Dormakaba ES62 Manual

Dormakaba Ikke kategoriseret ES62

Læs gratis den danske manual til Dormakaba ES62 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Dormakaba ES62, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION

ES62 - DOOR PAIR HOUSING

ELECTRIC STRIKES

ISES62DPH

08281190

PCN18035

R01-19TG

DORMA DRIVE, DRAWER AC, REAMSTOWN, PA 17567 PHONE: (800) 523-8483 (717) 336-3881 FAX: (717) 336-2106

EMAIL: archdw.us@dormakaba.com dormakaba.us WEBSITE:

Instructions

1. Mark horizontal center line (CL) of existing device latch from active door to inactive door. Align center of Door Pair Housing

(DPH) with horizontal centerline marked on inactive door and square it with edge of the inactive door. Maintain 3/16”

minimum gap between the exit device & strike face for proper functioning of exit device. See ISES62 for details.

2. Mark the mounting holes for the DPH on the inactive door using DPH as template.

3. Drill two 13/32” (10.5mm) holes through inactive door).

4. Mount DPH to inactive door using hardware as shown.

Note: Wire access hole is not provided, drill DPH as required.

5. Make wire connections from the power source to the appropriate wire harness supplied. Use the 12V harness for 12VDC,

12-24VAC or 11-16VAC. Use the 24V harness only for 24VDC.

6. Mount the electric strike with 1/4-20 UNC (Hole C) screws provided in the outer oval mounting holes (the

outer slots). Adjust electric strike horizontally until exit device latch fully engages with the door closed.

Note: Ensure a 1/16” [1.5mm] clearance between exit device latch and the electric strike keeper is maintained.

7. Tighten the two mounting screws and check operation. Adjust the horizontal position of electric strike as required.

8. Using the electric strike as a marking template, drill & tap for 1/4-20 UNC (Hole D). Using the 1/4-20 UNC screws provided

secure the electric strike through the locking holes.

Note: ES62 strike is not adjustable after installing these screws.

IMPORTANT: The fire and/or security ratings shown on the ES62(F) strike labels no longer apply with the use of the Door Pair

Housing.

ES62 Typical Door Pair

Housing Assembly

INACTIVE

DOOR

SEX NUT 1/4-20

WITH 13/32" HOLE

THROUGH (DOOR)

(2 PLACES)

HOLE C

1/4-20 X 1"

ADJUSTMENT

SCREW

HOLE C

1/4-20 X 1"

SCREW

HOLE D

1/4-20 X 1"

LOCKDOWN

SCREW

(2 PLACES)

3-3/4” (95mm)

7/8” (22.2mm)

1/4-20 X 2.5"

(2 PLACES)

ES62 DOOR

PAIR HOUSING

INSTALLATION

ISES61DPH

08281170

PCN18035

R01-19TG

DORMA DRIVE, DRAWER AC, REAMSTOWN, PA 17567 PHONE: (800) 523-8483 (717) 336-3881 FAX: (717) 336-2106

EMAIL: archdw.us@dormakaba.com dormakaba.us WEBSITE:

Instructions

1. Mark center line (CL) of existing device latch from active door to inactive door. Align center of Door Pair Housing (DPH) with

horizontal centerline marked on inactive door and square it with edge of the inactive door. Maintain 3/16 minimum gap between "

the exit device & strike face for proper functioning of exit device. See ISES61 for details.

2. Mark the mounting holes for the Door Pair Housing (DPH) on the inactive door using DPH as template.

3. Drill two 13/32 (10.5mm) holes through inactive door."

4. Drill wire access hole into desired area of DPH. Pull two (2) wires through the access hole and connect to strike

(polarity is not critical).

5. Temporarily mount ES61 strike to DPH through the slotted holes (Hole C) using 1/4-20 UNC x 1 screws provided."

6. Mount DPH to inactive door using the two (2) 1/4-20 x 3” screws and 1/4-20 Sex Nuts supplied.

7. Adjust electric strike insert horizontally, if necessary, until Pullman Latch engages when door is closed. (See Fig. 3 on ES61

installation instructions if further horizontal insert adjustment is necessary).

8. Mark, drill and tap Hole D for 1/4-20 x 1” provided to secure the final location.

IMPORTANT: The security ratings shown on the ES61 strike labels no longer apply with the use of the Door Pair Housing.

INACTIVE

DOOR

ES61 DOOR

PAIR HOUSING

SCREW

1/4-20 x 3”

DRILL

13/32” HOLE

(2 PLACES)

ACTIVE

DOOR

EDGE

TYPICAL SURFACE

EXIT DEVICE

SEX NUT

1/4-20

HOLE C

ADJUSTMENT

SCREW

1/4-20 x 1”

HOLE D

LOCKDOWN

SCREW

1/4-20x1”

HOLE D

LOCKDOWN

SCREW

1/4-20 1” x

HOLE C

ADJUSTMENT

SCREW

1/4-20 1” x

ES61 Typical Door Pair

Housing Assembly

ES61 - DOOR PAIR HOUSING

ELECTRIC STRIKES

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	ES62

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba ES62 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Dormakaba DKX Type IV Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox Airvox SW695 Manual

15 Juni 2025

Stiga SBC 635 KD Manual

15 Juni 2025

Cleveland 36CGM300 Manual

15 Juni 2025

Gourmia GTF7970 Manual

15 Juni 2025

Planet Audio P9630B Manual

15 Juni 2025

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025

Lavex 842CD12VST12 Manual

15 Juni 2025

Marshall RCP-PLUS Manual

15 Juni 2025

Hughes & Kettner BassForce XL Manual

15 Juni 2025

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025