Dormakaba RCI 8360 Manual

Dormakaba Ikke kategoriseret RCI 8360

Læs gratis den danske manual til Dormakaba RCI 8360 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Dormakaba RCI 8360, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

INSTALLATION

RCI 8360

MiniMag® MORTISE ELECTROMAGNETIC LOCK

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

1. Hold lock against frame at desired level. Mark the lock’s horizontal

centerline on the frame and transfer that mark to the door.

2. Determine the vertical centerline of the door thickness and mark

this on both the door and the frame.

3. Using these centerline references, cut out the lock mortise in

the frame as illustrated.

4. Temporarily fasten the two mounting tabs under the lock

flanges. Insert the lock assembly into the frame cavity until the

tabs are resting on top. Mark the location of the tab mounting

holes.

5. Drill and countersink these four holes to accept the 3/16” screws

provided.

6. Remove tabs from lock. Mount the tabs inside the frame.

7. Set voltage dipswitches as follows:

12VDC operation = 1 and 2 are On / 3 is Off

24VDC operation = 1 and 2 are Off / 3 is On (factory setting)

Connect the positive (+) power lead to the red and the negative

(-) lead to the black wire.

Connecting wire should be of sufficient gauge for the lock being

installed and the distance being run. See table on page 3 for

current draw specifications.

8. RLS (Remote Lock Status)

This feature can detect the quality of the locking bond between

the surface of the magnet and the armature plate. The

sensitivity of this feature is such that a foreign object with a

thickness of .007” (.18mm) is sufficient to allow the sensor to

detect a problem.

Due to the sensitivity of this feature and the necessity to

maintain a reliable locking surface, these surfaces must be kept

free of contaminating materials. Both the lock surface and the

armature plate must be cleaned periodically with a non-abrasive

cleanser. Proper alignment of the armature plate and magnet is

required to ensure proper function of sensor.

The 3 RLS lead wires at the lock corner are: Red = Normally

Closed, Black = Common, Green = Normally Open with the

door open / unlocked.

IS8360 PCN18041

R09-19GR-1

Instructions

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available with this

product, a survey and assessment of the physical area in which

the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be strong

enough to meet or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not hinder

or create a potential safety hazard to authorized personnel

accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must make

a determination of the optimal mounting method for this specific

application.

7. Do not install this product on the exterior of buildings.

8. Do not use as a doorstop. This will void warranty.

9. Installation of this product should be done by an experienced

installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound be

applied to all screws during installation to reduce chance of screws

loosening over extended time.

WARNING: Improper installation, maintenance, inspection or

usage of the product or any related accessories or parts may

cause the electromagnetic lock, armature plate and associated

hardware to disengage and fall, causing serious bodily injury

and property damage. dormakaba Canada Inc .and/or dormakaba

USA Inc. will not be liable to the installer, purchaser, end user

or anyone else for damage or injury to person or property due

to improper installation, care, storage, handling, maintenance,

inspection, abuse, misuse or act of God or nature involving this

product or any related accessories or parts.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	RCI 8360

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba RCI 8360 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba CenTran 4 Manual

19 Oktober 2025

Dormakaba Crane S1 Manual

19 Oktober 2025

Dormakaba Auditcon T52 Manual

18 Oktober 2025

Dormakaba 12C Manual

18 Oktober 2025

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Iogear GUE2118 Manual

29 Oktober 2025

Calorex Delta DT 16 Manual

29 Oktober 2025

Abus Comfion FUSH80010 Manual

29 Oktober 2025

Venom VS3605 Manual

29 Oktober 2025

EtherWAN EX48000 Manual

29 Oktober 2025

Bissell SpotClean Pro 3624 Manual

29 Oktober 2025

First Alert SMCO600NV-AC Manual

29 Oktober 2025

Owon OWH80Q Manual

29 Oktober 2025

Moen Weymouth S73004EV2BG Manual

29 Oktober 2025

Arozzi Alzare Neo Manual

29 Oktober 2025