Dri-Eaz Velo Pro Manual

Dri-Eaz Varmeapparat Velo Pro

Læs gratis den danske manual til Dri-Eaz Velo Pro (4 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Dri-Eaz Velo Pro, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

109042H 1 Legend Brands, Inc.

Owner’s Manual

Velo® & Velo® Pro Low Profile Airmover

LEGEND BRANDS, INC.

15180 Josh Wilson Road, Burlington, WA 98233, USA

Phone: 932 7950+1 800- - - -3030 Fax: +1 360 757 LegendBrandsRestoration.com

The Velo and Velo Pro use a patented housing design to Airmovers produce concentrated, broad-path airflow to accelerate

the evaporation of moisture from materials for drying.

Patents: http://www.LBpatents.com

R E A D A N D U N D E R S T A N D T H E S E I N S T R U C T I O N S

WARNING! To reduce the risk of fire or

electric shock, do not use this fan with

any solid state speed control device.-

WARNING! Unit must be grounded. Do

not use with an extension cord. Connect only to an outlet

provided with a ground fault interrupting device.

WARNING! Never operate a unit with a damaged power

cord, as this may lead to electrical or fire hazards. If power

cord is damaged, it must be replaced by a cord of the

same type and amperage rating.

WARNING! Do not touch grills when unit is operating.

WARNING! Do not allow children to play with or around

the unit. Be sure the unit is inaccessible to children when

not attended.

WARNING! Always operate the unit on a stable, level

surface so it cannot fall and cause injury.

WARNING! Do not operate any fan with a damaged cord

or plug. Discard fan or return to an authorized service

facility for examination and/or repair.

WARNING! Do not run cord under carpeting. Do not cover

cord with throw rugs, runners, or similar coverings. Do not

route cord under furniture or appliances. Arrange cord

away from traffic area to avoid creating a trip hazard.

NOTICE: Keep motor dry. For indoor use only.

NOTICE: Unplug when not in use or when moving unit.

NOTICE: Do not alter or modify your Velo in any way. Use

only replacement parts authorized by Legend Brands, Inc.

Modifications or use of unapproved parts could create a

hazard and will void your warranty. Contact your

authorized Dri-Eaz distributor for assistance.

BEFORE YOU BEGIN

Warranty registration

Please visit warranty.legendbrandsrestoration.com to

Fig. B: Operating Positions

Horizontal

(for horizontal surfaces)

Vertical

(for walls and ceilings)

Right edge

(for wall drying)

Left edge

(for wall drying)

With stand for stairwells and

wall drying (Pro only)

Rear cord wrap under

bottom edge. Wrap cord

in either direction and

secure with plug clip.

Variable speed control

with amp readout (Pro

only).

Stand folds out

and locks (Pro

only).

Inlet grill. Keep clear

of obstructions.

Outlet grill. Keep

clear of obstructions.

On/Off and circuit breaker

reset switches.

GFCI-protected

power outlet sockets

with reset switch.

Fig. A: Parts Identification

109042H 2 Legend Brands, Inc.

required, have your equipment model, serial number and

original proof of purchase available and call your

distributor for assistance with obtaining a return material

authorization (RMA).

OPERATING INSTRUCTIONS

Note that the Velo can be placed in a variety of positions

for drying and air circulation. See Fig. B for details.

1. Unwrap the cord and plug the unit into a standard

115V protected -GFCI outlet. C Be sure AUTION:

switch is in the off position connecting unit to before

power outlet.

2. Velo surface Direct the outlet toward the to be dried.

TIP: On the Velo Pro, the airflow may be adjusted by

pressing the Up or Down arrow on the speed control (Fig.

D). A digital readout shows the approximate amp draw.

Use this value to maximize the number of Velo you can s

place on a single circuit.

3. the When surface dry to the touch, switch is unit off

and next areareposition the unit in the to be dried.

4. When finished, unplug the unit and re wrap the cord- in

the cord wrap.

