Dormakaba ES96 Manual

Dormakaba Ikke kategoriseret ES96

Læs gratis den danske manual til Dormakaba ES96 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Dormakaba ES96, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

ISES96F

08281280

PCN2007

R09-20GR

I N S TA L L AT I O N S

E S 9 6 F

Electric Strikes

DORMA DRIVE, DRAWER AC, REAMSTOWN, PA 17567 PHONE: (800) 523-8483 (717) 336-3881 FAX: (717) 336-2106

EMAIL: archdw.us@dormakaba.com dormakaba.us WEBSITE:

Standard Parts:

Insert

Deadbolt Keeper

Deadbolt Plug

Deadlatch Ramp (Auxiliary Bolt Bracket)

Keeper Sliding Shims: 1/16" (1.5mm) and 1/8" (3.0mm)

A Centerline Latch Faceplate and an Offset Latch Faceplate are

provided. Both are: 4-7/8" x 1-1/4" (123.8mm x 31.8mm)

Trim Plate

12VDC or 12 to 24VAC Cable Connector

24VDC Cable Connector

Anti-Tamper Security Screws (2x 12-24) and Bit

Mounting Tab Kit (2x tabs, 4x shims and 5x 12-24 screws)

Inductive Kickback Suppressor - MOV

Red Black

24VDC

Terminal

12VDC

12-24VAC

Terminal

Latch

Monitor

Optional LM

Wiring the ES96F Series Electric Strike

Wiring Instructions

Use the appropriate wire harness supplied.

12V for 12VDC & 12-24VAC*

24V for 24VDC only

Attach the red wire to (+) positive of the power supply.

Attach the black wire to the (–) negative of the power supply.

If using AC power, polarity is not observed.

To meet BHMA A156.31, install the MOV provided across the positive

and negative wires or terminals of the harness. The MOV is not polarity

sensitive.

NOTE: If a suppression diode is required for access control,

observe proper polarity.

Latch Monitor Wires

Black = Common (C)

Blue = Normally Closed (NC)

Orange = Normally Open (NO)

The ES96F fail secure locking mechanism shall only be installed where allowed by the local authority having jurisdiction and shall not

impair the operation of the panic hardware or intended operation of the emergency exit.

Model ES96F must be connected to a compatible UL Listed Burglary or Access Control Power Supply.

Accessories:

96LM Latch Monitor : 08116660

UL 294 Performance Ratings:

Access Control Line Security : Level I

Destructive Attack : Level I

Endurance : Level IV

Standby Power : Level I

Trim Plate: This can be used in

case the frame cutout is bigger

than required.

Bend tabs to

grip frame

Deadbolt Plug: If the lock set

doesn’t have a deadbolt, then

replace deadbolt keeper with

deadbolt plug.

NOTE: Deadlatch Ramp also acts

as a Keeper stop, so don’t forget to

insert it for centerline cylindrical lock

applications.

Deadbolt

Plug

Cylindrical

Horizontal Adjustment: If there is play

in the door when closed; the keeper

shims may be used to minimize play.

Keeper

Sliding Shim

1. Place the folded template square to the frame. Horizontally align

holes marked on the template with the mounting holes in frame.

2. Peel adhesive backing and paste the folded template square to the

frame.

3. Carefully cut the frame inside the un-shaded area marked on the

template. Install strike per installation instructions ISF2

For Cutting ANSI Prep Frames

NOTE: Specications subject to change without notice.

* Dimension F is measured from face of mounting tab to face of

frame.

** Dimension X on the drawing is determined by the vertical

centerline of the door. If the latch incorporates a deadlocking pin

additional steps will be necessary to ensure proper operation of the

deadlocking pin. Measure the thickness of the deadlocking pin and

add this thickness to Dimension X to relocate the vertical centerline an

appropriate distance on the frame.

MEASUREMENT

FRACTIONAL

INCHES

DECIMAL

INCHES

METRIC

A 1-1/4” 1.250 31.75

B 4-7/8” 4.875 123.83

C 3-3/8” 3.375 85.73

DF + 1-7/16” F + 1.438 F + 36.51

E 3/8” 0.375 9.53

F 3/16”* 0.188* 4.76*

G 1-11/16” 1.688 42.86

X Vertical Centre Line of Door

Lock and Mounting Face Plate**

K 4-1/8” 4.125 104.78

M 12-24 N/A N/A

Z 3-5/16” 3.315 84.14

Frame Prep Dimensions

Special Features

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	ES96

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba ES96 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Dormakaba DKX Type IV Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox Airvox SW695 Manual

15 Juni 2025

Stiga SBC 635 KD Manual

15 Juni 2025

Cleveland 36CGM300 Manual

15 Juni 2025

Gourmia GTF7970 Manual

15 Juni 2025

Planet Audio P9630B Manual

15 Juni 2025

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025

Lavex 842CD12VST12 Manual

15 Juni 2025

Marshall RCP-PLUS Manual

15 Juni 2025

Hughes & Kettner BassForce XL Manual

15 Juni 2025

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025