Dormakaba La Gard 1985 Manual

Dormakaba Ikke kategoriseret La Gard 1985

Læs gratis den danske manual til Dormakaba La Gard 1985 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Dormakaba La Gard 1985, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

(P/N) 723.069 Rev C

07/15

•

Page 1 of 2

OPEN LOCK WITH THE FACTORY

COMBINATION

LA GARD mechanical locks are shipped with

the factory combination of . Open using the50

OPENING Index:

4 x Turn dial to the LEFT (CCW) passing

“50” three times. Then stop exactly on the

number “50” the fourth time.

Turn the dial to the RIGHT (CW) until it

stops and the bolt retracts.

NOTE: Variations in the alignment of the dial ring during installation could cause

the Factory Combination of 50 to vary slightly, either up or down by one or

two numbers.

NOTE: If using the VisionGard Dial (2085 or 2090 Series) and a lock with the

factory combination, the lock will open on 47.

NOTE: When dialing a combination, if you passed the number on which you

intended to stop, you cannot reverse the dial to correct. The opening procedure

must be repeated from the beginning.

IMPORTANT NOTE: Change the combination before putting the lock into operation.

SET COMBINATION

To change the combination, you will need to know the existing combination

and have a LA GARD change key (P/N 1307).

CAUTION: When selecting a combination, choose a three number sequence

from 0 - 99. NEVER select numbers 0 to 20 as

the LAST NUMBER of the combination. This is

the “Forbidden Zone” and can cause the lock

to malfunction. For security purposes, do not

select a combination from personal data such

as birth date, phone number, etc. You also

should not share the combination. It is a secret.

1. Dial the existing combination using the

CHANGING Index. (Figure 1.)

2. STOP the dial on the third number of

the combination.

3. Insert the change key into the change key hole. (Figure 2.)

OPERATING & CHANGING INSTRUCTIONS

LA GARD MECHANICAL

Group 1, Group 2 & Group 2M Locks

Figure 1

Figure 2

(P/N) 723.069 Rev C

07/15

•

Page 2 of 2

NOTE: If the change key does not go in easily, the wheels are not aligned. Repeat

steps 1 - 3.

4. Turn the change key to the RIGHT (CW) one-quarter turn until the key

stops. (Figure 2.) Leave the change key in the lock while setting the

new combination.

5. Next turn the dial to the LEFT (CCW) at least four complete

rotations to clear the lock. The lock is now ready to accept the

new combination.

CAUTION: Do not spin the dial to clear the lock.

6. Set the new combination using the CHANGING Index:

EXAMPLE COMBINATION: 10-20-30

Turn the dial LEFT (CCW) passing the ﬁrst number in the combination

(10) three times. Then stop exactly on the number “10” the fourth time.

Turn the dial RIGHT (CW) passing the next number in the combination

(20) two times. Then stop exactly on the number “20” the third time.

Turn the dial LEFT (CCW) passing the last number in the combination

(30) one time. Then stop exactly on the number “30” the

second time.

4 x

3 x

2 x

7. Hold the Dial to prevent movement and turn the change key to the LEFT

(CCW) one quarter turn.

8. Remove the change key. The new combination is now set.

ALWAYS perform the combination test with the safe door open! Test the new

combination several times using the opening procedure below.

OPEN LOCK WITH A SET COMBINATION

Dial the set combination using the OPENING Index.

EXAMPLE COMBINATION: 10-20-30

Turn the dial LEFT (CCW) passing the ﬁrst number in the combination

(10) three times. Then stop exactly on the number “10” the fourth time.

Turn the dial RIGHT (CW) passing the next number in the combination

(20) two times. Then stop exactly on the number “20” the third time.

Turn the dial LEFT (CCW) passing the last number in the combination

(30) one time. Then stop exactly on the number “30” the second time.

Turn the dial to the RIGHT (CW) until it stops and the bolt retracts.

4 x

3 x

2 x

NOTE: When locking the safe, always turn the safe handle to the locked position (bolt

extended) before turning the lock dial four complete rotations to the LEFT (CCW) to

relock. If you notice any resistance, DO NOT force the dial to turn. This may cause

damage to the lock.

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	La Gard 1985

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba La Gard 1985 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IMC Networks 232CL9R Manual

14 September 2025

Varta Speed Charger 57955 Manual

14 September 2025

Melissa & Doug 9336 Manual

14 September 2025

Opus dataPREDATOR Manual

13 September 2025

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025

Daewoo AVS1369 Manual

13 September 2025

SolarEdge SE120K-RW08IBNQ4 Manual

13 September 2025

Varta Fast Wireless Charger 57912 Manual

13 September 2025

Hauppauge Colossus Manual

13 September 2025

Contour Wireless Unimouse Manual

13 September 2025