Dormakaba RCI 8365 Manual

Dormakaba Ikke kategoriseret RCI 8365

Læs gratis den danske manual til Dormakaba RCI 8365 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Dormakaba RCI 8365, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

INSTALLATION

RCI 8365

MicroMag MORTISE ELECTROMAGNETIC LOCK®

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

1. Mortise Cutouts

Hold lock against frame at desired level. Mark the lock’s horizontal

centerline on the frame and transfer that mark to the door.

Determine the vertical centerline of the door thickness and mark

this on both the door and the frame.

Using these centerline references, cut out the frame lock mortise

and the door armature mortise, as illustrated.

2. Lock Mounting Tabs

Temporarily fasten the two mounting tabs under the lock flanges.

Insert the lock assembly into the frame cavity until the tabs are

resting on top. Mark the location of the tab mounting holes.

Drill and countersink these four holes to accept the 3/16” screws

provided.

Remove tabs from lock. Mount the tabs inside the frame.

3. Wire and Mount Lock

Remove endcap.

Set voltage jumpers as follows:

12VDC operation = two jumpers are used.

Contact pins 1 to 2 and 3 to 4.

24VDC operation = only one jumper is used.

Contact pins 2 to 3. (factory setting)

Connect the positive (+) power lead to the red and the negative

(-) lead to the white wire.

Connecting wire should be

of sufficient gauge for the

lock being installed and the

distance being run.

See page 3 table for current

draw specifications.

Secure lock on tabs in

mortise cavity, carefully applying thread locking compound to the

hardware provided, as in Fig. 1

IS8365 PCN18041

R09-19GR-1

Instructions

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available with this

product, a survey and assessment of the physical area in which

the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be strong

enough to meet or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not hinder

or create a potential safety hazard to authorized personnel

accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must make

a determination of the optimal mounting method for this specific

application.

7. Do not install this product on the exterior of buildings.

8. Do not use as a doorstop. This will void warranty.

9. Installation of this product should be done by an experienced

installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound be

applied to all screws during installation to reduce chance of screws

loosening over extended time.

WARNING: Improper installation, maintenance, inspection or

usage of the product or any related accessories or parts may

cause the electromagnetic lock, armature plate and associated

hardware to disengage and fall, causing serious bodily injury and

property damage. dormakaba Canada Inc. and/or dormakaba

USA Inc. will not be liable to the installer, purchaser, end user

or anyone else for damage or injury to person or property due

to improper installation, care, storage, handling, maintenance,

inspection, abuse, misuse or act of God or nature involving this

product or any related accessories or parts.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	RCI 8365

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba RCI 8365 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba CenTran 4 Manual

19 Oktober 2025

Dormakaba Crane S1 Manual

19 Oktober 2025

Dormakaba Auditcon T52 Manual

18 Oktober 2025

Dormakaba 12C Manual

18 Oktober 2025

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Eschenbach laboCLIP Manual

30 Oktober 2025

Iogear GearPower GPAWC145W Manual

30 Oktober 2025

DeWalt DWST83471 Manual

30 Oktober 2025

Elvid SignalMaster UDX-HS Manual

30 Oktober 2025

First Alert SMCO600NV Manual

30 Oktober 2025

ROCWARE RM702 Manual

29 Oktober 2025

D-MON Manual

29 Oktober 2025

Meliconi Base Wash Evo Manual

29 Oktober 2025

Olimpia Splendid Bi2 SL AIR Manual

29 Oktober 2025

Abus C523–C526 Manual

29 Oktober 2025