For additional instructions about the use of airmovers for

restorative drying, see Tech Tips under Resources on

www.LegendBrandsRestoration.com.

Electrical safety devices

Circuit breaker: If the circuit breaker detects overload or

short circuit conditions, the breaker will automatically shut

off the electrical supply. If this occurs, check the power

cable carefully for any damage and ensure it is plugged

into a properly grounded outlet. Press the Circuit Breaker

Reset Switch (Fig. A) to reestablish the electrical supply.

G F C I :round ault ircuit nterrupter If the GFCI device

detects a ground fault, will automatically shut off the it

electrical supply. If this should occur, check the power

cable carefully for damage and ensure it is plugged into a

properly grounded outlet. Press the GFCI reset button

(Fig. A) to reestablish the electrical supply.

TRANSPORT AND STORAGE

Always use the handle to load or carry the unit.

Wrap cord in Cord Wrap tab either direction under front

and rear snug and secure bottom edge (Fig. A). Pull cord

with plug clip.

Units may be stacked for transport and storage.

When transporting in a vehicle, secure the unit(s) carefully

to prevent sliding and damage to the unit and/or injury to

vehicle occupants.

Keep unit dry. Do no expose the unit to rain or snow. t

MAINTENANCE

WARNING: Unplug unit before performing any

maintenance.

Before each use

Inspect the power cord. If cord is damaged, do not use.

Always grasp the plug (not the cord) to unplug.

As needed

The exterior may be cleaned with a mild solution of

detergent. Ensure housing is completely dry before use.

To clean interior, see Fig. C for instructions.

FOR SERVICE CALL YOUR LOCAL DISTRIBUTOR or

the Legend Brands Service Department at

800 932 3030- - .

Be sure to visit warranty.legendbrandsrestoration.com to

provide you with updated product information as needed.

WARNING: This product and other substances

that may become airborne from its use contain

chemicals, including lead, known to the State of California

to cause cancer, birth defects, or other reproductive harm.

For more information, go to P65Warnings.ca.gov

Fig. C: Disassembly

Fig. D ( Pro only)

Variable speed control with amp and total unit hours

display

To disassemble for cleaning:

1. Lay the unit on its top

(upside down). Remove the 4

blower bolts from the bottom

of the unit.

2. Turn the unit right side up

and remove the 14 screws

around the perimeter of the top

housing and electrical

enclosure.

3. Open the electrical box and

feed the blow cord back er

through the opening to create

slack inside the housing.

4. Lift the top housing shell

and electrical enclosure

together and flip them over

next to the base to expose the

inside of the housing.

5. Lift the blower out for full

access to the inside of the

housing.

6. Reverse the steps for

reassembly. IMPORTANT: Be

sure to pull any slack blower

cord back into the electrical

enclosure before the lid is

placed on the electrical

enclosure.

Produkt Specifikationer

Mærke:	Dri-Eaz
Kategori:	Varmeapparat
Model:	Velo Pro

Har du brug for hjælp?

Hvis du har brug for hjælp til Dri-Eaz Velo Pro stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Varmeapparat Dri-Eaz Manualer

Dri-Eaz Velo F518 Manual

23 August 2024

Dri-Eaz Velo Pro Manual

20 August 2024

Dri-Eaz Stealth AV3000 Manual

18 August 2024

Dri-Eaz Vortex Manual

17 August 2024

Dri-Eaz DriForce Manual

17 August 2024

Dri-Eaz Dri-Pod Manual

16 August 2024

Dri-Eaz Velo Manual

16 August 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

17 Juni 2025

17 Juni 2025

17 Juni 2025

17 Juni 2025

17 Juni 2025

17 Juni 2025

Life On Products LCAEA002 Manual

17 Juni 2025

Regency FG39-NG2 Manual

17 Juni 2025

Life On Products LCAEA003 Manual

17 Juni 2025

Life On Products LCAEA007 Manual

17 Juni 2025