Dremel 400seriesXPR Manual

Dremel Slibemaskine 400seriesXPR

Læs gratis den danske manual til Dremel 400seriesXPR (72 sider) i kategorien Slibemaskine. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Dremel 400seriesXPR, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/72
Instructional Safety
Manual
400 Series XPR
High Performance Rotary Tool
Form No. 2610925455 10/04 Robert Bosch Tool Corporation © 2004
All Rights Reserved
1-800-437-3635
http://www.dremel.com
Dremel brand products are manufactured and sold by the
Dremel Division of Robert Bosch Tool Corporation
2
Read and understand all instructions. Failure to follow all instructions list-
ed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit.
Cluttered benches and dark areas invite acci-
dents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust
or fumes.
Keep bystanders, children, and visitors
away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
Double Insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified elec-
trician to install a polarized outlet. Do not
change the plug in any way. Double
Insulation eliminates the need for the three
wire grounded power cord and grounded
power supply system. Before plugging in the
tool, be certain the outlet voltage supplied is
within the voltage marked on the nameplate.
Do not use “AC only” rated tools with a DC
power supply.
Avoid body contact with grounded sur-
faces such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is grounded. If
operating the power tool in damp locations is
unavoidable, a Ground Fault Circuit
Interrupter must be used to supply the power
to your tool. Electrician’s rubber gloves and
footwear will further enhance your personal
safety.
Don't expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately. Damaged
cords increase the risk of electric shock.
When operating a power tool outside, use
an outdoor extension cord marked "W-A"
or "W." These cords are rated for outdoor
use and reduce the risk of electric shock.
Personal Safety
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
Dress properly. Do not wear loose cloth-
ing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
Keep handles dry, clean and free from oil and
grease.
Avoid accidental starting. Be sure switch
is “OFF” before plugging in. Carrying tools
with your finger on the switch or plugging in
tools that have the switch “ON” invites acci-
dents.
Remove adjusting keys or wrenches
before turning the tool ON. A wrench or a
key that is left attached to a rotating part of
the tool may result in personal injury.
Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enables better control of the tool in
unexpected situations.
Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions.
Tool Use and Care
Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand
or against your body is unstable and may
lead to loss of control.
Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.
Do not use tool if switch does not turn it
ON or OFF. Any tool that cannot be con-
trolled with the switch is dangerous and must
be repaired.
Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
WARNING
!
POWER TOOL SAFETY RULES

Produkt Specifikationer

Mærke: Dremel
Kategori: Slibemaskine
Model: 400seriesXPR

Har du brug for hjælp?

Hvis du har brug for hjælp til Dremel 400seriesXPR stil et spørgsmål nedenfor, og andre brugere vil svare dig


Slibemaskine Dremel Manualer

Dremel

Dremel 400seriesXPR Manual

16 September 2024
Dremel

Dremel 780 Manual

14 August 2024
Dremel

Dremel 10.8V Lithium-ion Manual

7 August 2024
Dremel

Dremel 300series Manual

4 August 2024
Dremel

Dremel 1100 Manual

18 Juli 2024

Slibemaskine Manualer

Nyeste Slibemaskine Manualer

Einhell

Einhell BT-MG 160 KIT Manual

29 Marts 2025
Kraftronic

Kraftronic KT-WS 2000 Manual

29 Marts 2025
Kraftronic

Kraftronic KT-WS 750 Set Manual

29 Marts 2025
NEO Tools

NEO Tools 14-014 Manual

28 Marts 2025
Makita

Makita 9500D Manual

28 Marts 2025
Bosch

Bosch GWS 30-180 PB Professional Manual

5 Februar 2025
Metabo

Metabo WVBF 18 LT BL 11-125 Quick Manual

1 Februar 2025
Parkside

Parkside PEXS 270 A1 Manual

13 Januar 2025
Makita

Makita 9562CVR Manual

12 Januar 2025
Chicago Pneumatic

Chicago Pneumatic CP7255 Manual

11 Januar 2025