Dotco 10L2580-36 Manual

Dotco Kværn 10L2580-36

Læs gratis den danske manual til Dotco 10L2580-36 (68 sider) i kategorien Kværn. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Dotco 10L2580-36, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/68
GS-2007
02-2014
Cleco
®
- Dotco
®
EN General Safety
DE Allgemeine Sicherheit
FR Sécurité générale
ES Seguridad General
IT Sicurezza generale
PT Segurança geral
NL Algemene veiligheid
DA Almindelig sikkerhed
SV Allmän säkerhet
NO Alminnelig sikkerhet
FI Yleinen turvallisuus
EL Γενικήασφάλεια
SL Splošna varnostna navodila
SK Všeobecnábezpečnosť
CS Všeobecnábezpečnost
ET Üldine ohutus
HU Általános biztonság
LT Bendroji sauga
LV Vispārējādrošība
PL Ogólnezasadybezpieczeństwa
BG Общабезопасност
RO Informaţiigeneraleprivindsecuritatea
RU Общиесведенияобезопасности
HR Općasigurnost
TR Genel Güvenlik
ZH 一般安全
JA 一般的な安全対策
KO 일반안전
TH
VI CácVấnĐềAnToànChung
ID Keselamatan Umum
MS Keselamatan Am
General Safety
Pneumatic Grinders
Page 2
GS-2007
02-2014
PRODUCT DESCRIPTION:
Pneumaticgrindersareportablehandheldtoolspowered
by compressed air. The motor drives a rotating spindle
onwhichagrindingwheelorotherabrasivedeviceis
mounted.Whenapplicable,thegrinderisequippedwith
a guard.
Failure to observe all safety warnings could result in
equipment damage or personnel injury.
INTENDED USE:
A pneumatic grinder is to be used only for removing
materialbyutilizingappropriateabrasivewheels,rotary
les or other material removal cutting devices. The
grinder must not be modied in any manner unless
approvedinwritingbyApexToolGroup,LLCorApex
Tool Group GmbH & Co. OHG. All safety devices must
be properly installed and maintained in good working
order.
Any abuse or misuse of the cutting device can be
extremelydangerous.
GENERAL SAFETY INSTRUCTIONS:
These Safety Instructions must be accessible to the
operatoratalltimes.Theymustbeshownandmade
available to all personnel involved in the operation of this
equipment.
The operator must read and understand the
Safety Instructions contained in this document
before operating this equipment.
These Safety Instructions are not intended to be all
inclusive. The operator should also read and understand
the Product Manual for the specic tool. Study and
comply with all applicable Federal, State and Local
Regulations.
Do not remove any labels from this equipment. Replace
any label that has been damaged and can not be easily
read.
PRODUCT INSTALLATION:
Only qualied and trained personnel should install,
adjust or use this equipment.
WORK ENVIRONMENT:
Thework areamust beclean, uncluttered,thoroughly
ventilatedandwellilluminated.
Make sure the work environment is free of
anyammable orcombustibleelements that
sparks from the grinding process could ignite.
SPEED CHECK:
Checkthetoolspeedbeforemountingawheel,afterany
repairs,wheneverthetoolisissuedforuseorevery24
hours.TheRPMofthegrindermustbecheckedwitha
calibrated tachometer to make certain its actual speed
doesnotexceeditsratedspeed.
Carefullydetermineifthereisamaximumspeedmarked
on the cutting device. If so, this speed must be greater
thantheratedspeedofthetool.Failuretocomplywith
this instruction could result in serious injury or death.
GRINDING WHEEL INSPECTION:
Allgrindingwheelsshouldbecloselyinspectedbefore
installation and use. Consult the safety procedures of
thegrindingwheelmanufacturer.Includeblotterswhen
required.
PROPER ABRASIVE MOUNTING:
Therearemanytypesofcuttingwheelsincludingstraight,
cone, plug, cup, depressed center and mounted. Consult
and complywith theSafety Instructions ofthe cutting
wheel manufacturer. Insure the proper manufacturer
recommendedspindle,angesandguardsarepresent
on the tool.
Alwaysuseproperlymountedguards,asprescribedfor
the cutting device being used per ANSI/CAGI B186.1. If
the guard has been damaged, it must be discarded and
replaced.
Generally,rotarylesandsomeothercuttingdevicesdo
notrequirewheelguards.Conrmthiswiththecuttingtool
manufacturerandconformwiththeirrecommendations.
After mounting the cutting device and guard, the tool
should be started under a steel bench or similarly
protective area. Make sure safety glasses are worn.
Run at full speed for at least one minute to insure proper
operation.
GRINDING WITHOUT A GUARD:
Operators may use the grinder without a
guardonlyiftheyfollowtheserequirements.
Improper use of agrinder without a guard,
includingfailuretofollowtheserequirements,
could result in seriour injury or death.
Type 1 Wheel: Do not use a wheel larger than 2”
(50mm) in diameter or more than 1/2” (13mm) thick.
Neverexceedaperipheralspeedof1800surfacefeet
per minute (548.64m/min).
Type 1 Reinforced Wheel:Donotuseawheellarger
than3”(76mm)indiameterormorethan1/4”(6.4mm)
thick.Neverexceedaperipheralspeedof9500surface
feetperminute(2895.6m/min).
Grinding Wheels:Usedforinternalwork,whilewithin
theworkbeingground.
Mounted Wheels:Donotuseamountedwheelwitha
diametergreaterthan2”(50mm).
Other Cutting Devices: Do not use small cones, plugs,
threaded hole pot balls, or other similar devices that
exceed 3” (75mm) in diameter and 5” (125mm) long
withoutaguardunlesstheworkprovidesprotection.
CUT-OFF WHEELS (Type 1 and Type 27):
Securetheworkpiecetoprovideacleancutandreduce
the possibility of binding.
Ifthecut-offwheelbecomesjammed,turnthegrinder
offandfreethewheel.Makesurethewheelissecurely
attached and not damaged before continuing the
operation.
Never use a cut-off wheel to perform a side grinding
operation.
ENGeneral Safety
Pneumatic Grinders
WARNING
WARNING
WARNING

Produkt Specifikationer

Mærke: Dotco
Kategori: Kværn
Model: 10L2580-36

Har du brug for hjælp?

Hvis du har brug for hjælp til Dotco 10L2580-36 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Kværn Dotco Manualer

Dotco

Dotco 10L2582-01 Manual

27 August 2025
Dotco

Dotco 10L2500-01 Manual

26 August 2025
Dotco

Dotco 10L2502-01 Manual

26 August 2025
Dotco

Dotco 10L2580-01 Manual

26 August 2025
Dotco

Dotco 10L2500-36 Manual

26 August 2025
Dotco

Dotco 10L2562-01 Manual

26 August 2025
Dotco

Dotco 10L2580-36 Manual

26 August 2025

Kværn Manualer

Nyeste Kværn Manualer

Graphite

Graphite 56H650 Manual

7 Oktober 2025
Delta

Delta 23-207 Manual

7 Oktober 2025
Draper

Draper Storm Force 65137 Manual

1 Oktober 2025
Bavaria

Bavaria BAG 230 Manual

29 September 2025
Bavaria

Bavaria BMG 135 Kit Manual

29 September 2025
Yato

Yato YT-09742 Manual

29 September 2025
Bavaria

Bavaria BAG 125/1 Manual

29 September 2025
Clarke

Clarke CBG6RZ Manual

28 September 2025
Bavaria

Bavaria BAG 125 Manual

28 September 2025
Yato

Yato YT-09675 Manual

27 September 2025