Dormakaba ES100 Manual

Dormakaba Ikke kategoriseret ES100

Læs gratis den danske manual til Dormakaba ES100 (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Dormakaba ES100, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
ES 100 Power Supply
24 Volt D.C. Power Supply
General:
The ES 100 Power Supply is a general purpose power supply providing 24 volt,
full wave filtered DC power at a continuous current rating of 1.3 amps.
Zones:
The ES 100 contains as a standard feature two (2) zone capability. Each zone has
one (1) set of control input terminals and one (1) set of output terminals. The 1.3
amp output rating is applied to either zone as long as the continuous current draw
does not exceed 1.3 amps (Example zone #1 may draw 1.0 amps however zone #2
may not exceed 0.3amps. If zone #2 is not used then zone #1 is rated at 1.3 amps
continuously. The control input may be used as either a dry contact or voltage
input.
Operation:
Trigger input of the ES 100 Power supply will occur by a switch and/or relay. A
Dry Contact input refers to a switch or relay contact that provides no external
voltage to activate the Power Supply. Contacts can be either normally open
contacts or normally closed contacts. These input contacts are connected to
terminals #3 & #4 for zone #1 and terminals #7 & #8 for zone #2. Normally Open
Contacts are use when the ES 8000 Series Exit Device is used in conjunction with
this Power Supply. Normally Close Contacts are used when the DE9000 Delayed
Egress Exit Device is used in conjunction with this Power Supply. A fire alarm
system can be used as the normally open or normally closed contact to trigger the
ES 8000 Series Exit Device or give constant power to the DE9000 Series Delayed
Egress Exit Device. DORMA recommends using the normally closed contacts of
the building’s fire alarm system to control the power being supplied to the
DE9000 Delayed Egress Exit Device from the ES100 Power Supply.
Voltage input refers to an external source of 24 VDC power required to activate
the output terminals. To use zone #1 as a Voltage Input, connect the control
voltage positive (+) wire to terminal #3 and the voltage negative (-) wire to
terminal #2. The external source voltage must have a current rating of 0.045 amps
per zone. Connect the output device such as ES8000 Series Exit Device with
Electric Latch Retraction and DE9000 Series Delayed Egress Exit Device to
terminals #1 and #2. When control voltage is present it will power the output
terminals. To use zone #2 as a Voltage Input, connect the control voltage positive
(+) wire to terminal #7 and the voltage negative (-) wire to terminal #6. The
external source voltage must have a current rating of 0.045 amps per zone.
Connect the output device such as ES8000 Series Exit Device with Electric Latch
Retraction and DE9000 Series Delayed Egress Exit Device to terminals #5 and
#6. When control voltage is present it will power the output terminals.
Circuit Protection:
The ES100 Power Supply is protected agai and overloads by a nst short circuits
0.75 amp slow blowing, field replaceable, fuse in the 120 VAC power line. In
addition a 3.0 amp circuit breaker is provided in the 24 VDC power supply
section to protect both zone #1 and zone #2. Each zone can supply 6.0 amps for
0.5 seconds. This design provides the high inrush currents required for the circuits
of the ES 8000 Electric Latch Retraction Exit Device.
Mechanical and Size Specifications:
Enclosure:
8” Enclosure Height
8” Enclosure Width
4” Enclosure Depth
Electrical Knockouts:
Quantity (2) ½” Diameter (per side)
Quantity (1) ¾” Diameter (per side)
Cover:
Hinged cover with finger pull and locking screw
Rating:
NEMA 1 Enclosure for inside use.
Electrical Specification:
Input Voltage: Input Circuit Protection:
120 VAC, +10% -15% 0.75 AMP slow blow
Input Current:
0.75 AMP Maximum
Output Voltage: Output Circuit Protection:
24 VDC 3.0 Amp Push to reset
Circuit Breaker
Continuous Output Current:
1.3 AMPS total (zone 1 and zone combined)
Surge Output Current: Quantity of Zones:
6.0 AMPS per zone Two (2)

Produkt Specifikationer

Mærke: Dormakaba
Kategori: Ikke kategoriseret
Model: ES100

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba ES100 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Dormakaba Manualer

Dormakaba

Dormakaba 3513-DM Manual

29 Juni 2025
Dormakaba

Dormakaba Keyscan EC1500 Manual

21 August 2024
Dormakaba

Dormakaba RCI S2500A Manual

21 August 2024
Dormakaba

Dormakaba EAC Manual

21 August 2024
Dormakaba

Dormakaba CLM9000 Manual

21 August 2024
Dormakaba

Dormakaba DKX Type III Manual

21 August 2024
Dormakaba

Dormakaba 9800 Manual

21 August 2024
Dormakaba

Dormakaba HSW-GP Manual

21 August 2024
Dormakaba

Dormakaba DKX-10 Manual

21 August 2024
Dormakaba

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Growatt

Growatt MID 33-50KTL3-X2 Manual

22 August 2025
Hoymiles

Hoymiles HYS-3.0LV-EUG1 Manual

22 August 2025
Advantech

Advantech WISE-3310 Manual

22 August 2025
Advantech

Advantech ADAM-3014 Manual

22 August 2025
AXESS

AXESS AXDSPX-HN3 Manual

22 August 2025
Growatt

Growatt MOD 3-15KTL3-X Manual

22 August 2025
AXESS

AXESS AXI-RGB3 Manual

22 August 2025
Advantech

Advantech DS-980 Manual

22 August 2025
Korona

Korona Warmhalteplatte Manual

22 August 2025
Simrad

Simrad SD10 Manual

22 August 2025