Dormakaba Oracode 480 Manual

Dormakaba Ikke kategoriseret Oracode 480

Læs gratis den danske manual til Dormakaba Oracode 480 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Dormakaba Oracode 480, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

PK3700

2018-06-29 Page 1 of 5

ORACODE 480 - 480i SERIES

INSTALLATION GUIDE FOR DOOR THICKNESS 1 ⁄" " TO 2

! WARNING

1. Please read and follow all directions carefully.

2. Carefully inspect glass, door frame, door etc., to ensure that the recommended procedures will not cause damage.

dormakaba standard warranty does not cover damages caused by installation.

3. Wear safety glasses when making the holes.

4. All the following operations and testing of the lock to be done with door open.

Tools Required

• Safety Glasses

• ⁄" (13mm) Chisel

• ⁄" (3mm) Drill Bit

• ⁄" (4mm) Drill Bit

• 1" Drill Bit or Hole Saw

• 2 ⁄" (54mm) Hole Saw

• Drill

• Awl or Center Punch

• Screwdriver, ⁄" slotted

• Phillips Screwdriver (#2)

• Adjustable Square

• Tape Measure

DOOR PREPARATION

INSTALL STRIKE ON WOOD FRAME INSTALL STRIKE ON STEEL FRAME

ADJUST BACKSET OF DEADBOLT INSTALL DEAD BOLT IN DOOR

A = Backset = 2 ⁄" (70mm) or 2 ⁄" (60mm)

1. Determine which template fits your 480 lock installation, either 2 ⁄"

(60mm) or 2 ⁄" (70mm) backset.

2. Place appropriate template (supplied) onto door and mark holes.

3. Drill holes as per dimensions on the template, the 1" (25mm) hole to be

on the center line of door thickness.

4. Mortise door edge for dead bolt face plate.

5. Drill 2 ⁄" from both sides of the door to prevent unsightly damage.

For maximum

security,

install

reinforcing

plate.

Door stop

Install long screws in

door stop side.

Do not remove tape

Slot at the bottom

The dead bolt is pre-set at 2 ⁄" (70mm)

backset. Proceed as illustrated to change to

2 ⁄" (60mm) backset, if required.

1" (25mm)

2 ⁄" (54mm) Hole saw

1A 1B

2 3

PARTS LIST

1. Outside Housing Assembly (1)

2. Bar Code Label (1)

3. Outside Housing Gasket (1)

4. Dead Bolt (1)

5. Inside Trim Assembly (1)

6. Machine Screw, Pan Head, SS, PH #3, 12-24 (1)

7. Machine Screw, Pan Head, ZP, PH #2, 8-32 (2)

8. Machine Screw, Pan Head, ZP, PH #2, 6-32 (2)

9. Split Lock Washer, No. 8, SS 18-8 (2)

10. Split Lock Washer, No. 12, SS (1)

11. Machine Screw, Flat Head, Brass, PH #2, 8-32 x ⁄" (2)

12. Dust Box (1)

13. Striker Plate (1)

14. Wood Screw, PH #2, #8 x 1" (4)

15. Wood Screw, PH #2, #8 x 3” (2)

16. Reinforcing Plate (1)

17. Tail Piece Door 1 ⁄" to 2" (1)

18. Cap (1)

19. Override Key (May be shipped separately) (1)

20. Battery Cell, AA Alkaline (3)

21. Key Cylinder (May be shipped separately) (1)

22. Inside Cover (1)

23. Machine Screw, Flat Head, SS 304, PH #2, 6-32 x .750 (1)

LOCK DIAGRAM

When installing the lock, please carefully slide post

through dead bolt holes.

KEY OVERRIDE CYLINDER

If cylinder is not already assembled in the lock,proceed as follows:

ADJUST LOCK HANDING ON OUTSIDE HOUSING ASSEMBLY

4. Wire must not be pinched

when re-installing back plate

5. Re-assemble back plate using

screws as shown

1. Remove 4 screws

2. Remove back plate

May be necessary to

loosen post to remove

back plate

“Retaining ring”

opening at 12 o’clock

“Wire ring” opening far

from slot Groove at 6 o’clock Groove at 12 o’clockRotate to change

from RH to LH

Hold from rotating

Slot Slot

If required, re-tighten post

while making sure not to

pinch retaining ring

Override Switch

WARNING

Posts are mandatory for Fire

Certification and should never

be removed.

Right hand (RH) Left hand (LH)

Install key cylinder

ASSEMBLE TAIL PIECE REMOVE INSIDE COVER ASSEMBLE OUTSIDE HOUSING

Click in place

Run cable through door

and under the dead bolt

Remove tape

Run cable through inside

trim back plate slot

6 7 8

INSTALL INSIDE TRIM ASSEMBLY

INSTALL INSIDE COVER

1. All screws should be tightened properly

2. Connect batteries after tightening all screws

PK3700

2018-06-29 Page 2 of 5

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	Oracode 480

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba Oracode 480 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman AUTO300 WIFI Manual

1 August 2025

Navman AUTO550 DUAL Manual

1 August 2025

Newline DV-15023H Manual

1 August 2025

Navman MiVue 720 Manual

1 August 2025

Etna HF2008 Manual

1 August 2025

Grundig 40 VLE 7630 WP Manual

1 August 2025

Navman MiVue 600 DC Manual

1 August 2025

Navman MiVue 830DC Manual

1 August 2025

Navman MiVue 840 Manual

1 August 2025

Navman MiVue 880 DC Manual

1 August 2025