Dormakaba RCI GateMag 8380 Manual

Dormakaba Ikke kategoriseret RCI GateMag 8380

Læs gratis den danske manual til Dormakaba RCI GateMag 8380 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Dormakaba RCI GateMag 8380, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTALLATION

RCI GateMag 8380®

Z BRACKET & POST BRACKET

ELECTROMAGNETIC LOCK ACCESSORY

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

1. Installation of this product should be done by an experienced

installer with knowledge of this product. Read and conform to

each of the Pre-Installation Instructions supplied with your RCI

brand 8380 GateMag®. Failure to conform to the Pre-Installation

Instructions is a misuse of product and could result in serious

bodily injury or property damage. This product must be used only

with an RCI brand 8380 GateMag®.

2. Back mount 8380 GateMag® to stationary post for single gate or

to fixed leaf of gate for double-swing gate per template STEP 2.

3. Using a hammer install the clinch nut into the center hole of

bracket (A) from the back side as shown below.

4. Assemble bracket (A) & bracket (B) together to form a “Z” using

2 screws in each slot. Do not over tighten to allow adjustment.

5. Pass bolt with rubber head through the armature plate. Add 3

washers (steel - rubber - steel) onto bolt. Carefully apply thread

locking compound to the exposed threads. While aligning pins,

drive the bolt into clinch nut on bracket A.

NOTE: Do not over tighten armature plate. It must remain

movable to allow surface alignment with electromagnetic lock.

6. With gate in closed position, carefully align armature plate to

GateMag®’s electromagnetic face. Secure Z bracket assembly to

swinging portion of gate. Make sure there is good contact of lock

with armature plate and tighten adjustment screws.

Washers

(steel-rubber-steel)

M8 Clinch Nut

Armature Adjustment

Bracket A

M5 Counter Sunk Screws

(6 places)

Armature Plate

Armature Bolt

Door Bracket B

Note For proper operation, one :

side of the double gate pair

should be stationary. Lock may

not hold correctly if both gates

swing freely.

1. Installation of this product should be done by an experienced installer with knowledge of this

product. Read and conform to each of the Pre-Installation Instructions supplied with your

RCI brand 8380 GateMag®. Failure to conform to the Pre-Installation Instructions is a

misuse of the product and could result in serious bodily injury or property damage.

This product must be used only with an RCI brand 8380 GateMag ®.

2. Side mount 8380 GateMag® to stationary post per template STEP 2.

3. Using a hammer install the clinch nut into the center hole of the bracket from the backside.

4. Pass bolt with rubber head through the armature plate. Add 3 washers (steel - rubber - steel) onto bolt.

Carefully apply thread locking compound to the exposed threads. While aligning pins, drive the bolt into clinch nut.

5. With gate in closed position, carefully align armature plate to GateMag®’s electromagnetic face.

Secure the bracket to post of sliding gate as required.

Sliding Gate Post Bracket Installations

Swinging Gate “Z” Bracket Instructions

WARNING: Improper installation, maintenance, inspection or use of this or any related product may cause the electromagnet lock, armature plate

and associated hardware to disengage and fall, causing serious bodily injury and property damage. dormakaba Canada Inc. and/or dormakaba

USA Inc.will not be liable to the installer, purchaser, end user or anyone else for damage or injury to person or property due to improper installa-

tion, care, storage, handling, maintenance, inspection, abuse, misuse or act of God or nature involving this or any related product.

NOTE: Not to scale. Specifications are subject to change without notice.

ISTJPB80-2 PCN18041

R09-19GR

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	RCI GateMag 8380

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba RCI GateMag 8380 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba CenTran 4 Manual

19 Oktober 2025

Dormakaba Crane S1 Manual

19 Oktober 2025

Dormakaba Auditcon T52 Manual

18 Oktober 2025

Dormakaba 12C Manual

18 Oktober 2025

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JET TPFA-Z Manual

15 December 2025

Crosley Asheville CF1149 Manual

15 December 2025

Mercusys MC200 Manual

15 December 2025

Growatt ARK 2.5L-A1 Manual

15 December 2025

ALNO MC40244 Manual

15 December 2025

BEKO BG640EXVIXL Manual

15 December 2025

Milwaukee 48-22-9200 Manual

15 December 2025

Growatt ALP 5.0L-E1-AU Manual

15 December 2025

Arçelik A55 A 950 A Manual

15 December 2025

Extron EBP 106 Manual

15 December 2025