Dormakaba RCI 8375 Manual

Dormakaba Ikke kategoriseret RCI 8375

Læs gratis den danske manual til Dormakaba RCI 8375 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Dormakaba RCI 8375, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION

RCI 8375

SURFACE MICROMAG® ELECTROMAGNETIC LOCKS

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

IS8375

PCN18041

R03-20GR-1

Pre-Installation Instructions

1. This product must be installed according to all applicable building

and life safety codes.

2. Due to the variety of mounting configurations available with this

product, a survey and assessment of the physical area in which

the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally sound

prior to installation of the electromagnetic lock. The structural

integrity of the mounting surfaces must be strong enough to meet

or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not hinder

or create a potential safety hazard to authorized personnel

accessing the protected area.

6. Because electromagnetic locks are used in a variety of applications

and different door frame configurations, an experienced installer

with knowledge of this product must make a determination of the

optimal mounting method for this specific application.

7. The components, hardware, installation instructions and mounting

template included with this product are intended for use on

outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories not included with this product must be used

in the following applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that do not have a door frame

• Hollow metal or wood frames where the door stop is

not thick enough to allow the product to be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to be

mounted low enough to meet the magnet surface

Refer to the page 4 Product Accessories Guide for further

information. Accessories may impact holding force.

11. Installation of this product should be done by an experienced

installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound be

applied to all screws during installation to reduce chance of screws

loosening over extended time.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

Fig. 1.

8375 Mounting

Plate Removal

Fig. 2 – 8375 Voltage Selection Jumper Setting

12VDC Operation 24VDC Operation

(Factory Setting)

Electromagnetic lock installations must conform to local fire codes, National

building codes and Life Safety Codes.

Mounting

Bracket

Releases captive

mounting screws

NOTE: All dormakaba electromagnetic locks must be powered with

filtered and regulated DC power supplies such as the DKPS Series UL

Listed power supply. dormakaba offers a full line of power supplies and

switching devices that are suitable for use with the 8375 Series locks.

To Ensure Instant Release All switching devices must be wired in

between the DC power source and the positive terminal of the lock in

Fig 3.

Switching the negative power supply line will not allow the lock to

release immediately. dormakaba electromagnetic locks contain MOV’s

for surge suppression and do not require any additional suppression to

be added during installation. The installation of diodes across the lock

input terminals will cause a delay in release.

Fig. 3 – Power Connections

SWITCH

INCORRECT

CORRECT

SWITCH

FILTERED DC SUPPLY

Mount the electromagnetic lock to the door frame as outlined on the

installation template included with the product.

NOTE: During installation of the armature plate to the door it is essential

that the armature plate remains movable. The armature plate must be

allowed to pivot on the center-mounting bolt to allow proper alignment with

the magnet surface. If the plate is not aligned with the magnet surface, the

lock may lose holding force or not lock at all.

The head of the armature mounting bolt ships with a rubber washer affixed

to it. This washer should project slightly beyond the surface of the armature

plate. This is to allow the washer to expand when power is removed and

break the air vacuum between the plate and the magnet surface. If this

washer is removed or trimmed the lock will appear to have some holding

force even when power is removed.

For added safety, thread locking compound has been provided for the armature

plate bolt and the four captive electromagnetic lock mounting screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware to

disengage and fall, causing serious bodily injury and property damage.

dormakaba Canada Inc. and/or dormakaba USA Inc. will not be liable to

the installer, purchaser, end user or anyone else for damage or injury to

person or property due to improper installation, care, storage, handling,

maintenance, inspection, abuse, misuse or act of God or nature involving

this product or any related accessories or parts.

Route the power supply connecting wire through the door frame and into the

wire access hole in the top of the magnet housing. Connecting wire should

be of sufficient gauge for the lock being installed and the distance being run.

Installation Instructions

Inspection and Maintenance

This product and all related accessories or parts must be inspected

and maintained on a . Contacting surfaces of quarterly basis

the electromagnetic lock and armature plate must be kept free of

contaminating materials. Surfaces must be cleaned periodically with a

non-abrasive cleaner.

All mounting fasteners must be inspected on a quarterly basis.

When properly installed, the ends of the armature plate allow a slight

movement but the plate will feel secure when grasped at the bolt. There

should be no movement to the mounting bracket or housing of the

electromagnetic lock.

For added safety, thread locking compound has been provided for the

armature plate bolt and the four captive electromagnetic lock mounting

screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware to

disengage and fall, causing serious bodily injury and property damage.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO THE

END-USER UPON COMPLETION OF THE INSTALLATION.

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	RCI 8375

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba RCI 8375 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025