Dormakaba J300 Manual

Dormakaba Ikke kategoriseret J300

Læs gratis den danske manual til Dormakaba J300 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Dormakaba J300, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
J300 Interconnected Lock
Installation Instructions
76019635 03/18 www.dormakaba.us
.. Place latch into door edge.
Orient with beveled edge of latch
facing door jamb.
.. Secure with two - x /” combo
screws.
Dead bolt
housing
ADJUST BACKSET PRIOR TO
INSTALLATION (IF NECESSARY)
.. : Extend dead bolt
• Turn cross drive with screwdriver.
.. Set backset:
• Twist dead bolt housing; push/pull
to appropriate backset.
.. Lock backset:
• Twist housing back to lock in place.
Adjust for door thickness
NOTE: Lock comes adjusted for 1-3/4”
door from the factory.
.. Align so center of chassis is in line
with center of latch.
.. Rotate outside rose assembly to
adjust for proper door thickness.
.. Secure inside
mounting plate
to door.
.. Secure with two
- x -/”
screws.
Install chassis
.. Slide lock assembly into face
of door.
Be sure to engage the inner
latch mechanism of the
chassis with the back of the
latch as shown.
SECURE DEAD BOLT
ASSEMBLY: (J, J)
.. Insert dead bolt sleeve
into exterior face of door.
1 Interconnected lock installation
. Install latch . Install dead bolt latch
. Install lock assembly . Install inside mounting
plate
NOTE: The raised
features on the
mounting plate should
face outward.
DO NOT
OVERTIGHTEN!
. Install dead bolt cylinder assembly (J310, J353) or indicator assembly (J346)
PART LIST
 - DEAD BOLT CYLINDER HOUSING
 - CYLINDER GUARD ROSE
 - CYLINDER GUARD
 - CYLINDER
 - CYLINDER RETAINING PLATE
 - DEAD BOLT SLEEVE
 - INSIDE MOUNTING PLATE
 - /- X -/” SCREWS (X)
 - ESCUTCHEON ASSEMBLY
 - - X /” SCREWS (X)
 - INSIDE LEVER
 - - X -/” SCREWS (X)
 - DEAD BOLT LATCH
 - - X /” COMBO-SCREWS (X)
 - LATCH
 - LOCK ASSEMBLY
 - INDICATOR ASSEMBLY (J)
Tools required
# Cross drive screwdriver







