Dormakaba RCI 0163 Manual

Dormakaba Ikke kategoriseret RCI 0163

Læs gratis den danske manual til Dormakaba RCI 0163 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Dormakaba RCI 0163, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION

RCI 0163 / RCI 0163LM

SURFACE MOUNTED RIM STRIKE

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

Fail Secure = Fail Locked = FL AC = Alternating Current DC = Direct Current

Intermittent Duty = Energized less than 1 minute with 1:5 duty ratio Continuous Duty = Energized 1 minute or more

IS0163 PCN18041

R09-18GR-3

Important: The RCI 0163 Electric Strikes should never be used as a door stop.Please install stops on frame in

appropriate locations. Ensure the exit device functions as intended for life safety concerns by verifying electric strike and

exit device compatibility. Maximum latch projection is essential to obtain full holding force.

Since the RCI 0163 strike is fail secure the local Authority Having Jurisdiction shall be consulted with regard to the use

of selected panic hardware to ensure emergency exit from the secured area.

Installations of this RIM strike qualify as “Indoor Use Only” when not continuously exposed to an outdoor environment.

Catalog Specifications

MODE VOLTAGE CURRENT DUTY PEAK AMPS OHMS

Fail Secure 12V AC Intermittent 0.15 37

Fail Secure 12V DC Continuous 0.27 37

Fail Secure 24V AC Intermittent 0.33 37

Fail Secure 24V DC Continuous 0.14 148

Fail Secure 11-16V AC Intermittent 0.13-0.19 37

Electrical Latch Monitor

Speciﬁcation:

• 12VDC, 1A, resistive load

Note: Contacts identiﬁed on the

harness sleeve are indicated with the

keeper in a closed and locked condition,

with no latch present

Dimensional Details

UL 294 Performance Ratings:

Access Control Line Security : Level I

Destructive Attack : Level I

Endurance : Level IV

Standby Power : Level I

Instructions

1. Determine the horizontal centerline of the exit device latch and transfer centerline to the frame stop.

2. Position the template onto the frame aligning with centerline and against the closed door. Center-punch the two

mounting holes and the wire access hole as shown.

3. Drill and tap the two mounting holes and drill the wire access hole(s).

4. Test fit electric strike to ensure full latch engagement.

5. Make wire connections from the power source to the appropriate wire harness supplied. Use 12VDC wire harness for

12VDC, 12-24VAC or 11-16VAC input power. Use 24VDC wire harness for 24VDC input power only.

NOTE: Overheated or burnt coils caused by incorrect input voltage / wire harness combinations will not be

covered under warranty

6. Connect monitor wires of LM model.

7. Mount the electric strike with 1/4-20 UNC screws provided in the horizontal mounting holes (the outer slots).

Adjust electric strike horizontally until exit device latch fully engages with the door closed.

NOTE: Ensure a 1/16” [1.5mm] clearance between

exit device latch and the electric strike keeper is

maintained. Failing to do so will preload the strike

and in turn will not allow the strike to release the

door upon energizing.

8. Tighten the two mounting screws and check operation. Adjust the horizontal position of electric strike as required.

9. Use the electric strike as a template to mark the two locking holes. Remove strike. Drill & tap for 1/4-20 UNC locking

screws. Using the 1/4-20 UNC screws provided secure the electric strike through the locking holes.

10. A dead latch shim is provided in each hardware kit. This can be used to prevent a deadlatch from falling into the

strike cavity.

1/16"

MINIMUM

STRIKE KEEPER

LATCH

NOTE: NOTE: * Wire access hole locations are relative to the exit device orientation. Second wire access hole required for RCI 0163LM only

NOTE: Not to scale. Specifications are subject to change without notice.

M3 SCREW

DEADLATCH SHIM

KEEPER

LOCKING

SCREW

(2 PLACES)

FRAME

EXIT DEVICE

DOOR STOP

#1/4-20 UNC

(2 PLACES)

5/8" (16mm)

WIRE ACCESS HOLE

(LM SWITCH)

5/8" (16mm)

WIRE ACCESS HOLE

(POWER)

MOUNTING SCREW

(2 PLACES)

DOOR

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	RCI 0163

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba RCI 0163 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Dormakaba DKX Type IV Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox Airvox SW695 Manual

15 Juni 2025

Stiga SBC 635 KD Manual

15 Juni 2025

Cleveland 36CGM300 Manual

15 Juni 2025

Gourmia GTF7970 Manual

15 Juni 2025

Planet Audio P9630B Manual

15 Juni 2025

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025

Lavex 842CD12VST12 Manual

15 Juni 2025

Marshall RCP-PLUS Manual

15 Juni 2025

Hughes & Kettner BassForce XL Manual

15 Juni 2025

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025