Draper 09021 Manual

Draper Donkraft 09021

Læs gratis den danske manual til Draper 09021 (6 sider) i kategorien Donkraft. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Draper 09021, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

09021

Original Instructions

Version 1 – July 2023

200kg

LOW

TRANSMISSION

JACK

This document is part of the product; retain it for the life of the product, passing it on to subsequent holders.

Read this manual in full before attempting to assemble, operate, or maintain this product. Always use the

latest version of the product manual, available from drapertools.com/manuals

3. Health and Safety

Instructions

Important: Read all the Health and Safety

instructions before attempting to operate, maintain

or repair this product. Non-compliance with these

instructions may result in injury or damage to the

user, the product or the load.

3.1 General Health and Safety

Instructions for this Product

• Only personnel who have read and understood

this manual and are trained in the use of this

product and the relevant forces are authorised to

operate this device.

• Observe all standard safety precautions and good

practices when in a workshop environment.

• Keep your work environment clear and well-lit,

with bystanders at a safe distance.

• Before every use, inspect the jack for broken,

cracked, loose or corroded parts.

Important: DO NOT use this product if it is

damaged in any way. Contact Draper Tools to

discuss repair and replacement options.

• DO NOT use this product if you suspect that it has

been subjected to abnormal loads or shock and

have it inspected by a qualied technician.

• Ensure that the warning labels and safety

instructions on the product are visible and

legible.

• Use the product only in the manner instructed in

this manual and modify it in any way.DO NOT

• ONLY use spare parts supplied by Draper Tools.

• DO NOT use this product if you are tired or under

the inuence of alcohol, drugs or other

medication.

• ALWAYS wear eye protection and protective

gloves and footwear when operating the jack.

1. Intended Use

This product is designed for lifting and lowering

transmission systems and dierentials within the

rated capacities during installation and removal. Any

other application beyond the conditions established

for use will be considered misuse. Draper Tools

accepts no responsibility for improper use of this

product.

Important: This product is suitable for NOT

elevating or supporting vehicles.

Part of our core range, this product is suitable for

regular use by enthusiasts and tradespersons alike.

2. Specication

Stock No.: 13885

Part No.: RC/TSL/50W

Rated. capacity: 200kg

Max. height: 600mm

Min. height: 160mm

Base dimensions: L 400 x W 417mm

Drive socket square drive size: 1 ⁄ 2"

Saddle type: Fixed

Net weight: 19.55kg

– 2 –

• Keep loose-tting clothes, jewellery and long hair tied

back to prevent it from snagging during operation.

• The wheels of this product DO NOT lock.

− Ensure that the jack will not roll once positioned

for use.

• ALWAYS ensure that the load is stable and secure in

the saddle before raising, lowering or transporting it.

• Before moving the jack, inspect the intended ALWAYS

route and ensure that it is clear of obstructions.

• Take care when moving the jack.

− ALWAYS ensure that the load is fully secure

before moving the jack.

− DO NOT use the jack on uneven surfaces that may

cause it to tip over.

− ALWAYS bring the load to its lowest possible

position before transportation.

− Stay alert for trailing straps that may interfere with

the movement of the jack, especially when under

load.

• NEVER leave the jack unattended when it is in use or

under load.

• When not in use, ensure that the lifting arm is in its

lowest position and the release valve is fully closed.

• This jack does not emit noise that exceeds a level of

70 dB(A) during operation.

WARNING! If the jack tips or leans while under

load, move immediately to a safe distance. DO

NOT attempt to steady or hold the jack.

3.2 Correct Use of the Transmission Jack

CAUTION! This product is designed to support

loads for short periods ONLY. DO NOT use this

product to support a load for longer than 30

minutes at a time.

• ONLY operate the jack on solid, level and horizontal

surfaces; a concrete surface is recommended, where

possible.

WARNING! NEVER use the jack on any

surface that is slippery or may sink or rock.

• NEVER attempt to lift or support any load that

exceeds the rated capacity of the jack.

• NEVER attempt to lift any load higher than the

maximum safe height of the jack.

• When attaching a load to the jack, use the ALWAYS

manufacturer’s recommended contact points.

• Ensure that the contact points are not dirty, greasy or

corroded.

• ALWAYS ensure that the load is fully detached from

its surroundings before moving it.

• NEVER allow anyone to position themselves or other

obstructions beneath the load during raising and

lowering or below any load supported only by the

jack.

• DO NOT stand or climb on the jack.

• Observe the saddle and load throughout the

operation and ensure that it does not drop without

intervention.

• Take all precautions to prevent movement of the load

during raising and lowering.

− Be aware that external forces may cause the load

to rock.

• Stay alert to external interference that may cause the

raised load to rock during preparation and operation.

− Should any dangerous conditions occur, cease all

operation until these conditions have been

rectied.

• Stay alert to the possibility of the load slipping from

the saddle and remain observant at all times.

• ALWAYS ensure that the vehicle is raised to the

correct height before attempting to move the jack

underneath it.

• ALWAYS ensure that the vehicle is level and

adequately supported before removing the

transmission or dierentials.

• Take any necessary precautions to prevent the vehicle

from sliding, including chocking the wheels (Rubber

Wheel Chocks, Stock No. 54500, for example).

• DO NOT move the jack further than is absolutely

necessary while under load.

− ALWAYS ensure that the route from the location

of engine to its destination is clear of obstructions

and is as short as possible.

• ALWAYS use a ratchet or breaker bar that allows the

operator to remain clear of the load during operation.

WARNING! NEVER operate this tool using an

impact wrench or other power tool.

WARNING! NEVER work under an unsupported

vehicle.

3.3 Residual Risk

The safety instructions in this manual cannot account for

all possible conditions and situations that may occur.

Exercise common sense and caution when using this

product and protect against any additional conceivable

risks.

Produkt Specifikationer

Mærke:	Draper
Kategori:	Donkraft
Model:	09021

Har du brug for hjælp?

Hvis du har brug for hjælp til Draper 09021 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Donkraft Draper Manualer

Draper Expert 70668 Manual

3 Oktober 2025

Draper Expert 28464 Manual

2 Oktober 2025

Draper Expert 24295 Manual

1 Oktober 2025

Draper Expert 02078 Manual

1 Oktober 2025

Draper Expert 02080 Manual

1 Oktober 2025

Draper Expert 19788 Manual

1 Oktober 2025

Draper 37058 Manual

1 Oktober 2025

Draper 31479 Manual

1 Oktober 2025

Draper Expert 02079 Manual

1 Oktober 2025

Draper Expert 31481 Manual

1 Oktober 2025

Donkraft Manualer

Nyeste Donkraft Manualer

NEO Tools 10-453 Manual

15 Oktober 2025

NEO Tools 10-451 Manual

15 Oktober 2025

NEO Tools 10-454 Manual

15 Oktober 2025

FERM FRJ-2000HL Manual

20 September 2025

WilTec 51157 Manual

31 August 2025

WilTec 50800 Manual

31 August 2025

Einhell HM 122 Manual

21 August 2025

Guede 2T Manual

31 Juli 2025

Guede 15T Manual

31 Juli 2025

Guede 3T Manual

30 Juli 2025