Dormakaba RCI VR166 Manual

Dormakaba Ikke kategoriseret RCI VR166

Læs gratis den danske manual til Dormakaba RCI VR166 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Dormakaba RCI VR166, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION

RCI VR166/VR166LMKM

SURFACE MOUNTED VERTICAL ROD STRIKE

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.comISVR166 R12-18TG

Fail Locked = Fail Secure = FL AC = Alternating Current DC = Direct Current

Intermittent Duty = Energized less than 1 minute with 1:5 duty ratio

Continuous Duty = Energized 1 minute or more

Important: Adjust strike as indicated in steps 9 thru 12 to ensure

proper functionality. Ensure the exit device functions as intended for

life safety concerns by verifying electric strike and exit device compatibility.

Maximum latch projection is essential to obtain full engagement.

This product is Fail Secure only.

The local Authority Having Jurisdiction shall be consulted with regard to the use

of selected panic hardware to ensure emergency exit from the secured area.

Installations of this Vertical Rod strike qualify as “Indoor Use Only”

when not continuously exposed to an outdoor environment.

MODE VOLTAGE CURRENT DUTY OHMSPEAK AMPS

Fail Locked 12V AC Intermittent 0.12 52

Fail Locked 12V DC Continuous 0.21 52

Fail Locked 24V AC Intermittent 0.27 52

Fail Locked 24V DC Continuous 0.10 208

UL 294 Performance Ratings:

Access Control Line Security : Level I

Destructive Attack : Level I

Endurance : Level IV

Standby Power : Level I

Catalog Specifications

Wiring Instructions

Use 12VDC wire harness for 12VDC or 12-24VAC input power.

Use 24VDC wire harness for 24VDC input power only.

Attach the red wire to (+) positive of the power supply.

Attach the black wire to the (-) negative of the power supply.

If using AC power, polarity is not observed.

Note: overheated or burnt coils caused by incorrect input voltage/wire harness

combinations will not be covered under warranty.

Electrical Latch & Keeper Monitor Speciﬁcations:

• SPDT switch, 0.1A 24VDC resistive load for LM latch monitor

• SPDT switch, 1A 12VDC resistive load for KM keeper monitor

Note: Contacts identiﬁed on the harness sleeve are indicated with the keeper in a closed

and locked condition, with no latch present

Horizontal

adjustment

mounting holes

Fig. 1

Lock down clamp

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

Frame Prep Detail

1. Close the door and mark the center line of the surface mount latch from door on to the top of the frame.

2. Fold the TVR166 template at the line specified. The folded part is always placed on the door side of frame.

3. Place the template so that the center line previously marked on top of the frame lines up with center line on the

template.

4. If centerlines don’t line up, make sure to horizontally adjust the template so that the latch (on the door) is placed

inside of the box specified on the template.

5. Open the door and carefully tape the template to the frame.

6. Center punch the two 1/4-20 holes on the template. Then drill and tap the 1/4-20 indicators marked.

7. With proper tools mark and cutout the parameters of the cutting lines on the template. Refer to Frame prep details

below. (Fig. 2)

8. Install the VR166 using either one or both Lock down clamps depending on how much room you have from the

vertical side of the frame. Do not fully tighten them yet.

9. Inspect the engagement between the latch and the keeper of lock by opening

and closing the door.

10. The strike can be horizontally adjusted towards or away from the door using

the slotted mounting holes on the faceplate. See Fig. 1.

11. For adjustment in height of the lock please use the 2mm shim provided.

12. Once everything has been adjusted, secure the strike down with either one or both Lock down clamps using

the 1/4-20 screws provided.

Mounting Instructions

(85.5mm)

3-3/8"

(8.0mm)

5/16"

(63.0mm)

2-1/2"

(46.0mm)

1-13/16"

(33.0mm)

1-1/16"

(11.0mm)

7/16"

(23.0mm)

15/16"

THIS IS A NON-HANDED STRIKE,

TOP RIGHT CORNER HAS BEEN

SHOWN ONLY AS A REFERENCE

DOOR CLOSES AND RESTS

ON THIS FACE. THIS IS THE PULL

SIDE OF THE DOOR/OUTSIDE AND

NEEDS CREDENTIALS/FOB TO GET IN

NOTE: Ensure a 1/16" (1.5mm) clearance between latch and the VR166 keeper is

maintained. Failing to do so will preload the strike, which will not allow the strike

to release the door when energized.

1/16”

(1.5mm)

Fig. 2

Dimensions

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	RCI VR166

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba RCI VR166 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite U339-001-FLAT Manual

31 Juli 2025

Tripp Lite IBLOK2-0 Manual

31 Juli 2025

Tripp Lite TR-6FM Manual

31 Juli 2025

L.R.Baggs Element Active System Manual

31 Juli 2025

Tripp Lite Protect It! TLP310USBCW Manual

31 Juli 2025

Tripp Lite PR25 Manual

31 Juli 2025

SolidDrive SD-1G Manual

31 Juli 2025

Tripp Lite PR7 Manual

30 Juli 2025

Wren & Cuff 70's Your Face Fuzz Manual

30 Juli 2025

Advantech WISE-2211 Manual

30 Juli 2025