Dremel 6000 Manual

Dremel Sander 6000

Læs gratis den danske manual til Dremel 6000 (35 sider) i kategorien Sander. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Dremel 6000, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/35
Contour Sander
Owner’s Manual
Model 6000
HONESTLY NOW … Have you read
this OWNER’S MANUAL?
26109 Printed in 25476 10/04 Mexico
©
Robert Bosch Tool
Corporation
1997
all rights reserved
P.O. Box 1468
Racine, Wisconsin 53401
1-800-437-3635
http://www.dremel.com
•Safety
•Assembly
•Operation
•Maintenance
•Accessory Information
•Warranty
• Service Parts
Parlez-vous français?
Voir page 12
¿Habla español?
Vea página 23
Dremel brand products are manufactured and sold by the
Dremel Division of Robert Bosch Tool Corporation
DM 2610919361 9/03 9/5/03 8:33 AM Page 1
Read and understand all instructions. Failure to follow all instructions
listed below, may result in electric shock, fire and/or serious personal
injury.
SAVE THESE INSTRUCTIONS
-2-
Work Area
Keep your work area clean and well lit.
Cluttered benches and dark areas invite
accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power
tools create sparks which may ignite the
dust or fumes.
Keep by-standers, children, and visitors
away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
Double Insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified
electrician to install a polarized outlet. Do
not change the plug in any way. Double
Insulation eliminates the need for the
three wire grounded power cord and
grounded power supply system. Before
plugging in the tool, be certain the outlet
voltage supplied is within the voltage marked
on the nameplate. Do not use “AC only”
rated tools with a DC power supply.
Avoid body contact with grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased
risk of electric shock if your body is
grounded. If operating the power tool in
damp locations is unavoidable, a Ground
Fault Circuit Interrupter must be used to
supply the power to your tool. Electrician’s
rubber gloves and footwear will further
enhance your personal safety.
Don't expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the
cord to carry the tools or pull the plug
from an outlet. Keep cord away from
heat, oil, sharp edges or moving parts.
Replace damaged cords immediately.
Damaged cords increase the risk of electric
shock.
When operating a power tool outside, use
an outdoor extension cord marked "W-A"
or "W." These cords are rated for outdoor
use and reduce the risk of electric shock.
Refer to “Recommended sizes of Extension
Cords” in the Accessory section of this
manual.
Personal Safety
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
Dress properly. Do not wear loose
clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewelry,
or long hair can be caught in moving parts.
Keep handles dry, clean and free from oil
and grease.
Avoid accidental starting. Be sure switch
is “OFF” before plugging in. Carrying tools
with your finger on the switch or plugging in
tools that have the switch “ON” invites
accidents.
Remove adjusting keys or wrenches
before turning the tool “ON”. A wrench or
a key that is left attached to a rotating part of
the tool may result in personal injury.
Do not overreach. Keep proper footing
and balance at all times. Proper footing
and balance enables better control of the
tool in unexpected situations.
Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions.
Tool Use and Care
Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand
!
WARNING
Power Tool Safety Rules
DM 2610919361 9/03 9/5/03 8:33 AM Page 2

Produkt Specifikationer

Mærke: Dremel
Kategori: Sander
Model: 6000

Har du brug for hjælp?

Hvis du har brug for hjælp til Dremel 6000 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Sander Dremel Manualer

Dremel

Dremel 8300 Manual

22 August 2024
Dremel

Dremel Model MM20 Manual

7 August 2024
Dremel

Dremel Model MM40 Manual

22 Juli 2024
Dremel

Dremel 6000 Manual

18 Juli 2024

Sander Manualer

Nyeste Sander Manualer

Kraftronic

Kraftronic KT-XS 420 Manual

29 Marts 2025
Kraftronic

Kraftronic KT-SS 250 Manual

29 Marts 2025
Makita

Makita BO5010 Manual

28 Marts 2025
Makita

Makita BO4554 Manual

28 Marts 2025
Bosch

Bosch GSS 140 A Manual

15 Januar 2025
Hazet

Hazet 9032M-53 Manual

1 Januar 2025
Alpha Tools

Alpha Tools DS 150 Manual

28 December 2024
Alpha Tools

Alpha Tools BBS 240 Manual

28 December 2024
Alpha Tools

Alpha Tools NTS 150/200 Manual

28 December 2024
RIKON

RIKON 50-300 Manual

27 December 2024