Dormakaba La Gard 1947 Manual

Dormakaba Ikke kategoriseret La Gard 1947

Læs gratis den danske manual til Dormakaba La Gard 1947 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Dormakaba La Gard 1947, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Opening the lock – Using the

OPENING INDEX

The lock is shipped with the factory

combination of 50. To open, turn dial to the

LEFT passing 50 at least ﬁ ve times then

stop when 50 lines-up with the OPENING

Index. Turn RIGHT until dial stops, this will

retract the bolt.

To open the lock using a set combination,

for EXAMPLE 10-20-30-40, use the

following procedures:

Using the OPENING Index (see Figure 1)

1. Turn the dial to the LEFT (counter-clockwise) at least ﬁ ve complete rotations to clear

the lock; the lock is now ready to accept the combination. Never spin the dial to clear

the lock.

2. Using the OPENING index, turn the dial RIGHT (clockwise) passing the ﬁ rst number

in the combination [10] four times. Then stop exactly on the number [10] the ﬁ fth time.

3. Turn the dial LEFT (counter-clockwise) passing the next number in the combination

[20] three times. Then stop exactly on the number [20] the fourth time.

4. Turn the dial RIGHT (clockwise) passing the next number in the combination [30] twice.

Then stop exactly on the number [30] the third time.

5. Turn the dial LEFT (counter-clockwise) passing the last number in the combination

[40] one time. Then stop exactly on the number [40] the second time.

6. Turn the dial to the RIGHT (clockwise) to open the lock. The lock bolt is fully

retracted when the dial no longer turns right.

To lock the combination lock, turn the dial ﬁ ve complete rotations to the LEFT.

Change the combination – Using the CHANGING INDEX

To change the combination, you will need to know the existing combination and have a

LA GARD 4-Wheel change key (P/N 1315). When selecting a combination choose a four

number sequence from 0 - 99, for security purposes. It is recommended that you do not

select a combination from personal data (such as birth date, phone number, etc). Never

select numbers 0 to 20 as the LAST NUMBER of the combination; this is the “Forbidden

Zone.”

OPERATING AND CHANGING INSTRUCTIONS

4-Wheel Locks

Group 1 Locks

-205 v2 •

4/08 Kaba Mas LLC

Page 1 of 2

Figure 1

To change the combination, you must ﬁ rst open the safe door by dialing the existing

combination using the OPENING index. Note: before changing the combination verify

that the dial stopped between 90 and 0 on the OPENING index when the bolt is fully

retracted.

Setting a Combination – Using the CHANGING INDEX

Dial the existing combination as previously described using the CHANGING Index (see

Figure 1). STOP the dial on the fourth number of the combination.

1. Insert the change key into the change key

hole (see Figure 2). If the change key does

not go in easily, the wheels are not aligned

for changing. Redial the existing

combination using the CHANGING Index.

2. Turn the change key to the RIGHT until

it stops (approximately one-quarter turn).

Leaving the key in the lock, set the new

combination. EXAMPLE 10-20-30-40

3. Next turn the dial to the LEFT (counter-

clockwise) at least ﬁ ve complete rotations to

clear the lock; the lock is now ready to

accept the new combination. Never spin the dial to clear the lock.

4. Using the CHANGING index, turn the dial RIGHT (clockwise) passing the ﬁ rst number

in the combination [10] four times. Then stop exactly on the number [10] the ﬁ fth time.

5. Turn the dial LEFT (counter-clockwise) passing the next number in the combination [20]

three times. Then stop exactly on the number [20] the fourth time.

6. Turn the dial RIGHT (clockwise) passing the next number in the combination [30] twice.

Then stop exactly on the number [30] the third time.

7. Turn the dial LEFT (counter-clockwise) passing the last number in the combination [40]

one time. Then stop exactly on the number [40] the second time.

8. Turn the change key to the LEFT and remove the change key. The new combination

has been set.

To test, dial the new combination using the OPENING index. ALWAYS perform this test

with the safe door open! Test several times before closing the safe door. Also check that

the dial stops between 90 and 0 on the OPENING index when the bolt is fully retracted.

Note: When locking the safe always turn the safe handle, if present, to the locked

position (bolts extended) before turning the lock dial (ﬁ ve complete rotations to the

LEFT) to relock. If you notice any resistance DO NOT force the dial to turn. This may

cause damage to the lock.

-205 v2 •

4/08 Kaba Mas LLC

Page 2 of 2

Figure 2

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	La Gard 1947

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba La Gard 1947 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

2N Telecommunications EasyGate Pro Manual

11 Juli 2025

Sitecom CH-1105 Manual

11 Juli 2025

Yamazen OSG-65R Manual

11 Juli 2025

Yamazen YMW-3 Manual

11 Juli 2025

Universal Audio Apollo x8p Gen 2 Manual

11 Juli 2025

Icon RealTime Portal Manual

11 Juli 2025

InfiRay RICO Mk2 LRF RH50R Manual

11 Juli 2025

Microchip MCP48FEB18 Manual

11 Juli 2025

Yamazen GCB-3 Manual

11 Juli 2025

Yamazen MNR-12604CJ Manual

11 Juli 2025