magnet

housing. Connecting wire should be of sufficient gauge for

the lock being installed and the distance being run.

Installation Instructions

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

3. Set the DC voltage jumpers on JP1 as follows.

For 12V operation two jumpers are used; One on the

two upper pins and the other on the two lower ones.

For 24V operation only one jumper is used to connect

the two center pins (factory setting)

Connect the positive (+) lead from the power supply to

TB1-1. Connect the negative (-) lead from the power

supply to TB1-2. For wiring installations, refer to

figure 1.

4. Delayed Relock Feature - The delayed relock feature can

be used to momentarily release the lock and keep it

unlocked for a time period from 0 to 90 seconds. The

time delay for this feature can be adjusted by carefully

turning the potentiometer in a counterclockwise

direction to increase delay time. Factory setting is zero

seconds (fully clockwise).

NOTE: On the EML320TP double-door model turn both

potentiometers counterclockwise to increase the relock

delay.

JP1

JP2

TB1

Alarm Time Setting

Voltage Selection

Light Emitting

Diode (LED)

Time Delay Setting (0-90 secs)

CCW increases time delay

N.C

N.O.

Common

N.C

N.O.

Common

-Common (Ground)

+12/24VDC input

Bond Alert Sensor*

Output contacts SPDT rated at

2.0A @ 30VDC max

Magnet power from

Power Supply

Alarm Status*

Output contacts SPDT rated

2.0A @ 30VDC max.

Power Input Requirements

MODEL 12VDC 24VDC

EML310TP 0.59A 0.29A

EML320TP 1.18A 0.58A

*Shown with Door Open/unlocked

Fig. 1 – Wiring Schematic

Electromagnetic locks must conform to local fire codes, National Building Codes and Life Safety Codes. See your

Local Authority Having Jurisdiction for specific code requirements.

Alarm

Alarm Status Remote Indication - When the door is closed

and an illegal armature plate is detected, the common

contact (TB1-6) and the normally open contact (TB1-7)

are activated for the preset period of time. The alarm

status relay contacts are rated at 30VDC @ 2.0 amps

maximum.

Alarm Time Setting

- Refer to figure 1 (JP2). Note 15 or

30 seconds requires one jumper; 60 seconds requires

no jumper and indefinitely requires two jumpers. Unused

jumpers can be stored on a single pin.

15 Seconds 30 Seconds 60 Seconds Indefinitely

Bond Alert (BA)

Magnet Locked - When the magnet is locked, the common

contact (TB1-3) and the normally open contact (TB1-4)

are closed. The normally closed contact (TB1-5) would be

open.

Magnet Unlocked - When the magnet is unlocked, the

common contact (TB1-3) and the normally closed contact

(TB1-5) are closed. The BA relay contacts are rated 30VDC

@ 2.0 amps maximum.

This feature can detect the quality of the locking bond

between the surface of the magnet and the armature plate.

The sensitivity of this feature is such that a foreign object

with a thickness of .007” (.18mm) is sufficient to allow the

sensor to detect a problem.

Due to the sensitivity of this feature and the necessity to

maintain a reliable locking bond, these surfaces must be

kept free of contaminating materials. Both the lock surface

and the armature plate must be cleaned periodically with

a non-abrasive cleanser. Alignment of armature plate and

magnet is required to ensure proper function of sensor.

LED Local Indication (Light Emitting Diode)

Red LED on solid – Maglock is unlocked

Green LED on solid – Maglock is locked.

Red LED blinking quickly – Illegal armature plate used;

alarm will be activated.

Each individually encoded armature plate is registered to

match it’s own electromagnetic lock.

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	EMLTP

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba EMLTP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Dormakaba DKX Type IV Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ORNO OR-PSU-1675 Manual

15 Juni 2025

EmberGlo ES5CTS Manual

15 Juni 2025

Chapin 8201A Manual

15 Juni 2025

Gourmia GDK2365 Manual

15 Juni 2025

Xiaomi Wireless Mouse 3 Manual

15 Juni 2025

Auray SVRK-12U-D Manual

15 Juni 2025

Aiphone IXGW-TGW Manual

15 Juni 2025

Aiphone AC-2DE Manual

15 Juni 2025

Schlage S280 Manual

15 Juni 2025

Cleveland PGM3002 Manual

15 Juni 2025