Boston Acoustics KIT-SG-15 Manual

Boston Acoustics Guitarforstærker KIT-SG-15

Læs gratis den danske manual til Boston Acoustics KIT-SG-15 (3 sider) i kategorien Guitarforstærker. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Boston Acoustics KIT-SG-15, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

KIT-SG-15

Tools needed

Small Phillips screwdriver

2 gluing clamps

Good quality wood glue

Soldering iron and solder

Wrench 10 mm and 7 mm

Hammer

The iconic rock ‘n roll guitar available as a DIY kit. Like the original, this has a mahogany

body and neck. It is a slab body, so you can contour it to your own preference, very thin like

the original, or a bit beeer for your personal touch. The same can be said about the squa-

red o headstock. Let your imagination run free and form the headstock to your own

vision! The ngerboard is Cites-free pau ferro, a tone wood associated with custom shop

guitars. The hardware is chrome and two chrome humbucking pickups are included. This

kit has a neck that needs to be glued in, just like it has been since the 1960’s. The typical

tone is in your hands.

body : mahogany

neck : mahogany, set neck

ngerboard : pau ferro

bridge : T.O.M. type, chrome

pickups : 2 x humbucker

hardware : chrome

frets : 22

Wood

The base of each guitar is the wood construction. The neck pocket in our kits is perfect.

There is no need to work the neck pocket other than maybe a simple sanding. The neck

angle is ne and the neck can be glued in without a problem. Use proper wood glue and

apply the glue inside the neck pocket and that part of the neck that will go into the pocket.

Slide the neck into the pocket and xate the neck and the body with two gluing clamps.

Let dry for 24 hours. To prevent indentations, the body and neck should always be protec-

ted from the pressure of the gluing clamps. This surface protection can be done with thin

pieces of wood of cork.

After tightening the gluing clamps, wash away the excess glue with a damp cloth. All glue

residue will show and leave ugly spots during colouring and nishing, be accurate about

this.

Shape the headstock to your liking. Use les or saws and sanding paper to make your

headstock design neat and tidy. Make sure you remove all saw and sanding marks.

Sanding and nishing

When the glue has dried and your kit begins to look like a real guitar, you can prepare it to

be lacquered. Sand the body and neck with 320 grit dry sanding paper. After this step, use

masking tape to guard those parts that you don’t want to colour/nish. Always follow the

instructions on your nishing product, be it staining, spraying with aerosol cans or nis-

hing in a spraying booth. After the body and neck have been nished in the colour and

gloss of your choice, and you have polished your guitar to the desired result, it’s time to

install the hardware.

Electronics

Installing the electronics. First t the earth wire from the harness of potentiometers to the

studs. A hole is drilled from the electronic cavity to the stud of the tailpiece. After threading

the wire to the cavity of the stud, install the stud to secure the cable. Installing the stud is

done by tapping it gently with a hammer. Protect the stud by using a rubber hammer or

inserting a piece of wood or rubber between the hammer and the stud.

Now start soldering.

Install the pickups. The pickups are marked N and B. N is the neck pickup and B is the

bridge pickup. Thread the cables through the drilled holes into the electronics cavity. Use

the schematics to properly make all the connections. The potentiometers with the capa-

citor attached are the tone potentiometers, the other two are the volume potentiometers.

After you have nished soldering, check if everything works correctly before closing the

lids. In installing the potentiometers, output and selector switch make sure the nuts are

tightened so they will not cause unwanted resonance.

Hardware

Install the machine heads. Don’t forget the washers. Before drilling or punching a hole to

secure the machine heads, please align the machine heads on the back, so it looks neat

and tidy. Now fasten all screws and nuts. A loose washer or nut can cause unwanted reso-

nance.

Installing the bridge and tailpiece. Tap the studs in with a hammer. Use protection so you

don’t damage the stud. Install the wraparound bridge. Make sure the bridge is put on the

correct way. The small indentation in the saddle is for the high e string, bigger indentation

is for the low e string.

Put the strings on and start tuning the guitar.

Now the guitar needs a set up. Once tuned to pitch, check the neck curve and adjust to

your preference with the trussrod key. Check the frets for level. If the frets are not level

enough to your liking, level and polish the frets. Now adjust the string height so the guitar

plays comfortably all over the neck and there is no string buzz.

Finish setting up with adjusting the intonation. Now you are ready. You have built your

SG-15! Have fun playing it!

Produkt Specifikationer

Mærke:	Boston Acoustics
Kategori:	Guitarforstærker
Model:	KIT-SG-15

Har du brug for hjælp?

Hvis du har brug for hjælp til Boston Acoustics KIT-SG-15 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Guitarforstærker Boston Acoustics Manualer

Boston Acoustics KIT-SG-15 Manual

11 Januar 2026

Boston Acoustics KIT-LPJ-15 Manual

9 Januar 2026

Boston Acoustics KIT-TE-45 Manual

5 Januar 2026

Boston Acoustics KIT-FV-15 Manual

3 Januar 2026

Boston Acoustics KIT-LP-45 Manual

2 Januar 2026

Boston Acoustics KIT-JB-15 Manual

2 Januar 2026

Boston Acoustics KIT-ST-35 Manual

2 Januar 2026

Boston Acoustics KIT-LP-15 Manual

2 Januar 2026

Guitarforstærker Manualer

Nyeste Guitarforstærker Manualer

Electro Harmonix Abrams 100 Manual

28 December 2025

Blackstar HT-1R MkII Manual

20 Oktober 2025

Blackstar Unity 250 Manual

19 Oktober 2025

Victory V4 The Kraken Manual

15 Oktober 2025

Electro Harmonix Crayon Manual

6 Oktober 2025

Electro Harmonix Battalion Manual

6 Oktober 2025

Electro Harmonix Signal Pad Manual

6 Oktober 2025

Electro Harmonix Analogizer Manual

6 Oktober 2025

Electro Harmonix Muff Overdrive Manual

6 Oktober 2025

Electro Harmonix Stereo Clone Theory Manual

5 Oktober 2025