screw
Beveled
edge
.. Retract dead bolt.
.. Place dead bolt latch in door edge.
Orient with cross drive towards the
bottom. (Fig A)
.. Secure with two - x /” combo
screws.
From 2-3/4” to 2-3/8”
and vice versa
[2-3/8”
backset]
[2-3/4”
backset]
Center of
latch
Chassis Outside rose
assembly
Latch
Chassis
Raised
features
.. Secure dead bolt (J,
J) or indicator (J)
through inside mounting
plate.
.. Use two ⁄- x -⁄”
screws.
Inside
mounting
plate
Fig 2A
Cross
drive
SECURE INDICATOR ASSEMBLY
(J346):
.. Prepare tailpiece:
• ENSURE TAILPIECE IS
HORIZONTAL and ‘VACANT’
SHOWS IN WINDOW. Cross
drive
Tailpiece
.. Slide indicator through deadbolt housing, so it
engages with cross drive in dead bolt latch.
Tailpiece
CCW CW
CCW CW
Tailpiece
Indicator
.. Prepare tailpiece:
• LH/LHR: turn
tailpiece
CLOCKWISE
• RH/RHR: turn
tailpiece
COUNTER-
CLOCKWISE
TAILPIECE MUST BE
HORIZONTAL.
.. Insert cylinder
assembly through
cylinder rose/guard.
.. Slide tailpiece
through dead bolt
housing, so it engages
with cross drive in
dead bolt latch.
ENSURE TAILPIECE
IS HORIZONTAL.
Dead bolt
sleeve
Cylinder
rose/
guard
Tailpiece
Cylinder
assembly
Cross
drive
Some parts hidden
for easier viewing
Window
76019635 03/18 www.dormakaba.us
OUTSIDE LEVER REMOVAL
2A.1 Insert key in outside lever.
2A.2 Turn and hold at 90°. IN EITHER DIRECTION
(Fig A)
2A.3 Using pick, depress lever catch through pick
hole and remove lever.
2A.4 Remove key. (Fig B)
2A.5 Remove lever insert and cylinder. (Fig C)
REMOVAL
1.8.1 Wood frame applications only: insert
dead bolt reinforcement.
1.8.2 Secure with two 3” [76] wood screws
[pre-drilled as needed].
1.8.3 Insert each dust box and strike.
1.8.4 Secure each with two
8-32 x 3/4” combo screws.
Non-wood doors
Fig C
Cylinder
Lever
insert
Fig B
Lever
catch
Hinge Hinge
Exterior side of door
Interior side of door
Left hand door (LH)
Left hand reverse
door (LHR)
Right hand reverse
door (RHR)
Right hand door (RH)
HANDING REFERENCE
1.7.1 Secure
escutcheon to
mounting
plate.
1.7.2 Use two
10-32 x 11/16”
screws.
Dead bolt
tailpiece should
be oriented
such that it
engages
mechanism in
back of
escutcheon
assembly.
Tools required
Lever pick
2 Removing and reassembling outside lever, and dead bolt (cylinder changes)
Tailpiece
(horizontal)
Fig D
IncorrectCorrect
Handing direction
“RIGHT” Right/Right hand reverse
“LEFT” Left/Left hand reverse
Semi-circle
opening
Pick
Small
hole
Small
window
Small
hole
Small
window
Small
window
RIGHT
LEFT
RIGHT
LEFT
1.6.1 Insert pick into
small hole in
semi-circle
opening in
back of
escutcheon.
1.6.2 Move pin
around until
appropriate
door handing
direction
appears in
small window.
1.6 1.7 Handing adjustment Install escutcheon and lever
Dead bolt
tailpiece
1.7.3 Push inside lever onto
spindle until it clicks
into place.
Inside
lever
1.8 Install strikes
STRIKE PART LIST
1 - DEAD BOLT STRIKE PLATE
2 - DEAD BOLT DUST BOX
3 - DEAD BOLT REINFORCEMENT
4 - LATCH DUST BOX
5 - LATCH STRIKE PLATE
6 - 3” WOOD SCREWS
7 - 8-32 X 3/4” COMBO SCREWS
Wood doors
4
712
5
1
7
3
564
2
90°
Fig A
Pick
hole
Pick
90°
Fig E
OUTSIDE LEVER REINSTALLATION
2A.6 Replace with new cylinder and
reinstall lever insert. (Fig C)
BE SURE TAILPIECE IS HORIZONTAL.
(Fig D)
2A.7 Press outside lever onto spindle until it
contacts lever catch.
(Fig E)
2A.8 Insert key, turn IN EITHER DIRECTION
and hold at 90°.
2A.9 Press lever fully onto spindle until it
clicks into place.
2A.10 Release key.
DEAD BOLT REMOVAL
2A.1 Using pick, depress lever catch
through pick hole and remove lever.
See Fig. B in prior step for reference.
2B.2 Remove escutcheon assembly
(10-32 x 11/16” screws).
2B.3 Remove two 1/4-20 x 2-3/8” screws
connecting inside mounting plate to
dead bolt cylinder assembly.
2B.4 Remove cylinder assembly.
2B.5 Remove screw in back of dead bolt
cylinder assembly.
2B.6 Remove cylinder retaining plate.
2B.7 Remove cylinder from back of
cylinder housing.
DEAD BOLT REINSTALLATION
2B.8 Replace with new cylinder into
cylinder housing.
2B.9 Reinstall cylinder retaining plate.
• Orientation: raised features face
toward door.
2B.10 Secure with screw.
ENSURE TAILPIECE IS HORIZONTAL AND
CORRECTLY TIMED. (See step 1.5.2A/B
for proper timing.)
Dead
bolt
cylinder
assembly
Screw
1/4-20 x 2-3/8”
screws (x2)
Escutcheon
assembly
10-32 x 11/16”
screws (x2)
Cylinder
retaining
plate
Tailpiece
Cylinder
housing
Dead bolt cylinder assembly
2B.11 Reinstall dead bolt
assembly.
2B.12 Secure with two
1/4-20 x 2-3/8” screws
through mounting plate.
2B.13 Reinstall escutcheon
assembly.
2B.14 Reinstall lever.

Produkt Specifikationer

Mærke: Dormakaba
Kategori: Ikke kategoriseret
Model: J300

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba J300 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Dormakaba Manualer

Dormakaba

Dormakaba Keyscan EC1500 Manual

21 August 2024
Dormakaba

Dormakaba RCI S2500A Manual

21 August 2024
Dormakaba

Dormakaba EAC Manual

21 August 2024
Dormakaba

Dormakaba CLM9000 Manual

21 August 2024
Dormakaba

Dormakaba DKX Type III Manual

21 August 2024
Dormakaba

Dormakaba 9800 Manual

21 August 2024
Dormakaba

Dormakaba HSW-GP Manual

21 August 2024
Dormakaba

Dormakaba DKX-10 Manual

21 August 2024
Dormakaba

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024
Dormakaba

Dormakaba DKX Type IV Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Premium Levella

Premium Levella PWS103 Manual

17 Juni 2025
Intermatic

Intermatic FD30MH Manual

17 Juni 2025
Life On Products

Life On Products LCAF003 Manual

17 Juni 2025
Roland

Roland PDS-2 Manual

17 Juni 2025
Tekron

Tekron TTM 01-G Manual

17 Juni 2025
Hansgrohe

Hansgrohe AXOR Uno 45004250 Manual

17 Juni 2025
Brady

Brady PLO23 Manual

17 Juni 2025
Tekron

Tekron Isolated Timing Repeater Manual

17 Juni 2025
Pulsar

Pulsar Superglide 2 Manual

17 Juni 2025
Hansgrohe

Hansgrohe Ecostat S Manual

17 Juni 2025